MONSTER E22 Bluetooth Earphones Ear Clip User Guide
- June 14, 2024
- Monster
Table of Contents
Model No: MH22180
OPEN EAR101
QUICK START GUIDE
Please read this Quick Start Guide carefully and keep it for future use.
Product Overview
Earphone x2 (left & right)
Charging Case
USB-C Charging Cable
Quick Start Guide and Warranty Letter
- LED Indicator
- Multi Function Button (MFB)
- Charging contact point
- Speaker Areas
- USB-C Charging Port
- Charging Indicator
Power On/Off
Open the cover of the charging case, take out the earphone, and it will turn on automatically. Put the earphone into the charging case, close the cover, and the earphone will automatically shut down and charge.
Charging Case Charging
Use the USB-C charging cable delivered with the product to charge, and the
charging case indicator shows the charging status.
When the charging case is fully charged, the charging case indicator lights
up.
Pairing
Open the cover of the charging case, take out the earphone, and it will turn on automatically. Later, you can hear “pairing” as a voice prompt. To connect to a new device, please turn on the Bluetooth of your mobile phone and search for “Monster Open Ear 101” to pairing the device. After successfully connecting, you will hear “connected” voice prompt.
Volume Control
Volume down: Double tap the MFB on the left earphone during music
streaming.
Volume up: Double tap the MFB on the right earphone during music
streaming.
Call
Answer / End a call: Single tap the MFB.
Reject the call: Press and hold the MFB for about 2 seconds.
Music
Play/Pause music: Single tap the MFB
Previous song: Press and hold the MFB on the left earphone for about 2
seconds.
Next song: Press and hold the MFB on the right earphone for about 2
seconds.
Voice Control
With the earphones connected to the phone, press the MFB key three times to
activate or disable the voice assistant.
Reset
When the earphones is powered on and not connected to the Bluetooth device,
press the MFB button of the left and right earphones five times at the same
time to restore factory Settings.
Indicator/Volce Prompt Guide
| Mode | Description | Voice Prompt |
|---|---|---|
| Power On | White LED light on | “Power On” |
| Power Off | White LED light off | “Power Off “ |
| Pairing | The white LED light in the main ear blinks quickly, and the white LED | |
| light in the secondary ear blinks every 6 seconds | “Pairing” | |
| Connected | White LED light off | “Connected” |
| Charging case | When charging, the indicator light on the charging case | |
| breathe, Keep it lit when it’s full | – |
Cautions
- After removing the earphones from the charging case, without pressing any buttons, the left and right earpieces will connect automatically. When no connections found, it will enter automatic pairing mode.
- Please place the earphones in the correct location (L/R) for normal charging.
- Replacement of battery (on your own) is Nat recommended.
- Do not expose battery (battery pack) to excessive heat such as direct sunlight or fire.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
cornpliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. he device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>