Honda HRX Series Lawn Mowers Owner’s Manual

OWNER’’S MANUAL

HRX217VLAA
HRX217VLPA
LAWN MOWER

HRX Series Lawn Mowers

Before operating the mower for the first time, please read this Owner’s Manual. Even if you have operated other mowers, take time to become familiar with how this mower works and practice in a safe area until you build up your skills.

REGISTER YOUR PRODUCT

To register your mower, scan the Q%{ codi or see page 27 for additional ways to register.

QUESTIONS?
Contact your Honda dealer.
There is a dealer locator at powerequipment.honda.com

© 2020-2023 American Honda Motor Co., Inc —All Rights Reserved

WELCOME

Congratulations on your selection of a Honda lawn mower!
We are certain you will be pleased with your purchase of one of the finest lawn mowers on the market. We want to help you get the best results from your new mower and to operate it safely. This manual contains information on how to do that; please read it  carefully.
‘When your mower needs scheduled maintenance, keep in mind that Honda Power Equlpment servicing dealership personnel are specially trained in servicing Honda mowers and are supported by the parts and service divisions of American Honda.
Please read the DISTRIBUTOR’S LIMITED WARRANTY on page 22 and the EMISSION CONTROL SYSTEM WARRANTY on page 23 to fully understand what is covered by warranty and your responsibilities of ownership.

FOR YOUR SAFETY

Your safety and the safety of others are very important. We have provided important safety messages in this manual and on the mower.
This information alerts you to potential hazards that could hurt you or others. Please read these messages carefully.
Of course, it is not practical or possible to warn you about all the hazards associated with operating or maintaining a lawn mower. You must use your own good judgment.

Safety Instructions
You will find important safety information in a variety of forms:

• Safety Labels — on the lawn mower

• Instructions — how to use this mower correctly and safely

• Safety Messages — preceded by a safety alert symbol and one of three signal words: DANGER, WARNING, or CAUTION.
  Each message tells you what the hazard is, what can happen, and what you can do to avoid or reduce injury.
  These signal words mean:
  DANGER
  You WILL be KILLED or SERIOUSLY HURT if you don’t follow instructions.
  WARNING
  You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.
  CAUTION
  You CAN be HURT if you don’t follow instructions.

• Damage Prevention Messages — you will also see other important messages that are preceded by the word NOTICE. This word means:

NOTICE
Your mower, other property, or the environment can be damaged if you don’t follow instructions.

WARNING:
The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.

Important Message to Parents
The safety of your children is very important to Honda. Lawn mowers are tools, not toys. As with any equipment, bad judgments can result in serious injuries. Your child must be big enough, strong enough, and have the coordination necessary to comfortably  reach and operate the controls. Anyone who takes unnecessary risks and doesn’t obey rules should not operate this lawn mower.

Safety Label Locations
These labels warn you of potential hazards that can cause serious injury. Read them carefully. If a label comes off or becomes hard to read, contact an authorized Honda servicing dealer for a replacement.

PARTS AND CONTROLS

INITIAL MOWER SETUP

List of Parts
With help from an assistant, carefully remove the mower and loose parts from the carton and compare the loose parts against the following list. Contact the authorized Honda dealer from whom you purchased the mower if any of the loose parts shown are not  included with your mower.

Adjust the Handlebar

1. With the handlebar adjust knobs in the unlocked position, pull the blade control lever against the handlebar, and then raise the handlebar into the mowing position.
2. Align the adjust knobs with one of the three holes on each handle stay. Setting the adjust knobs in the lowest holes raises the handlebar to its highest position.
3. Turn the handlebar adjust knobs 90 degrees into the lock position, making sure both sides are positioned at the same height.
4. Remove all the cardboard from around the handlebar.

Add Engine Oil
The mower is shipped WITHOUT OIL in the engine. Remove the oil filler cap/dipstick and add the entire contents of the included bottle of ail into the oil filler opening.

All Honda engines are run at the factory prior to packaging. Most of the oil is removed prior to shipment; however, some oil remains in the engine. The amount of oil left in the engine varies.
If you don’t use the supplied oil, add enough SAE 10W-30 API service category SJ or later oil to bring the oil level between the upper and lower limit marks on the dipstick—without screwing the dipstick in.
See “Oil Change” on page 13.
Do not overfill the engine with oil. If the engine is overfilled, the excess oil may get transferred to the air cleaner housing and air filter.
An indication of overfilling is white or blue smoke coming from the muffler when the engine is running.
After filling the engine with oil, screw the filler/cap dipstick in and remove the hang tag near the recoil starter grip that says “The engine has no oil.”

Assemble the Grass Bag

1. Turn the grass bag right-side out.
2. Pullthe frame support legs outward and slide them into the eyelets as shown.
3. Install the assembled frame into the fabric grass bag, keeping the grass bag handle exposed.

Please Register Your Mower
Please take a few minutes and register your purchase with Honda.
You can register:

• By completing and mailing the registration card on the back cover of this manual
• Scanning the QR code to the right and completing the online form
• Going online to powerequipment.honda.com/reg

Before Using Your Lawn Mower
All Mower operators must read the following sections:

• FOR YOUR SAFETY (page 2)
• BEFORE EACH OPERATION (page 4)
• OPERATION (page 7)
• MAINTENANCE SCHEDULE (page 11)

BEFORE EACH OPERATION

Your safety is your responsibility. A little time spent in preparation will significantly reduce your risk of injury.
Read and understand this manual. Know what the controls do and how to operate them.
Familiarize yourself with the lawn mower and its operation before you begin using it. Know how to quickly shut off the lawn mower in case of an emergency.
Check Your Mower
For your safety, and to maximize the service life of your lawn mower, it  is very important to take a few moments before you operate the lawn mower to check its condition. Be sure to take care of any problem you find, or have your servicing dealer correct it,  before you operate the lawn mower.

WARNING
Improperly maintaining this lawn mower, or failing to correct a problem before operation, could cause a significant malfunction.
Some malfunctions can seriously hurt or kill you.
Always perform a pre-operation inspection before each operation, and correct any problem.

• Make sure the lawn mower is on a level surface
• Look around and underneath the lawn mower for signs of oil or gasoline leaks
• Look for signs of damage
• Check each control for proper operation
• Check the blades for wear. Replace as necessary (page 12)
• Check that the blade bolts are tight (page 12)
• Check that all nuts, bolts, and screws are tightened
• Check the air filter (page 13) and oil level (page 6)
• Check the fuel level (page 7). Starting with a full tank will help to eliminate or reduce operating interruptions for refueling.

Check Your Mowing Area
For your safety and the safety of others, always inspect the area before operating the lawn mower.
Anything that can be picked up by the blades and thrown is a potential hazard to you and others. Look for things like stones, sticks, nails, and wire, and remove them from the lawn area.
People and animals near the lawn area can move into your lawn mower’s path or into a position where they could be struck by thrown objects. Clear the area of pets and people, especially children. Their safety is your responsibility.
Check the condition of the grass. Adjust your lawn mower ground speed and mowing swath accordingly.

Clip Director®
The Clip Director can be adjusted to any one of the ten positions to achieve the desired mowing results (bag, bag and mulch, or mulch).
To adjust the Clip Director knob, pull the knob downward and towards the rear of the mower. The knob adjusts a sliding door from the fully open BAG position to the fully closed MULCH position.
Some grass accumulation in the discharge opening is normal when the Clip Director is fully closed in the MULCH position. To remove this grass, close the discharge guard, fully open the Clip Director in the BAG position, engage the blade control lever, and start  the engine.
If a high resistance is noticed when moving the Clip Director knob from side- to-side, excessive grass may have built up on top of the sliding door.

Important Safety Precaution
Always release the blade control lever and disconnect the spark plug cap (page 14) before lifting the discharge guard to view or clean around the sliding door. This will prevent contact with the rotating blades and prevent objects from being thrown into the  discharge area.
Sliding Door Position
The sliding door can be positioned to produce different mowing results. If the preferred sliding door position is unknown, install the grass bag and begin mowing with the Clip Director knob all the way to the BAG position. Check the appearance of the lawn. As  the knob is moved towards the MULCH position, more grass will be recycled back into the lawn. Adjust the Clip Director knob until the desired result is achieved.

