Itek ITMF24I181F HD Monitor User Manual

Itek ITMF24I181F HD Monitor

Precautions

Before using this product, please read this User Manual carefully and keep it well

• Keep the monitor away from water sources or damp places, such as bathrooms, kitchens, basements and swimming pools.
• Make sure the monitor is placed on a flat surface. If the monitor falls, it may cause human injury or device damage.
• Store and use the monitor in a cool, dry and well-ventilated place, and keep it away from emission and heat sources.
• Do not cover or block the vent hole in the rear casing, and do not use the product on a bed, sofa, blanket or similar objects.
• The range of the supply voltage of the monitor is printed on the label on the rear casing. If it is impossible to determine the supply voltage, please consult the distributor or local power company.
• If the monitor will not be used for a long period, please cut off the power supply to avoid electric shock in rainy days and damage due to abnormal supply voltage.
• Please use a reliable grounded socket, Do not overload the socket, or it may cause fire or electric shock.
• Do not put foreign matters into the monitor, or it may cause short circuits resulting in or electric shock.
• Do not disassemble or repair this product by yourself to avoid electric shock. If faults occur, please contact the after-sales service directly.
• Do not pull or twist the power cable forcefully.
• There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged and the warranty will be invalid.

Package Content

Packing list

• Please check that the package of the monitor contains all the parts. If any part is lost, please contact the distributor.
• The colour and shape of parts may vary with models. Figures in this User Manual are for reference only. Cables supplied may vary with purchased products. Figures in this User Manual are for reference only.

Redundant screws can be used as spare screws.

Installation

Installation of base

1. Open the package to take out foams and put them on a flat tabletop.
2. Remove the upper foam cover and put it aside, take out the monitor film bag and put the monitor in the lower foam cover.
3. Take out the stand, install it on the rotary shaft of the monitor and tighten them with 2 screws.
4. Take out the base, align it with the bottom of the stand and tighten them with 2 screws.
5. Simply hold the stand with your hand to stand the monitor upright.
   Note: During standing of the whole monitor, do not press the liquid crystal screen with your hand to avoid damage to the screen.

Mount Installation

1. Open the package to take out foams and put them on a flat tabletop.
2. Remove the upper foam cover and put it aside, take out the monitor film bag, and put the monitor in the lower foam cover. Take out the mount adapter and 2 screws and tighten the mount adapter with 2 screws.
3. Do not pinch the screen directly with your hands during the process of hanging the product to prevent the screen from breaking.
   Notes: To prevent the monitor on the mount from failing, please install it firmly and protect it fully. Do not place or hang any object on the mount, and the height of the mount should be less than 2 meters.

Adjustment of monitor

Instructions for use

Description of buttons

function values.
2| Rocker switch button: press to turn on/off the monitor.
3| Left rocker button:Press to return to the previous menu/ Exit.
4| Downrocker button: Move the joystick down to view menu options or decrease function values.
5| Right rocker button: Press to enter sub-menus/ quickly enter the main menu.

Explanation of indicators

Indicator
Steady blue light indicates the power is on and the monitor runs normally. Red light indicates no video source and no horizontal or vertical signal detected or low voltage. Please make sure that your computer is turned on and all video cables are fully plugged in and/or connected.

Cable connection

• The bottom interface configuration at the back of the monitor varies with products.
• Note: If the power cable or signal cable is damaged, you must replace it with special soft cables or special components purchased from the manufacturer or maintenance department.

OSD menu

Menu description

The colour and shape of the OSD menu of the actual computer may be slightly different from those shown in the figure. Specifications of the OSD menu may change with improvements of functions without prior notice. The on-screen display (OSD) menu can be used to adjust the settings of the monitor and is displayed on the screen after turning on the monitor and pressing the Left rocker button.

1. Push the rocker key (Right) to enter the OSD main menu or enter the sub-menus or confirm the selection.
2. Push the rocker key (Up) to enter the Contextual Model move up in the menu or change the settings in the sub-menus.
3. Push the rocker key (Down) to enter the GamePlus Switching move down in the menu or change the settings in the sub-menus.
4. Push the rocker key (Left) to enter the Input Signal or exit the current screen.

The functions of the monitor vary with models, and the functions in this manual are for reference only.

Game Settings

| Standard Mode| Off, On
---|---|---
RTS/RPG Mode| Off, On
FPS Arena Mode| Off, On
MOBA Arena Mode| Off, On
Adaptive-Sync| Off, On
Shadow Balance| 0-100
Response Time| Off, Normal, Fast, Ultrafast
Refresh Rate| Off, On
Game Crosshair| Off,on( Crosshair1,Crosshair2,Crosshair3,Crosshair4,Crosshair5, Crosshair6)
Game Time| Off, on( 15:00, 30:00, 45:00, 60:00 ,Position)
Dynamic Brightness| Off, Normal, Expert, Elaboration
MPRT| Off, On
Ambient Lighting| Off, On

Picture Settings

| Brightness| 0-100
Contrast| 0-100
DCR| Off, On
Contextual model| Off, On( Movie Mode, Reading Mode, Night Mode)
Low Blue Light| 0-100
Sharpness| 0-5
Gamma| 1.8, 2.0, 2.2, 2.4, 2.6, S.curve
Aspect Ratio| Wide Screen, 4:3,1:1, Auto

Color Settings

| Warm| Off, On
Natural| Off, On
Cool| Off, On
User1| Off, On(R:0-100, G:0-100, B:0-100)
User2| Off, On(R:0-100, G:0-100, B:0-100)
User3| Off, On(R:0-100, G:0-100, B:0-100)
Hue| R,G,B,C,M,Y
Saturation| R,G,B,C,M,Y

OSD Settings

| Language| 简体中文, English,       ,         , Portugues do Brasilazil, Deutsch, Nederland, Suomi, Français, Ελληνικά, Indonesia, Italiano, 日 本 語 , Malaysia, Polskie, Português, Pусский, Español, , Українська, Ti ng Vi t,

繁體中文, Türkçe

---|---|---
OSD Time Out| 5-100
OSD H-Position| 0-100
OSD V-Position| 0-100
OSD Transparency| 0-5
OSD Rotation| Normal, 90, 180, 270
OSD Lock| Off, On
Hotkey1 Setting| Brightness, Contrast, Volume, Mute, Shadow Balance, Game Crosshair, Refresh Rate, Game Time, Adaptive-Sync, Contextual Model, Input Signal, Dynamic Brightness, Ambient Lighting
Hotkey2 Setting
Hotkey3 Setting

Other Settings

| Input Signal| Auto, DP, HDMI
Volume| 0-100
Mute| Off, On
Auto Power| Off, On
Eyeshield Remind| Off, On
Reset| No, Yes
Information| Input Source/Resolution/Mode

Basic parameters

Environmental conditions

| Action| Temperature: 0°C~ 40°C (32°F ~ 104°F) Humidity: 10%~90% RH (non- condensing)
Storage| Temperature: -20°~ 60° (-4°F ~ 140°F) Humidity: 5%~95% RH (non- condensing)

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.

Common troubleshooting

The following table contains general information about common monitor problems you might encounter and the possible solutions.
Bestit Srl, via dei Fabbri, 40050, Funo di Argelato, Bologna, Italy Web: www.itekevo.com
Mail: info@itekevo.com

References

• Homepage - Itek
• Homepage - Itek

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>