PCNA MC160-R Watch Charging Wire Instruction Manual
- June 14, 2024
- PCNA
Table of Contents
Watch charging wire
Instruction Manual
MC160-R Watch Charging Wire
Item:
7143-65
Model: MC160-R
Functions:
- 2-in-1 (Lightning & Micro) Output
- Type-C output
- iWatch Charging Surface
- Type-C Input
- USB-A Input
What’s included:
1 x Charging Cable
Tech Specifications
- Input: USB-A & Type-C
- Output: Type-C & 2-in-1(Micro & Lightning)
- Wireless Output: 2.5W
- Charge Current: 2A
- Cable length: 120cm
Instructions:
1. Charging Mobile Phones and Other Electronic Devices:
- Plug the charging cable into either the Type-C input port (4) or the USB-A input port (5) on the adapter.
- If using USB-A, ensure it’s securely connected to the Type-C input port.
- Attach the 2-in-1(1) or Type-C(2) output port of the charging cable to your mobile phone or any other rechargeable device for charging.
- To charge your iWatch, simply position it on the designated iWatch charging area (3).
SAFETY PRECAUTIONS:
• WARNING-When using this product, basic precautions should always be followed:
- Read all the instructions before use.
- Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C).
- Do not overcharge your phone. The unit may become hot under excessive use. Remove your phone once it is fully charged. Never charge your phone for more than 7 hours at a time.
- To reduce the risk of injury, close supervision is required when the product is used near children.
- Do not expose the device to moisture.
- Do not use the device in excess of its output rating. Overload outputs above the rating may result in a risk of fire or injury
- Do not use the device if damaged or modified.
- Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
- Do not disassemble the device. For repairs, seek a qualified service professional. incorrect reassembly may result in a risk of fire or injury.
- Do not expose the device to fire or excessive temperature. Exposure to fire or temperatures above 104T may cause explosion.
- To ensure product safety, ensure that identical replacement parts.
- Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. You must remove attachments from the phone before charging on this device.
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1 ) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
• Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user s authority to operate the
equipment.
Note : This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located for operating in conjunction with any other antenna or transmitter.
IC Statement :
• This device contains license-exempt transmitter (s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radio Frequency Exposure Statement for IC
This equipment complies with IC exposure limits set forth for an uncontrolled
environment. This equipment shall be installed and operated with minimum
distance 10 cm between the radiator & body.
Name of the Distributor:
Leedsworld Inc
Address of the Distributor:
400 Hunt Valley Road,
New Kensington,
PA 15068 USA.
WWW.PCNA.COM
FCC ID: XXXXXXXXXX
IC: XXXXXXXXXX
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>