Rear Discharge
To discharge clippings to the rear, remove the grass bag and position the Clip Director knob in the BAG range. Maximum rear discharge will occur when the Clip Director knob is all the way to the left (BAG) position. As the Clip Director knob is moved toward the  right (MULCH) position, less grass will be discharged through the rear discharge guard.

Fallen Leaves
Use the Clip Director to shred and collect fallen leaves for disposal.
Set the front wheels so they are one or two settings higher than the rear. Set the Clip Director in position #9 (not quite full mulching), and adjust the setting from this point for best results.
Collecting leaves while they are damp will help to control dust and result in more effective mulching of the leaves.

Rear Shield
During normal use the rear shield is subject to deterioration and wear.
Remove the grass bag and raise the discharge guard to check the rear shield for cracks or tears. If the rear shield is excessively worn, have it replaced by your authorized Honda servicing dealer.

Grass Bag
A lawn mower works like a vacuum cleaner; it blows air through the bag fabric, which traps the grass clippings. Always empty the grass bag before it becomes filled to the limit of its capacity. Bagging performance will diminish after the bag becomes about 90%  filled.
Also, the bag is easier to empty when it is not packed full.
You can leave the grass bag on the mower during mowing, even when full mulching is selected.
To minimize dust and fine particles from passing through the grass bag fabric, it is best to mow grass in the morning when the ground is slightly damp and the grass is dry.
Inspection
During use, the grass bag material is subject to normal wear and tear.

CAUTION
An excessively worn grass bag may allow objects to be thrown toward the operator.
Thrown objects can hurt you.
Replace a worn grass bag to prevent possible injury.

Installation

1. Raise the discharge guard and hook the grass bag onto the mower deck as shown.
   Clean any grass clippings from the hook channel.

2. Release the discharge guard to secure the grass bag.

Removal

1. Raise the discharge guard, grasp the grass  bag handle, andremove the grass bag.
2. Release the discharge guard.
3. When the grass  bag is clear of the discharge guard, you can lift it through the handlebar opening or remove it to the rear of the mower below the handlebar.

Cutting Height Adjustment
Each wheel of the mower can be adjusted to one of seven settings.
The actual height of cut grass will vary with lawn and soil conditions.
Be sure the engine is not running when adjusting the cutting height.

To adjust cutting height, pull each adjustment lever toward the wheel, and move it into another notch.
Move all four adjustment levers to the same position, forward for tall grass and rearward for short grass.

If you are not sure what cutting height to select, start with a high setting and check the appearance of the lawn after mowing a small area. Then readjust the cutting height if necessary.

Check the Oil Level

1. Unscrew and remove the filler cap/dipstick and wipe itclean.

2. Insert and remove the dipstick without screwing it into the filler neck.
   Check the oil level shown on the dipstick.

3. Ifthe oil level is low, add oil to reach the upper limit mark on the dipstick.
   Do not overfill. If the engine is overfilled, the excess oil may get transferred to the air cleaner housing and air filter. An indication of overfilling is white or blue smoke coming from the muffler when the engine is running.
   Use 10W-30 API Service category SJ oil for normal  conditions. For additionaloil recommendations, see “Engine Oil Recommendations” on page 13.
   NOTICE
   Running the engine with a low oil level can cause engine damage.

4. Screw in the filler cap/dipstick securely.

Add Fuel
This engine is certified to operate on regular gasoline with a pump octane rating of 86 or higher.
Never use stale or contaminated gasoline or an oil/gasoline mixture.
Avoid getting dirt or water in the fuel tank.
‘You may use regular unleaded gasoline containing no more than 10% ethanol (E10) or 5% methanol by volume. In addition, methanol must contain cosolvents and corrosion inhibitors.
Use of fuels with content of ethanol or methanol greater than shown above may cause starting and/or performance problems. It may also damage metal, rubber, and plastic parts of the fuel system.
Engine damage or performance problems that result from using a fuel with percentages of ethanol or methanol greater than shown above are not covered under warranty.

WARNING
Gasoline is highly flammable and explosive, and you can be burned or seriously injured when refueling.

• Stop the engine and let it cool before refueling
• Keep heat, sparks, and flame away
• Refuel only outdoors
• Wipe up spills immediately

If your equipment will be used on an infrequent or intermittent basis, (more than 4 weeks before next use), refer to “AVOIDING FUEL-RELATED PROBLEMS” on page 20 for information regarding fuel deterioration.

1. Turn the engine off and let cool before refueling.

2. Remove the fuel tank cap.

3. Add fuel into the neck of the fuel tank to the UPPER LIMIT line
   (Approx. 2 inches (53 mm) from the top of the fuel filler neck). Do not overfill. Wipe up any spilled fuel before starting the engine.
   

4. Tighten the fuel tank cap until it clicks.
   Move the mower at least 10 feet (3 meters) away from the fueling source and site before starting the engine.

NOTICE
Fuel can damage paint and plastic. Be careful not to spill fuel when filling your fuel tank. Damage caused by spilled fuel is not covered by the DISTRIBUTOR’S LIMITED WARRANTY (page 22).

OPERATION

For your safety, avoid starting or operating the engine in an enclosed area, such as a garage. Your mower’s exhaust contains poisonous carbon monoxide gas, which can collect rapidly in an enclosed area and cause illness or death.

WARNING
Exhaust contains poisonous carbon monoxide gas that can build up to dangerous levels in closed areas.
Breathing carbon monoxide can cause unconsciousness or death.
Never run the lawn mower in a closed, or even partially closed area where people may be present.

You may hear a clicking noise as you push the lawn mower forward with the engine OFF. This is normal and will not damage the mower.
Safe Mowing Practices
Most injuries and property damage with walk-behind mowers can be prevented if you follow all instructions in this manual and on the mower. The most common hazards are discussed below, along with the best way to protect yourself and others.
Avoid Rotating Blades
Rotating blades can cause serious cuts and even amputate fingers, hands, toes, or feet. Keep away from the mower deck whenever the engine is running. If you need to adjust the cutting height or work around the deck for any other reason, always shut off the  engine.
Wear heavy gloves and disconnect the spark plug cap when you need to clean the mower deck or handle the blades.

DANGER
The blades are sharp and spin at high speed. If you come in contact with a spinning blade, it will cut you severely and can amputate fingers and toes.

• Wear protective footwear
• Keep your hands and feet away from the mower deck while the engine is running
• Stop the engine before performing any adjustment, inspection, or maintenance

Clear Mowing Area
Mower blades can throw rocks and other objects with enough force to cause serious injury. Before mowing, carefully inspect the area and remove all sticks, stones, pieces of wire, and other loose objects.
Never operate the blades over gravel.
NOTICE
Striking objects with the spinning blades can cause severe engine damage, which is not covered by the DISTRIBUTORS LIMITED WARRANTY (page 22).
Keep Shields in Place
Guards and shields are designed to protect you from being hit by thrown objects and from hot engine parts and moving components.
For your safety and the safety of others, keep all shields in place when the engine is running.

Refuel With Care
Gasoline is extremely flammable and gasoline vapor can explode.
Refuel only outdoors, in a well-ventilated area, with the engine OFF.
Never smoke near gasoline, and keep other flames and sparks away.
Always store gasoline in an approved container.
Wear Protective Clothing
Wearing protective clothing will reduce your risk of injury. Long pants and eye protection reduce the risk of injuries from thrown objects.
Sturdy shoes with aggressive soles will help protect your feet and give you better traction on slopes or uneven ground.
Stop the Engine When Not Mowing
If you need to leave the mower for any reason, even just to inspect the lawn ahead, stop the engine by releasing the blade control lever.

Avoid Slopes
Avoid steep slopes of more than 20°.
Mow across slopes, not up and down. Be careful when changing direction. Mowing on a slope when the grass is damp or wet could cause you to slip, fall, and lose control of the mower. 

