BETOPPER LM30 Mini Spider User Manual
- June 14, 2024
- BETOPPER
Table of Contents
BETOPPER LM30 Mini Spider
Attention
- Don’t direct sight when opening the lamp;
- According to the operating instructions, please don’t disassemble the units without authorization , pls contact with the professionals if it break down.
- Must be installed by professional and technical personnel.
- Please place the products far away from the class of strobe lights .
- he unit must keep dry, don’t use in the rain , damp or dusty environments , need to use the waterproof equipment for protection when used in outdoors.
- Don’t touch the product or pull the power cord when your hand is wet.
- Please don’t switch frequently and avoid long time opening for fear f affecting the service life .
- Fixed installing to prevent the strong vibration or impact of units
- To prevent the foreign body into the units to avoid the breakdown
- The distance of units and light object should be kept in more than 50 cm.
- Pls don’t plug or turn on the units before the installation ;
- To check the plug and power cord head was connected well before power on,
- To use the original packaging and pay attention to Anti-vibration before transporting again,
- This symbol pointed out that the classified collection of relative electron and electronic equipment to collect.
Warranty
About Product Warranty
- Any product buy from our company ( or authorized agent), which used properly, and with this card, can have 1 year warranty for Lights, mechanical parts, electronic parts. If out of the warranty situation, we can provide the paid maintenance service.
- The warranty is no longer valid in the following situations:
- Warranty cards and products have no serial numbers
- Product is damaged or show significant signs of self-disassembly.
- Any unauthorized modification (removal or replacement) made to product or it’s components.
- Improper or excessive use of inappropriate repairs which result in a repair failure or injury.
- Did not follow instructions or use in an environment not suitable for product..
- Product damage caused by strong impact
- The warranty cannot be extended if the product as been serviced
- Light Source normal degradation
- Warranty card must be filled out with receipt of purchasing in order for the warranty to be valid.
- Product is damaged due to abnormal voltage or caused by other accidents (ex. Natural disasters).
- The Company reserves the right to interpret the provisions above.
The content of these articles is subject to change without notice!
Cleaning
The lens need to clean frequently to keep the better lighting effects , the frequency of cleaning depends on the environment, damp, smog or dirty environment is easy for dirt retention.
- with a soft linen and specialized glass abrasive cleaner ;
- wiping the units carefully ;
- wiping the outside of lens every 30 days at least .
Declare
The product is with good performance and complete package when it is
delivered. The end-user of this product should follow all the above
instructions and warnings. Any damage caused by misuse, malfunction and
problem caused by ignoring the instructions are not included in the repair
guarantees of the manufacturer or dealers .
All products made f rom Big Dipper Laser Company have anti identification.
please verify the anti-counterfeit label at the bottom of the case to ensure
the interests of consumers.
Interpretation of matters set forth in this manual belongs to Big Dipper Company
Inspection
In order to use the product securely and properly, please read the manual before using and follow the instructions strictly to prevent personal safety trouble and product damage caused by misuse.
Take care of the product, check the possibility of the product damage caused by transportation and check all the listed items are present upon receipt of the product:
Stage Light 1
Power cable 1
Use Manual 1
Warning
Forbid to turn on the machine when the lamp without masks or the housing was broken .
Structure Instructions
Operator Panel
- LED indicator light
DMX| bright| OMX signal input
---|---|---
MASTER| bright| Master Mode
SLAVE| bright| Slave Mode
SOUND| twinkle| Sound Control - function button
MENU/ESC| Main menu /return DOWN
---|---
DOWN| next option
UP| previous option
ENTER| confirm the function
Fault Handling
Solutions for defective problems :
A. The unit no working.no light, fans no working
- Check the power cord if connected well and fuse normal
- Check the voltage
- Check the power indicator light
B. Can’t controlled by controller
Operator Panel
- DMX indicator light must be lighted; if not ,check the OMX signal connector and signal cable , confirm the correct connect .
- If OMX indicator light lighted ,but no affect for OMX control, check if the OMX address code are correct .
- If with intermittent OMX signal transmission. check if Carron Socket connected well with signal cable
- Use other DMC controller to try again
- Check if OMX signal cable and high-tension wire with close distance ,will damage or jamming signal circuit .
C Without sound control
- Make sure the unit not received any OMX signal
- Check Mic if damaged
D. One OMX channel can’t control
- Stepper motor or motor leading wire was broken
- Motor drive circuit was broken
Channel
Channel | Value | Content |
---|---|---|
Y Axis motor10-255 | 0°-135° | |
2 | Y Axis motor20-255 | 0°-135° |
3 | Dimmer | 0-255 |
4 | Strobe | 0-9 |
10-255 | Strobe speed from slow to quick | |
5 | R Dimmer | 0-255 |
6 | G Dimmer | 0-255 |
7 | B Dimmer | 0-255 |
8 | W Dimmer | 0-255 |
9 | W Dimmer | 0-255 |
10 | B Dimmer | 0-255 |
11 | G Dimmer | 0-255 |
12 | R Dimmer | 0-255 |
13 | 130-199 | |
200-249 | Reset(3S) | |
250-255 | Single unit with sound control randomly |
Motor fine tuning operating
Press “MENU” button enter to Menu ,press “ENTER” button >3S,menu
interface
Shows TIL 1 (Y Axis 1 motor fine tuning)”,press “ENTER” button adjust to
value-127—-127 adjust the motor position. press “ENTER” button to store the
value for fine tuning.
Function button
CD Rear panel function button
-
OMX input. use 3-core XLR signal cable to connect the unit. then input
OMX signal -
DMX output, use 3-core XLR signal cable to connect the unit, output
OMX signal -
Power output: connect next unit. power input: to connect main po
Technical parameter
parameter|
---|---
LED light source| 8x3WLEDs
Power input| AC 100-240V, 50/60Hz
consumed power| 45W
Control mode| OMX, master-salve, sound control
OMX Channel| 7/13
Slave qty.| 120V/60Hz: 6 Pcs; 230V/50Hz : 10 Pcs
NW./G.W.| 2.6/3.3KGS
Standard equipped| power cordx1 , handlex1 , screw x2, user manual x1
Effect| Input program control the unit under master-salve mode controlled by
music,
0 – 100% smooth dimming function and various strobe effect, unique appearance design ,two-way scanning head, two-way swing multiple beam. with multiple beam dynamic scanning effect. highly dynamic ,to create a dreamy scene. available for bar ,high-end club, disco,
DMX channel function
Channel
Channel | Value | Content |
---|---|---|
1 | Y axis motor1 | 0-255 |
2 | Y axis motor2 | 0-255 |
3 | Dimmer | 0-255 |
4 | Strobe | 0—9 |
10-255 | Strobe speed from slow to auick | |
5 | Effect | 0-7 |
8-17 | effect1 | |
18-27 | effect2 | |
28-37 | effect3 | |
38-47 | effect4 | |
48-57 | effects | |
58-67 | effect6 | |
68-77 | effect? | |
78-87 | effect8 | |
88-97 | effect9 | |
98-107 | effect10 | |
108-117 | effect11 | |
118-127 | effect12 | |
28-136 | effect13 | |
137-146 | effect14 | |
147-156 | effect15 | |
157-166 | effect16 | |
167-176 | effect17 | |
177-186 | effect18 | |
187-196 | effect19 | |
197-206 | effect20 | |
207-216 | effect21 | |
217-226 | effect22 | |
227-236 | effect23 | |
237-246 | effect24 | |
247-255 | effect25 | |
6 | effect speed | 0-255 |
7 | 0-199 | |
200-249 | reset(3S) | |
250-255 | Single unit with sound control randomly |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>