JVC CS-V693 Series Car Stereo Speaker Instructions
- June 14, 2024
- JVC
Table of Contents
CAR STEREO SPEAKER
CS-V6934 INSTRUCTIONS
CS-V693 Series Car Stereo Speaker
For Customer Use:
Enter below the Model No. and Serial No. which is located either on the rear
or bottom of the speaker unit. Retain this information for future reference.
Model No…………………….
Serial No……………………
LVT1276-001A
©2005 Victor Company of Japan, Limited
Thank you for purchasing the JVC Car Stereo Speakers. These speakers can be
mounted in the rear tray, rear pillar or rear seat side panel of your vehicle.
For the secure installation and perfect operation of your speakers, please
read the following carefully. For Proper Installation and Use
- Be sure to install the speakers according to the directions so as to prevent them from slipping accidentally out of position due to the tossing and bumping of the vehicle.
- Set the wiring firmly on the floor of the vehicle, taking the utmost care not to break wires while installing.
- Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers.
- The amplifier and speakers should be connected between corresponding terminals, i.e. “left” to “left’, and “right to “right”, as well as “+” to “+”, and —” to “—”. Connection with reversed polarity will degrade the quality of stereo reproduction.
- Do not subject the speakers to excessive input. The power handling capacity of the CS-V6934 is 280 waits (MAX. MUSIC POWER). Any excessive input may damage the speakers.
- The CS-V6934 has an impedance of 4 ohms. Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.
- When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.
How to Complete the wiring
Consult the diagram below. Be sure to connect corresponding terminals, i.e.
“left” to “left’, “—” to “—”, etc. (Fig. 7) Downloaded from:
https://www.usersmanualguide.com/
CAUTION
Connect the provided speaker cord to the speaker terminal while holding the
lower portion of the speaker terminal. (Fig. 8)
How to Install
-
To install the speakers in the rear tray, first determine the appropriate area in which to place it. The speakers must be installed in a place where there are spaces of at least 37 mm over the tray and at least 87 mm under the tray. In determining the location,
make sure that the bottom part of each speaker fits into the large hole in the steel plate on which the rear tray is fixed. (Fig. 1) -
Remove the rear tray.
-
The paper pattern printed on the bottom of the packing box shows the exact shape of the area on the rear tray through which the speaker will be installed. Apply the paper pattern onto the area determined in 1. above, and trace out the shape of the area on the tray.
-
Then, cut out the marked area.
-
The next step is to wire the speakers. Consult the diagram carefully. (Fig. 7)
-
Use the provided tapping screw and speed nuts to fix the speaker and grille to the rear tray. First, remove the metal net from the grille. Align the 4 screw holes of the speaker frame and grille with those in the rear tray, insert the 4 screws and secure them with the nuts. Finally, attach the metal net to the grille (Fig. 2).
-
When installing the speakers under the tray without using the grilles, refer to Fig. 3 and 4.
-
The process for installing the speakers in the rear pillar or rear seat side panel, etc. from the top is generally the same as for installing the speakers in the rear tray. In this case, however, insert the speakers into the holes of the rear pillar or the side panel and secure them with the 4 screws. (Fig. 5 & 6)
-
In any case, make sure the connection between the speaker and speaker cords is correct, and pay attention to the speaker cone when installing.
-
Metal Net
-
Grille
-
Screw (M4 x 75 mm)
-
Speaker )
-
Nut (M4)
-
Screw (64 x 25 mm)
-
Speed Nut
Specifications
| Type | : 15 em x 23 om (6° x 9°) 3-Way Coaxial Speaker |
|---|---|
| Power Handling Capacity | : 280 watts (MAX. MUSIC POWER) |
| Impedance | :4 ohms |
| Magnet Mass | : 332g (11.7 oz) |
| Mass | : 1.36 kg (3.1lbs) |
{Oesign and specifications are subject to change without notice.)
Accessories
Grille x 2 Metal Net x 2 Screw (chit x 25 mm) x 8 Speed Nut x 8 Screw (M4 x 75
mm) x 8 Nut (M4) x 8 Speaker Cord (5 m) x 2
If a kit is necessary for your car, consult your telephone directory for the
nearest car audio speciality shop (“IN-CAR ENTERTAINMENT” dealer).
This file has been downloaded from:
www.UsersManualGuide.com
User Manual and User Guide for many equipments like mobile phones, photo
cameras, monther board, monitors, software, tv, dvd, and othes..
Manual users, user manuals, user guide manual, owners manual, instruction
manual, manual owner, manual owner’s, manual guide, manual operation,
operating manual, user’s manual, operating instructions, manual operators,
manual operator, manual product, documentation manual, user maintenance,
brochure, user reference, pdf manual
Downloaded from: https://www.usersmanualguide.com/