NOTICE
Mowing on steep slopes can starve the engine of oil, causing engine damage that is not covered by the DISTRIBUTORS LIMITED WARRANTY (page 22).
Keep all four wheels on the ground, and be careful to avoid losing your footing and your control of the mower. Keep a firm grip on the handlebar, and walk, never run, with the mower. Be very careful when mowing uneven or rough ground.
If stuck, do not kick or shove the mower with your foot. Use the handlebar to control the mower.
Avoid Obstacles
Gravel, loose stones, and landscaping material can be picked up by the mower and thrown many feet with enough force to cause serious personal injury and/or property damage. The best way to prevent potential injury from thrown objects is to release the blade  control lever to stop the blades before reaching areas with gravel, loose stones, or landscaping material.
Be careful when mowing over obstacles that stick up above the surface of the lawn such as sprinkler heads, paving, edging, raised tree roots, etc.
If the blade hits something, or if the mower starts to vibrate, stop the engine immediately, disconnect the spark plug cap, and check for damage (page 12). Striking objects may damage the blades, bend the crankshaft, and/or break the mower deck or other components.
Vibration usually indicates serious trouble.

WARNING
Aworn, cracked, or damaged blade can break, and pieces of the damaged blade can become dangerous projectiles.
Blades thrown from the mower could seriously hurt or kill someone.
Inspect the blades regularly (see page 12), and do not operate the mower with a worn or damaged blade.

The DISTRIBUTOR’S LIMITED WARRANTY (page 22) does not cover parts damaged by accidental impact collision.

Operating the Controls

Blade Control Lever

The blade control lever must be pulled back against the handlebar to start and run the engine. The blades start to rotate when the lever is pulled back against the handlebar and the recoil starter grip is pulled.

Continue to hold the lever fully against the handlebar. This will keep the engine and blades rotating smoothly and prevent premature wear to the flywheel brake system.
Release the blade control lever to stop the engine and stop blade rotation whenever you need to leave the mower.

Select Drive Control
With the engine running and the blades rotating, slowly push the Select Drive control to propel the mower forward.
Normal operation is with your hand comfortably around the handle bar and Select Drive control.
Push the Select Drive control with your thumb into the indentation for extra torque (up a hill, or through thick grass).

You can reduce the ground speed by partially releasing the Select Drive control.
Ground speed varies with terrain, grass height, slope, and grass bag weight. Moving the Select Drive knob (shown below) or varying how far you push the Select Drive control forward allows you to maintain the desired ground speed under constantly changing  mowing conditions.
Release the Select Drive control to disengage (stop) the rear wheels.
Disengage the drive when mowing around trees and other obstacles.
Push the mower around obstacles for better directional control.

Adjusting the Select Drive Control
The Select Drive control knob allows you to adjust the maximum ground speed when the Select Drive lever is fully engaged.
Adjustment is from MIN to MAX. With the Select Drive lever fully engaged:
MIN will propel the lawn mower at its slowest speed.
MAX will propel the lawn mower at its fastest speed.

The position of Select Drive knob determines the forward speed of the lawn mower, but it still varies based on the mowing surface and terrain. For example, with the knob in the slowest position, the mower may seem to propel quickly on smooth concrete.
However, once the lawn mower is moving through grass, it will go slower because of the added resistance of the grass.

Starting the Engine
The blades turn when you start the engine. Start the engine in a clear or mowed area where the blades can turn freely.

1. Turn the fuel valve to the ON position (page 3).
2. Pull back on the blade control lever and hold it against the handlebar.
3. Start the engine using the electric starter or the recoil (manual) starter.

Electric start:
Turn the starter key switch to the START position. Let the key return to the RUN position when the engine starts.

The starter should not be cranked for more than 5 seconds at a time. If the engine fails to start, release the switch and wait 10 seconds before operating the starter again.
If the battery does not have sufficient charge to start the engine, possibly due to a long storage period, use the recoil starter to start the engine for at least one mowing session. The battery should have sufficient charge after one mowing session (approximately 1  hr). An optional plug-in charger is also available, see page 21 for the part number and ordering information.
Manual start:
Pull the starter grip lightly until you feel resistance, and then pull briskly. Return the starter grip gently.

To ensure easy restarting and maximum performance from the Auto Choke System, allow the engine to run for at least three minutes after starting a cold engine before stopping the engine. This minimum run time will be longer if the temperature is below 70 °F  (21 °C).
Continue to hold the blade control lever against the handlebar; the engine stops when the blade control lever is released.

Stopping the Engine

1. Release the blade control lever to stop the engine and blade rotation.
2. When you finish mowing, turn the fuel valve OFF.
3. If your mower will not be used for 3 to 4 weeks, we recommend running the engine’s carburetor out of fuel. You can do this by leaving the fuel valve OFF, restarting the engine and running it until it stops. See “AVOIDING FUEL-RELATED PROBLEMS” on  page 20 if you don’t plan to use your mower for a month or more.
4. Clean your mower after each mowing; refer to “Cleaning” on page 16.

Mowing Tips
When to Mow
Most grasses should be mowed when they have grown %z to 1 in (12 ~ 25 mm) above their recommended height. More frequent mowing is required for mulching than for bagging. For best mulching results, you may need to mow the lawn twice a week during the growing season.
Cutting Height
Consult a local nursery or lawn and garden center for cutting height recommendations and advice about specific types of grasses and growing conditions in your area.
Most grass has stems and leaves. If you cut off the leaves, you’ll scalp the lawn. Let the grass recover between mowings. Your mower will work better, and your lawn will look better.
Cutting grass that is too tall or mowing the lawn too quickly can clog the mower deck with grass and may cause the engine to stall. If your grass gets too tall, cut it once at the highest cutting height setting using a slow ground speed, then mow again in 2 or 3 days. Don’t take off more than one third of the total grass height in any one mowing, or brown patches may develop. Cutting height adjustment is explained on page 6.
Cutting Width
For an even lawn finish, overlap each mowing swath by a few inches.
If the grass is very tall or thick, use more overlap and a narrower mowing swath.
Blade Speed
The blades must spin very fast to cut properly. If engine speed drops, it could mean the engine is being overloaded by the blades trying to cut too much grass. Mow a narrower swath, move the mower slower, use the rear discharge chute, or raise the cutting  height.
Blade Sharpness
A sharp blade cuts cleanly. A dull blade tears the grass, leaving shredded ends that turn brown. When your blades don’t cut cleanly anymore, have them sharpened or replaced.
Dry Grass
If the ground is too dry, mowing will stir up a lot of dust. Besides being unpleasant to work in, too much dust will clog the air filter. If dust is a problem, water your lawn the day before mowing. Mow when the grass is dry to your touch, but the soil is still moist.
Wet Grass
Wet grass is slippery and can make you lose your footing. Also, wet grass clippings will clog the mower deck and collect in clumps on the lawn. Always wait for wet grass to dry before mowing.
Fallen Leaves
When equipped with the grass bag, your mower can be used to pick up fallen leaves for disposal. If using the mower to bag large amounts of fallen leaves, and not for mowing, set the cutting height adjustment levers so the front of the mower deck is one or two  settings higher than the rear.
If you want to mulch fallen leaves into your lawn, don’t let the leaf cover get too deep before you begin. For best results, start mulching while grass still shows through the leaf cover. In places where fallen leaves completely cover the grass, remove the leaves by  raking, or install a grass bag, so your mower can pick them up for disposal.
Collecting leaves while they are damp will help to control dust and result in more effective mulching of the leaves. You can also shred leaves using the Clip Director; see page 5 for details.

Clogged Mower Deck
Before clearing a clogged mower deck, stop the engine and turn the fuel valve to the OFF position. With the spark plug cap disconnected, tilt the mower so the carburetor side is up.
Clear a clogged deck with a stick, not your hands.
Mowing Patterns
Your Honda mower will work most efficiently if you use the following mowing patterns as much as possible. Mower deck and equipment design, and the direction in which the blade rotates, cause these mowing patterns to provide the best results.

