COMMSCOPE RVVPX310.11R-V2 6 Port Sector Antenna Owner’s Manual
- June 14, 2024
- CommScope
Table of Contents
- COMMSCOPE RVVPX310.11R-V2 6 Port Sector Antenna
- Product Information
- Product Usage Instructions
- General Specifications
- Remote Electrical Tilt Information
- Dimensions
- Array Layout
- Port Configuration
- Electrical Specifications
- Mechanical Specifications
- Packaging and Weights
- Regulatory Compliance/Certifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
COMMSCOPE RVVPX310.11R-V2 6 Port Sector Antenna
Product Information
| Product Name | RVVPX310.11R-V2 |
|---|---|
| Antenna Type | Sector Multiband |
| Band | 10 MHz – 30 MHz |
| Color | Light Gray (RAL 7035) |
| Grounding Type | RF connector inner conductor and body grounded to the |
reflector and
mounting bracket
Radome Material| Fiberglass, UV-resistant
Radiator Material| Low-loss circuit board Aluminum
RF Connector Interface| 7-16 DIN Female
RF Connector Quantity, high band| 4
RF Connector Quantity, low band| 2
RF Connector Quantity, total| 6
RET Interface| 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity| 1 female | 1 male
Input Voltage| Internal RET
Power Consumption, idle state, maximum| 2 W
Power Consumption, normal conditions, maximum| 13 W
Protocol| 3GPP/AISG 2.0 (Single RET)
Dimensions| Width: 350 mm | 13.78 in
Depth: 208 mm | 8.189 in
Length: 2533 mm | 99.724 in
Net Weight, without a mounting kit: 32 kg | 70.548 lb
Product Usage Instructions
To use the RVVPX310.11R-V2 product, follow the instructions below:
- Make sure the product is properly grounded by connecting the RF connector inner conductor and body to the reflector and mounting bracket.
- Install the antenna in an outdoor location, considering wind loading figures provided in the white paper WP-112534-EN.
- Connect the RF connectors to the appropriate devices or cables. The antenna has a total of 6 RF connectors, with 4 for high band and 2 for low band.
- If using the RET functionality, connect the RET interface using the provided 8-pin DIN Female and Male connectors. The product supports 1 female and 1 male RET interface.
- Ensure proper input voltage is provided to the internal RET.
- Monitor the power consumption of the product to ensure it stays within the specified limits (2 W idle state, maximum; 13 W normal conditions, maximum).
- Configure the protocol according to your requirements, using the 3GPP/AISG 2.0 (Single RET) protocol.
- Place the antenna in the desired location, considering its dimensions (Width: 350 mm, Depth: 208 mm, Length: 2533 mm) and its net weight of 32 kg.
6-port sector antenna, 2x 694–960 and 4x 1695–2690 MHz, 65° HPBW, 3x RET with manual override.
- Integrated Internal Remote Electrical Tilt (RET), with independent control of electrical tilt with manual override on all arrays
- All Internal RET actuators are connected in “Cascaded SRET” configuration
OBSOLETE
This product was discontinued on: March 27, 2020
General Specifications
- Antenna Type Sector
- Band Multiband
- Color Light Gray (RAL 7035)
- Grounding Type RF connector inner conductor and body grounded to the reflector and mounting bracket
- Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
- Radome Material Fiberglass, UV resistant
- Radiator Material Low-loss circuit board
- Reflector Material Aluminum
- RF Connector Interface 7-16 DIN Female
- RF Connector Location Bottom
- RF Connector Quantity, high band 4
- RF Connector Quantity, low band 2
- RF Connector Quantity, Total 6
Remote Electrical Tilt Information
- RET Interface 8-pin DIN Female | 8-pin DIN Male
- RET Interface, quantity 1 female | 1 male
- Input Voltage 10–30 Vdc
- Internal RET High band (2) | Low band (1)
- Power Consumption, idle state, maximum 2 W
- Power Consumption, normal conditions, maximum 13 W
- Protocol 3GPP/AISG 2.0 (Single RET)
Dimensions
- Width 350 mm | 13.78 in
- Depth 208 mm | 8.189 in
- Length 2533 mm | 99.724 in
- Net Weight, without mounting kit 32 kg | 70.548 lb
Array Layout
Port Configuration
Electrical Specifications
- Impedance 50 ohm
- Operating Frequency Band 1695 – 2690 MHz | 694 – 960 MHz
- Polarization ±45°
- Total Input Power, maximum 1,000 W @ 50 °C
Electrical Specifications
Electrical Specifications, BASTA
Mechanical Specifications
- Wind Loading @ Velocity, frontal 445.0 N @ 150 km/h (100.0 lbf @ 150 km/h)
- Wind Loading @ Velocity, lateral 379.0 N @ 150 km/h (85.2 lbf @ 150 km/h)
- Wind Loading @ Velocity, maximum 942.0 N @ 150 km/h (211.8 lbf @ 150 km/h)
- Wind Loading @ Velocity, rear 472.0 N @ 150 km/h (106.1 lbf @ 150 km/h)
- Wind Speed, maximum 241 km/h | 149.75 mph
Packaging and Weights
- Width, packed 436 mm | 17.165 in
- Depth, packed 320 mm | 12.598 in
- Length, packed 2720 mm | 107.087 in
- Weight, gross 54 kg | 119.049 lb
Regulatory Compliance/Certifications
Agency/Classification
- CE Compliant with the relevant CE product directives
- CHINA-ROHS Above maximum concentration value
- ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
- REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
- ROHS Compliant/Exempted
- UK-ROHS Compliant/Exempted
Included Products
T-029-GL-E – Adjustable Tilt Pipe Mounting Kit for 2.362″-4.5″ (60-115mm) OD
round members for panel antennas. Includes 2 clamp sets
Footnotes
Performance Note Severe environmental conditions may degrade optimum
performance
©2023 CommScope, Inc. All rights reserved. CommScope and the CommScope logo are registered trademarks of CommScope and/or its affiliates in the U.S. and other countries. For additional trademark information see https://www.commscope.com/trademarks. All product names, trademarks and registered trademarks are property of their respective owners. Revised: May 25, 2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>