Mulching
Use a counterclockwise mowing pattern. If the lawn has an irregular shape, or many obstacles, divide it into sections where you can use counterclockwise patterns.

Bagging
Use a clockwise mowing pattern.
This will give the best bagging performance, leaving the least amount of clippings on the lawn.

SERVICING YOUR MOWER

Proper maintenance is essential for safe, economical, and trouble-free operation. It also helps reduce air pollution.

WARNING
Improper maintenance, or failure to correct a problem before operation, can cause a serious malfunction.
Some malfunctions can seriously hurt or kill you.
Always follow the inspection and maintenance recommendations and schedules in this owner’s manual.

To help you properly care for your mower, the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Other service tasks that are more difficult or require special tools are best  handled by professionals and are normally performed by a Honda technician or other qualified mechanic.
The maintenance schedule applies to normal operating conditions. If you operate your mower under severe conditions, such as sustained high load, high temperature, or unusually wet or dusty conditions, consult your servicing dealer for recommendations  applicable to your individual needs and use.
Remember that an authorized Honda servicing dealer knows your mower best and is fully equipped to maintain and repair it. To ensure the best quality and reliability, use only new, Honda Genuine parts or their equivalents for repair and replacement.
Maintenance, replacement, or repair of the emission control devices and systems may be performed by any engine repair establishment or individual, using parts that are “certified” to EPA standards.
Maintenance Safety
Some of the most important safety precautions follow. However, we cannot warn you of every conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task.

WARNING
Improper maintenance can cause an unsafe condition.
Failure to properly follow maintenance instructions and precautions can cause you to be seriously hurt or killed.
Always follow the procedures and precautions in this manual.

Safety Precautions

• Make sure the engine is off before you begin any maintenance or repairs. This will eliminate several potential hazards:
  — Carbon monoxide poisoning from engine exhaust.
  Be sure there is adequate ventilation whenever you operate the engine.
  — Burns from hot parts.
  Let the engine and exhaust system cool before touching.
  — Injury from moving parts.
  Do not run the engine unless instructed to do so.

• Read the instructions before you begin, and make sure you have the tools and skills required.

• To reduce the possibility of fire or explosion, be careful when working around gasoline. Use only a nonflammable solvent, not gasoline, to clean parts. Keep cigarettes, sparks, and flames away from all fuel-related parts.

Maintenance Schedule

Item| Action| Before each use| 5 hours of use or first month| First 25 hours of use| 50 hours of use or every 6 months| 100 hours of use or every  year| 150 hours of use or every two  years|

See page

---|---|---|---|---|---|---|---|---
Rear shield| Check| O| | | | | | 5
Blades| Inspect| O| | | | | | 12
Blade mounting bolts| Inspect| O| | | | | | 12
** Engine oil| Check| O| | | | | | 6
Change| | O| | O (2)| O| O| 13
Air filter| Check| O| | | | | | 13
Clean| | | O (1)| O (1)| O (1)|
Replace| | | | | | O
Grass bag| Check| O| | | | | | 6
Blade control operation| Check| O| | | | O| | 14
Spark plug| Check| | | | | O| | 14
Replace| | | | | | O
Spark arrester (optional part)| Clean| | | | | O| | 14
Select Drive cable| Adjust| | O| O| O| O| O| 15
Fuel tank/filter| Clean| | | | | O (3)| | —
Flywheel brake pad| Check| | | | | O (3)| | —
Valve clearance| Check- adjust| | | | | O (3)| | —
Pinion gears| Grease| | | | | O (3)| | —
Rear wheel adjuster bushings| Inspect- grease| | | | | | O (3)| —
Fuel lines| Check| Check every 2 years and replace if necessary (3)| —**

1. Service more frequently when used in dusty areas.
2. Change engine oil every 25 hours when used under heavy load or in high outside air temperatures.
3. These items should be serviced by an authorized Honda servicing dealer unless you have the proper tools and are mechanically proficient.
   Refer to the Honda shop manual for service procedures. See “Honda Publications” on page 21 for ordering information.

Failure to follow this Maintenance Schedule could result in non-warrantable failures.

Blade Inspection

1. Tumn the fuel valve OFF (page 3).
2. Disconnect the spark plug cap from the spark plug (page 14).
3. Tilt the mower to the right side so that the fuel cap side is up. This will help to prevent fuel leakage and hard starting due to carburetor flooding.
4. Inspect the blades for damage, cracks, and excessive rust or corrosion.

WARNING
Aworn, cracked, or damaged blade can break, and pieces of the damaged blade can become dangerous projectiles.
Blades thrown from the mower could seriously hurt or kill someone.
Inspect the blades regularly, and do not operate the mower with worn or damaged blades.

A dull blade can be sharpened, but a blade that is excessively worn, bent, cracked, heavily rusted, or otherwise damaged must be replaced.

If a blade is bent, take the lawn mower to an authorized Honda servicing dealer for inspection.

Blade Mounting Bolt Inspection
Inspect the blade bolts for any signs of damage or looseness. If they are damaged, they must be replaced.

If they appear loose, a torque wrench must be used to accurately tighten the blade bolts to the required torque. If you do not have a torque wrench, take your lawn mower to an authorized dealer to have the bolts replaced or tightened.
Use only Honda Genuine blade bolts and special washers, since they are specifically designed for this purpose. Replacement part numbers are on page 21.

Blade Replacement

1. Tum the fuel valve OFF (page 3).

2. Disconnect the spark plug cap from the spark plug (page 14).

3. Tilt the mower to the right side so that the fuel cap side is up. This will help to prevent fuel leakage and hard starting due to carburetor flooding.

4. Remove the two blade bolts with a 14 mm (6 point) socket wrench.
   Use a wooden block to prevent the blades from turning when removing the bolts. Remove the blades.
   

5. Clean dirt and grass from around the blade mounting area.

6. Install the sharpened or replacement blades using the two blade bolts and special washers as shown below. Be sure to install the washers in the direction shown.
   Always install both blades as a set.
   The blade bolts and washers are specially designed for this application. When replacing bolts and washers, use only Honda Genuine replacement parts.
   WARNING
   Operating the mower with only one blade will result in an improperly seated blade that can become dangerous projectiles.
   Blades thrown from the mower could seriously hurt or kill someone.
   Always install both blades as a set.

7. Tighten the blade bolts with a torque wrench to the specified torque. Use a wooden block to prevent the blades from turning when tightening the bolts, as shown on page 13.
   Blade bolt torque: 36 ~ 43 ft-Ib (49 ~ 59 N-m)
   If you do not have a torque wrench, have an authorized Honda servicing dealer tighten the blade bolts.

WARNING
If the blade bolts are not torqued properly, the blades could loosen and be thrown from the mower.
Blades thrown from the mower could seriously hurt or kill someone.
Ensure the blade bolts are torqued properly.

Oil Change
Change the oil after the first month or 5 hours of use. Thereafter, change the oil every 6 months or 50 hours of use. Change the oil more frequently when used under heavy load or high outdoor temperatures. See “Engine Oil Recommendations” on this page for recommended oil properties.
Drain the used oil while the engine is warm. Warm oil drains quickly and completely.
To reduce the chance of scratching the side of the mower deck or wheels when tipping, place a piece of cardboard or drop cloth on the ground. The use of a commercially available siphon pump will save time and make the oil change easier.

1. Turn the fuel valve OFF (page 3). This will reduce the possibility of fuel leakage.

2. Wipe the oil filler area clean, and then remove the oil filler capl/dipstick.

3. Place a suitable container next to the mower to catch the used oil, and then tilt the mower on its right side.
   The used oil will drain through the filler neck. Allow the oil to drain completely.
   After draining, take the oil to your local recycling center or service station. Do not throw it in the trash, pour it on the ground, or pour it down a drain.

4. Fill with the recommended oil.
   Do not overfill. Allow a couple of minutes for the oil to settle in the engine, and then measure the oil level (page 4).
   Refill amount:
   120~1350z
   (0.35~0.40 L)
   NOTICE
   Using non detergent oil can shorten the engine’s service life, and using 2-stroke oil can damage the engine.

Engine Oil Recommendations
Oil is a major factor affecting performance and service life. Always change the oil in accordance with the Maintenance Schedule (page 11).
Recommended oil for general use: SAE 10W-30
Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range.

The SAE oil viscosity and service category are in the API label on the oil container. Honda recommends API service category SJ or later oil.

Air Filter
Clean the air filter after the first 25 hours of use. Thereafter, clean the filter every 6 months or 50 hours of use. Clean the filter more often when used in dusty areas. Replace the filter every 2 years or 150 hours of use.
Aproperly maintained air filter will help prevent dirt from entering your engine. Dirt entering the carburetor can be drawn into small passages in the carburetor and cause premature engine wear. These small passages can become blocked, causing starting or  running problems.
NOTICE
Operating the engine without an air filter, with a damaged air filter, or with an improperly installed air filter cover will allow dirt to enter the engine, causing rapid engine wear. This type of damage is not covered by the DISTRIBUTOR’’S LIMITED WARRANTY  (page 22).
We recommend the use of a Honda Genuine air filter to ensure it seals and performs as designed. Using a non-Honda air filter can result in dirt bypassing the filter, causing damage to the engine or fuel system.

1. Press down on the cover tabs and remove the cover.

2. Remove the filter from the air cleaner housing.
   

3. Inspect the filter; replace if damaged.

4. Clean the filter by tapping it several times on a hard surface to remove dirt, or blow compressed air (not exceeding 30 psi [207 kPa]) through the air filter from the inside. Never try to brush off dirt; brushing will force dirt into the fibers.

5. Wipe dirt from the inside of the air cleaner housing and cover using a moist rag. Be careful to prevent dirt from entering the air duct that leads to the carburetor.

6. Reinstall the filter and cover. Be sure both tabs are fully locked in place.

Spark Plug
Replace the spark plug every 2 years or after 150 hours of use.
Required Spark Plug: NGK – BPR5ES
NOTICE
An incorrect spark plug can cause engine damage.

For good performance, the spark plug must be properly gapped and free of deposits.

1. Allow the engine to cool, disconnect the spark plug cap, and remove any dirt from around the spark plug area.

2. Remove the spark plug with a 13/16 in (21 mm) spark plug wrench.

3. Inspect the spark plug.
   Replace it if the electrodes are worn, or if the insulator is cracked or chipped.

4. Measure the spark plug  gap with a suitable
   Gap: 0.028 ~ 0.031in
   (0.7 ~ 0.8 mm)
   Correct the gap, if necessary, by carefully bending the side electrode.

5. Install the spark plug carefully, by hand, to avoid cross-threading.

6. After the spark plug seats, tighten with a 13/16 in (21 mm) spark plug wrench to compress the washer
   If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the spark plug seats.
   If installing a new spark plug, tighten 1/2 turn after the spark plug seats.
   Spark plug torque: 14 ft-Ib (20 N-m)
   A loose spark plug can overheat and damage the engine.
   Overtightening the spark plug can damage the threads in the cylinder head.

7. Install the spark plug cap on the spark plug.

Spark Arrester (optional part)
The spark arrester must be serviced every 100 hours to keep it functioning as designed.
Your lawn mower engine is not factory-equipped with a spark arrester.
In some areas, it is illegal to operate an engine without a spark arrester. Check local laws and regulations. An optional USDA approved spark arrester is available from an authorized Honda servicing dealer. See “Parts, Accessories, and Service Items” on page 21  for the part number.

1. Allow the engine to cool.
2. Unclip the two red top cover tabs [6] on the muffler side of the engine, and then slightly lift the red top cover up to expose the upper muffler shield bolt.
3. Remove the three bolts [1] from the muffler shield [2] using a 10 mm socket wrench.
4. Remove the muffler shield [2].
5. Remove the set screw [4].
6. Remove the spark arrester [3] from the muffler [5].
7. Check for carbon deposits on the spark arrester and the exhaust port. Brush carbon deposits away. Be careful to avoid damaging the spark arrester screen.
8. Install the spark arrester into the muffler.
9. Install the muffler components on the engine, and tighten the three bolts securely.

Blade Control Check

1. Start the engine outdoors.
2. Release the blade control lever; the engine should stop quickly.
   If it does not, take your mower to an authorized Honda servicing dealer for repair.

Select Drive Cable Adjustment

With the engine off, loosen the jam nut one revolution.
With the Select Drive control released, TIGHTEN the adjuster by turning clockwise 1 revolution by hand, and then pull the lawn mower rearward to check resistance.
If no wheel resistance exists, repeat the above procedure until the wheels lock when pulling rearward. It will usually take more than 8 turns for the wheels to lock up.
Next, mark the adjuster and LOOSEN the adjuster counterclockwise 8 complete revolutions.
Hold the adjuster and tighten the lock nut against the adjuster. Push the lawn mower forward and pull backward and check for little or no resistance.
Start the engine to ensure the lawn mower does not move forward without pushing the Select Drive control.

Charging the Battery
The lawn mower engine has an internal charging system. Under normal mowing usage it is not necessary to charge or maintain the battery.
If the mower fails to start or has been stored for an extended period:

• Start the lawn mower using the recoil starter manually for at least one mowing session. This should charge the battery sufficiently to use the electric starter
• If the electric starter does not operate (after manually starting for one mowing session), check the 3 Amp and 30 Amp fuses (shown  to the right)
• If the electric starter still does not operate, take the lawn mower to an authorized Honda servicing dealer
• If you prefer, there is an optional AC powered plug-in battery charger shown below

Optional Battery Charger
The optional battery charger is available through your Honda servicing dealer, see page 21 for ordering information.

Charge the battery as follows:

NOTICE
Only use a genuine Honda 12 volt charger or equivalent with a maximum rated output less than 1 A.
Do not charge using a standard automotive charger.

1. Disconnect the charge port connector on the handle, below the recoil starter rope grip.
2. Locate the battery charger adapter harness, and connect the adapter harness into the charge port connector that is closest to the battery.
3. Insert the connector on the Honda battery charger into the other end of the adapter harness.
4. Plug the charger into a standard 120 volt AC power outlet and let the battery charge. The charger may become slightly warm during charging, this is normal. The float charger can be left connected continuously when the lawn mower is not in use.
   Light color| Description
   ---|---
   Red light| Charging battery
   Green light| Charger is tending battery at 13.6V
   No light| Charger unplugged or malfunctioning

After charging the battery, disconnect the adapter harness from the charge port connector, and then firmly reconnect the charge port connectors on the handle together. The adapter harness may be left connected to the battery charger when not in use.

NOTICE
Battery will not charge properly when the handle is folded and the  battery is upside side down.

Replacing the Battery

1. Remove the battery cover by removing the three battery cover mounting screws.
2. Carefully remove the battery from the box, and then pull the connector away from the terminals.
3. Carefully position the battery in the case without pinching the wires. The wires must be routed above the top side of the battery exactly as shown.

Replacing a Fuse
The electric starter circuit and battery are protected by a 30 Amp and 3 Amp fuse. If the 30 Amp fuse burns out, the electric starter will not operate and if the 3 Amp fuse burns out, the battery will not charge.
The engine can be started with the recoil starter if either fuse burns out.

1. Remove the battery cover by removing the three cover mounting screws.
2. The 30 Amp fuse is for main line protection. The 3 Amp fuse is for the charge line protection.
3. Remove and inspect the fuses. If they are burned out, replace with a serviceable fuse.

If a frequent fuse failure occurs, it usually indicates a short circuit or an overload in the electrical system. Take the mower to an authorized Honda servicing dealer for repair.

TRANSPORTING

If the engine has been running, allow it to cool before loading the mower on the transport vehicle. A hot engine and exhaust system can burn you and can ignite some materials.
Turn the fuel valve to the OFF position. This will prevent carburetor flooding and reduce the possibility of fuel leakage.
If installed, remove the grass bag.
If a suitable loading ramp is not available, two people should lift the mower on and off the transport vehicle while holding the mower level.
Position the mower so all four wheels are on the bed of the transport vehicle. Tie the mower down with rope or straps, and block the wheels. Keep the tie- down rope or straps away from the controls, adjustment levers, cables, and the carburetor.
Fold the handlebar so the mower will take up less space. See “Handlebar” on page 17.

STORAGE

Proper storage preparation is essential for keeping your lawn mower trouble free and looking good. To help keep rust and corrosion from impairing your lawn mower’s function and appearance, and to make the engine easier to start after storage, follow the  instructions described in this section to:

• Drain or treat the fuel
• Change the oil and coat the engine cylinder
• Clean the mower, engine, and grass bag
• Choose a storage location

Fuel
See “AVOIDING FUEL-RELATED PROBLEMS” on page 20 for a list of recommended procedures to avoid fuel related problems.
The DISTRIBUTOR’S LIMITED WARRANTY (page 22) does not cover fuel system damage or engine performance problems resulting from neglected storage preparation.
Cleaning
Mower Deck
Allow the engine to cool before washing.
Before washing the underside of the mower deck, stop the engine and turn the fuel valve to the OFF position. Rest the mower on its right side, so the fuel cap side is up. This will help to prevent fuel leakage and hard starting due to carburetor flooding. Wear  heavy gloves to protect your hands from the blades.
Be careful to avoid getting water into controls and cables.
Engine
Allow the engine to cool, and then wash the engine by hand. Be careful to prevent water from entering the air cleaner and exhaust opening.
Using a garden hose or pressure washing equipment can force water into the air filter. Water in the air cleaner will soak the paper element and can enter the carburetor or engine cylinder, causing damage.
Water contacting a hot engine can cause damage. If the engine has been running, allow it to cool before washing.

Grass Bag
Remove the bag from the mower, and wash it with a garden hose or pressure washer. Allow the bag to dry completely before storage.
Drying
After washing the lawn mower, wipe dry all accessible surfaces.
Place the mower with its wheels on a level surface. Start the engine outdoors and let it run until it reaches normal operating temperature to evaporate any water remaining on the engine.
Stop the engine and allow it to cool.
After the lawn mower is clean and dry, touch up any damaged paint, and coat other areas that may rust with a light film of oil.

Oil
Change the engine oil (page 13) if planned storage is 3 months or longer or when storing in a high humidity environment.
Add oil in the engine cylinder to prevent corrosion.

1. Remove the spark plug (page 14).
2. Pour ateaspoon (5 cc) of clean engine oil into the cylinder to keep it from rusting.
3. Pull the starter rope several times to distribute the oil in the cylinder.
4. Reinstall the spark plug.
5. Pull the starter rope slowly until resistance is felt, and then return the starter grip gently.
   This will close the valves so moisture cannot enter the engine cylinder.

Storage Location
If your mower will be stored with gasoline in the fuel tank and carburetor, it is important to reduce the hazard of gasoline vapor ignition. Select a well- ventilated dry storage area away from any appliance that operates with a flame, such as a furnace, water heater, or clothes dryer. Also avoid any area with a spark-producing electric motor, or where power tools are operated.
Make sure the fuel valve is in the OFF position to reduce the possibility of fuel leakage.
Place the mower with its wheels on a level surface. Tilting can cause fuel or oil leakage.
With the engine and exhaust system cool, cover the mower to keep out dust. A hot engine and exhaust system can ignite or melt some materials. Do not use sheet plastic as a dust cover. A nonporous cover will trap moisture around the mower, promoting rust and  corrosion.

Handlebar
Remove the grass bag if installed. You can place it on top of the engine with the bag opening to the front.

1. Tumn the handlebar adjust knobs 90 degrees to unlock the locating pins @.
2. Fold the handlebar forward ®; do not pinch or kink the cables.
   Move the blade control lever slightly to allow it to clear the engine when folding.

Removing From Storage
‘When unfolding the handlebar, be sure to lock the handlebar adjust knobs to secure the handlebar in the mowing position.
Check your mower as described in “BEFORE EACH OPERATION” on page 4.
If the cylinder was coated with oil during storage preparation, the engine may smoke briefly at startup.

TROUBLESHOOTING

Engine Will Not Start

•  Cut a narrower swath
•  Use a slower ground speed
•  Cut more frequently
Grass is too wet| Allow the grass to dry
Mower deck is clogged| Clean out the mower deck (page 16).
Air filter is clogged| Clean or replace the air filter (page 13).
Bad fuel; mower stored without treating gasoline, or refueled with bad gasoline| Refuel with fresh gasoline (page 7).
Fuel filter clogged, carburetor malfunction, ignition malfunction, valves stuck, etc.| Take the mower to an authorized Honda servicing dealer for repair.

Loss of Power

•  Cut a narrower swath
•  Use a slower ground speed
•  Cut more frequently
Grass is too wet| Allow the grass to dry
Mower deck is clogged| Clean out the mower deck (page 16).
Air filter is clogged| Clean or replace the air filter (page 13).
Bad fuel; mower stored without treating gasoline, or refueled with bad gasoline| Refuel with fresh gasoline (page 7).
Fuel filter clogged, carburetor malfunction, ignition malfunction, valves stuck, etc.| Take the mower to an authorized Honda servicing dealer for repair.

Vibration

16).
Blades loose| Tighten loose blade bolts (page 12).
Blades bent, damaged, or unbalanced by improper sharpening| Take the mower to an authorized Honda servicing dealer for repair.
Mechanical damage, such as a bent crankshaft

Mowing and Bagging Problems

toward MIN position (page 8), or push the Select Drive lever less.
Cutting height adjustment levers set at different positions| Set all levers at the same cutting height position (page 6).
Grass bag clogged| Wash the grass bag (page 16).
Mower deck is clogged| Clean out the mower deck (page 16).
Grass is too tall| •  Raise the cutting height
•  Cut a narrower swath
•  Use a slower ground speed
•  Cut more frequently
Grass is too wet| Allow the grass to dry.
Blades dull, worn, or damaged| Sharpen or replace the blades if necessary (page 12).
Wrong blades installed| Install correct blades (page 12).

TECHNICAL INFORMATION

Serial Number Locations

There are two serial numbers, one for the engine (located below the fuel valve) and one for the mower frame. Record the engine and frame serial numbers in the space below. You will need these serial numbers when ordering parts and when making technical or warranty inquiries.
Engine serial number:
Frame serial number:
Date of purchase:___

High Altitude Operation
At high altitudes, the standard carburetor air-fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard starting.
Operation at an Altitude that differs from that at which this engine was certified, for extended periods of time, may increase emissions.
High altitude performance can be improved by specific modifications to the carburetor. If you always operate your lawn mower at altitudes above 2,000 feet (610 meters), have your servicing dealer perform this carburetor modification. This engine, when operated at high altitude with the  carburetor modifications for high altitude use, will meet each emission standard throughout its useful life.
Even with carburetor modification, engine horsepower will decrease about 3.5% for each 1,000-foot (300-meter) increase in altitude. The effect of altitude on horsepower will be greater than this if no carburetor modification is made.

NOTICE
When the carburetor has been modified for high altitude operation, the air- fuel mixture will be too lean for low altitude use. Operation at altitudes below 2,000 feet (610 meters) with a modified carburetor may cause the engine to overheat and result in serious engine damage. For use at low  altitudes, have your servicing dealer return the carburetor to original factory specifications.

Emission Control System
Source of Emissions
The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they 18 react to form photochemical smog when subjected to sunlight. Carbon monoxide does not  react in the same way, but it is toxic.
Honda utilizes appropriate air/fuel ratios and other emissions control systems to reduce the emissions of carbon monoxide, oxides of nitrogen, and hydrocarbons. Additionally, Honda fuel systems utilize components and control technologies to reduce evaporative emissions.

U.S. and California Clean Air Acts, and Environment and Climate Change Canada (ECCC)
U.S. EPA, California and Canadian regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emissions control systems.
The following instructions and procedures must be followed in order to keep the emissions from your Honda engine within the emissions standards.

Tampering and Altering
NOTICE
Tampering is a violation of federal and California law.
Tampering with or altering the emissions control system may increase emissions beyond the legal limit. Among those acts that constitute tampering are:

• Removal or alteration of any part of the intake, fuel, or exhaust systems
• Alterations that would cause the engine to operate outside its design parameters

Problems That May Affect Emissions
If you are aware of any of the following symptoms, have your engine inspected and repaired by your authorized Honda Power Equipment dealer

• Hard starting or stalling after starting.
• Roughidle.
• Misfiring or backfiring under load.
• Afterburning (backfiring).
• Black exhaust smoke or high fuel consumption.

Replacement Parts
The emissions control systems on your new Honda engine were designed, built, and certified to conform with EPA, California (models certified for sale in California only), and Canadian emissions regulations. We recommend the use of Honda Genuine parts whenever you have maintenance  done. These original-design replacement parts are manufactured to the same standards as the original parts, so you can be confident of their performance. Honda cannot deny coverage under the emission warranty solely for the use of non-Honda replacement parts or service performed at a  location other than an authorized Honda dealership; you may use comparable parts certified by the EPA, CARB or ECCC, as applicable, and have service performed at non-Honda locations. However, the use of replacement parts that are not of the original design and quality may impair the  effectiveness of your emissions control system.
A manufacturer of an aftermarket part assumes the responsibility that the part will not adversely affect emissions performance. The manufacturer or rebuilder of the part must certify that use of the part will not result in a failure of the engine to comply with emissions regulations.
Maintenance
As the power equipment engine owner, you are responsible for completing all required maintenance listed in your owner’s manual.
Honda recommends that you retain all receipts covering maintenance on your power equipment engine, but Honda cannot deny warranty coverage solely for the lack of receipts or for your failure to ensure that all scheduled maintenance has been completed.

Follow the Maintenance Schedule on page 11. Remember that this schedule is based on the assumption that your Honda engine product will be used for its designed purpose. Sustained high-load or high-temperature operation, or use in dusty conditions, will require more frequent service.

Air Index
(Models certified for sale in California)
An Air Index Information label is applied to engines certified to an emission durability ime period in accordance with the requirements of the California Air Resources Board.
The bar graph is intended to provide you, our customer, the ability to compare the emissions performance of available engines. The lower the Air Index, the less pollution.
The durability description is intended to provide you with information relating to the engine’s emission durability period. The descriptive term indicates the useful life period for the engine’s emission control system. See your EMISSION SYSTEM WARRANTY (page 23) for additional  information.

125 hours (greater than 80 cc)
Intermediate| 125 hours (0 ~ 80 cc)
250 hours (greater than 80 cc)
Extended| 300 hours (0 ~ 80 cc)
500 hours (greater than 80 cc)
1000 hours (225 cc and greater)

Specifications
Mower Features

HRX217K6VLAA HRX217K6VLPA| Honda rotary mower, 21-inch mower deck, Clip Director, Select Drive variable speed transmission, Auto Choke System, self- charging electric start
---|---

Dimensions and Weights

*1-1/4 inch (32 mm) cutting height and handle in highest position
** Includes the grass bag

Engine Design and Performance

(0 ~ 1.78 m/s)

Maintenance

Fuel| Unleaded gasoline with a pump octane rating of 86 or higher containing no more than 10% ethanol by volume
Capacity: 0.24 US gal (0.91 L) See “AVOIDING FUEL-RELATED PROBLEMS” on page 20| page 7
---|---|---
Blade Bolt Torque| 36 ~ 43 ft-lb (49 ~ 59 N•m)| page 12
Engine Oil| SAE 10W-30, API SJ or later Capacity: 13.5 oz (0.40 L)
Refill amount: 12.0 ~ 13.5 oz  (0.35 ~ 0.40 L)*| page 13
Spark Plug| Type: NGK – BPR5ES
Gap: 0.028 ~ 0.031 in (0.7 ~ 0.8 mm)| page 14
Select Drive Cable| Adjust for proper operation.| page 15
Maximum Governed Speed| 2,950 ~ 3,100 rpm **| Shop manual
Valve clearance (cold)| Intake: 0.10 ± 0.02 mm
Exhaust: 0.10 ± 0.02 mm| Shop manual

• Actual amount will vary due to residual oil in the engine. Always use the dipstick to confirm the actual level (page 6).
  ** Do not try to increase the engine speed above the maximum governed speed; the blades could fracture and come apart.

AVOIDING FUEL-RELATED PROBLEMS

When properly maintained, your Honda lawn mower should provide years of trouble-free operation. This includes the fuel system. However, gasoline can quickly deteriorate (in as little as 30 days) causing starting or running problems and, in some cases, damage to the fuel system.
Most fuel-related problems can be avoided by following the precautions listed below. Fuel system damage and engine performance problems resulting from deteriorated gasoline are not covered by the Distributor’s Limited Warranty (see page 22).

Follow These Precautions to Prevent Most Fuel-Related Problems

Do not use gasoline containing more than 10% ethanol (E10). Not all automotive gasoline is safe to use in your lawn mower.| Higher levels of ethanol in gasoline attract water, and can corrode or damage the fuel system and cause performance problems.
Store gasoline in a clean, plastic, sealed container approved for fuel storage.
Store your fuel supply container away from direct sunlight; if the  container has a vent, keep it closed.| A plastic container eliminates the risk of rust and metallic  contaminants from a metal container entering the fuel system. Gasoline will deteriorate faster when exposed to air and sunlight.
Purchase only enough gasoline to last for 1 to 2 months (about 30 to 60 days).
If you purchase enough gasoline to last for more than 60 days, add a fuel stabilizer to your storage container when you fill it.| Gasoline deteriorates with age so try to avoid storing it for long  periods, especially in summer heat.
Fuel stabilizer will extend the shelf life of gasoline, but it will not reconstitute stale fuel.
Keep your lawn mower’s fuel tank full of fresh fuel when not in use. Turn the fuel valve OFF.| If the fuel tank is only partially filled, air in the tank will promote fuel deterioration.
Keep the air filter clean and properly serviced. Check it before each use.| A properly maintained air filter will help prevent dirt from entering the carburetor. The small passages inside the carburetor can become blocked.
1 to 3 Months Before Next Use| Reason
---|---
If you did not add fuel stabilizer to your fuel storage container when you filled it up, fill your lawn mower’s fuel tank with fresh gasoline.| If the fuel tank is only partially filled, air in the tank will promote fuel deterioration.
Add fuel stabilizer to the lawn mower’s fuel tank according to the stabilizer manufacturer’s instructions.| Fuel stabilizer will extend the life of gasoline, but it will not reconstitute stale gasoline.
Run the engine outdoors for 10 minutes.| This makes sure treated gasoline has replaced untreated gasoline throughout the fuel system.
Turn the fuel valve to the OFF position, start the engine, and let it run approximately 3 minutes until the carburetor is empty and the engine stops.| The small amount of gasoline in your engine’s carburetor will deteriorate faster than the fuel in the fuel tank due to its small volume and heat from the engine.
More Than 3 Months Before Next Use| Reason
---|---
Start the engine and let it run long enough to empty all the gasoline from the entire fuel system, including the fuel tank.
Do not allow gasoline to remain in your lawn mower’s fuel tank  for more than 3 months (about 90 days) of inactivity.| Al fuel stabilizers have a shelf life. It is good practice to empty the
fuel system for long term inactivity.

‘We recommend Pro Honda Fuel Stabilizer, that has improved formulation with added corrosion protection (page 21).

CUSTOMER INFORMATION

Parts, Accessories, and Service Items
Contact an authorized Honda servicing dealer to purchase any of these (or other) Honda Genuine items for your lawn mower.

Replacement Parts

38206-V15-003

Spare key| 35111-VL0-W01|

Accessories

with ID mark
Mower deck guard kit| 06761-VH7-000AH| Two stainless steel side guards
Battery charger| 06320-VH7-UA2| Float style charger with adapter
Lawn mower cover| 08P59-VE2-000AH| Custom fitted, waterproof, and breathable

Service ltems

SAE 10W-30

engine oil

| 08207-10W30| 1 quart
NO-SPILL gas

cans

| See your local dealer| 1-1/4 gallon
See your local dealer| 2-1/2 gallon
Fuel stabilizer| 08732-0800| 8 ounces

For short and long term storage

® NO-SPILL is a registered trademark of NoSpill LLC.

Dealer Locator Information
To find an Authorized Honda Servicing Dealer anywhere in the United States, visit powerequipment.honda.com and click on Find a Dealer.
How to Contact Honda
Honda Power Equipment dealership personnel are trained professionals. They should be able to answer any question you may have. If you encounter a problem that your dealer does not solve to your satisfaction, please discuss it with the dealership’s management.
The Service Manager or General Manager can help. Almost all problems are solved in this way.
If you are dissatisfied with the decision made by the dealership’s management, contact the Honda Power Equipment Customer Relations Office. You can write:

American Honda Motor Co., Inc.
Power Equipment Division
Customer Relations Office
4900 Marconi Drive
Alpharetta, GA 30005-8847

Or telephone: 770-497-6400
M-F, 9:00 a.m. – 7:30 p.m. ET
When you write or call, please give us this information.

• Model and serial numbers (page 18)
• Name of the dealer who sold the lawn mower to you
• Name and address of the dealer who services your lawn mower
• Date of purchase
• Your name, address, and telephone number
• Adetailed description of the problem

Honda Publications
These publications will give you information for maintaining and repairing your lawn mower.
Owner’s Manual
Keep this owner’s manual handy so you can refer to it at any time. Consider this owner’s manual a permanent part of the lawn mower; please give it to the new owner if you resell the lawn mower.
The information and specifications included in this publication were in effect at the time of approval for printing. American Honda Motor Co.,
Inc. reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission.
Shop Manual
This manual covers complete maintenance and overhaul procedures.
It is intended to be used by a skilled technician. Available for purchase by visiting publications.powerequipment.honda.com.
Parts Catalog
This manual provides complete, illustrated parts lists for your mower.
Visit powerequipment.honda.com and then click on Support for free online access to parts catalog. It is also available for purchase in paper form by visiting publications.powerequipment.honda.com.

Frequently Asked Questions

The Honda Power Equipment web site provides additional information for users of Honda power equipment. Visit powerequipment.honda.com and click on FAQs or scan the QR code shown.

DISTRIBUTOR’S LIMITED WARRANTY

Honda Power Equipment
This warranty is limited to the following Honda Power Equipment product when distributed by American Honda Motor Co., Inc., Power Sports and Products Division, 4900 Marconi Drive, Alpharetta, Georgia 30005. The following warranty applies to products manufactured on or after April  1, 2023.

PRODUCTS COVERED BY THIS WARRANTY| LENGTH OF WARRANTY (1)
(from date of original retail purchase)
---|---
PRIVATE RESIDENTIAL(2)| COMMERCIAL/RENTAL/ INSTITUTIONAL
HRX Mower| 60 months| 3 months

1. Length of Warranty: Batteries supplied with applicable products as standard, original equipment are covered by this warranty for a period of 12 months (private residential) or 3 months (commercialirentaliinstitutional use) from the date of original reail product purchase.
2. Private residential: Used in maintaining owner’s primary and/or secondary residence.
   Any other use, including but not limited to informal *for hire” use, is considered commercialrentalinstitutional use.

To Qualify for This Warranty:
The product must be purchased in the United States, Puerto Rico, or the U.S. Virgin Islands from American Honda or a dealer authorized by American Honda to sell those products. This warranty applies to first retail purchaser and each subsequent owner during the applicable warranty time  period, unless noted otherwise.
What American Honda Will Repair or Replace Under Warranty:
American Honda will repair or replace, at its option, any part that is proven to be defective in material or workmanship under normal use during the applicable warranty time period. Warranty repairs and replacements will be made without charge for parts or labor. Anything replaced under  warranty becomes the property of American Honda Motor Co., Inc. All parts replaced under warranty will be considered as part of the original product, and any warranty on those parts will expire coincident with the original product warranty.
To Obtain Warranty Service:
You must, at your expense, take the Honda Power Equipment product, accessory, replacement part, apparel, or the power equipment on which the accessory or replacement part is instailed, and proof of purchase to any Honda Power Equipment dealer in the United States, Puerto Rico, or  the U.S. Virgin Islands who is authorized to sell and/or service that product, during the dealer’s nomal business hours. To locate a dealer near you, visit our web site at_ http://powerequipmenthonda.com and click on Find a Dealer.
If you are unable to obtain warranty service or are dissatisfied with the warranty service you receive, contact the owner of the dealership involved; nomally this will resolve the problem. However, if you should require further assistance, write or call the Power Equipment Customer Relations  Department of American Honda Motor Co., Inc. See “How to Contact Honda’ on page 21

Exclusions:

1. Any damage or deterioration resulting from the following:
   – Neglect of the periodic maintenance as specified in this manual
   – Improper repair or maintenance
   – Operating methods other than those indicated in the product owner’s manual Increasing engine speed beyond factory specification
   – The use of non-genuine Honda parts, accessories, lubricants, and fluids other than those approved by Honda Exposure of the product to soot and smoke, chemical agents, bird droppings, sea water, salt or other corrosive environments – Collision, fuel contamination or deterioration,  neglect, unauthorized alteration, misuse, incorporation or use of unsuitable attachments or parts
   – Normal Wear and tear (including, but not limited to, normal fading of painted or plated surfaces, sheet peeling, and other natural deterioration)

2. Consumable parts: Honda does not warrant parts deterioration due to normal wear and tear. The following parts are not covered by this warranty unless they are needed during another repair covered under this warranty: spark plug, fuel filter, air cleaner element, dutch disc, tire,  wheel bearing, recoil starter rope, cable, belt, cutter blade, oil, and grease.

3. Cleaning, adjustment, and normal periodic maintenance work (carburetor cleaning, engine oil draining, blade sharpening, beft and cable adjustments)

4. Any product that has ever been dedlared a total loss o sold for salvage by a financial institution or insurer

5. Auger and paddle assemblies, skid shoes, and scraper bars of snow throwers/snow blowers, tiller tines of roto-fillers, and mower blades and mower deck housings are specifically not warranted against impact damage including, but not limited to, abrasive damage.

Disclaimer of Consequential Damage and Limitation of Implied Warranties:
American Honda disclaims any responsibility for loss of time or use of the product, transportation, commercial loss, or any other incidental or consequential damage Any implied warranties are limited to the duration of this written limited warranty.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, therefore the above exclusions and limitations may not apply to you. This warranty gives you specific legal rights, and you may  also have other rights, which vary from state to state

Honda Parts, Accessories, and Apparel
This warranty is limited to Honda Power Equipment parts, accessories, and apparel when distributed by American Honda Motor Co., Inc., 4900 Marconi Drive, Alpharetta, Georgia 30005-8847.

PRODUCTS COVERED BY THIS WARRANTY

| LENGTH OF WARRANTY
(from date of original retail purchase)
---|---
PRIVATE RESIDENTIAL|

COMMERCIAL/RENTAL/ INSTITUTIONAL

Parts| 6 months| 3 months
Battery| 6 months| 3 months
Accessories| 12 months| 3 months
Apparel| 6 months| 3 months

To Qualify for This Warranty:
The parts, accessories, or apparel must be purchased from American Honda or a dealer authorized by American Honda to sell those products in the United States, Puerto Rico, and the U.S. Virgin Islands. Parts and Accessories must be purchased for installation on original Honda equipment  or engines to be eligible for warranty coverage. Installing parts and accessories on non-Honda products or engines voids this warranty.
‘You must be the first retail purchaser. This warranty is not transferable to subsequent owners.
What American Honda Will Repair or Replace Under Warranty:
American Honda will repair or replace, atits option, any Honda Power Equipment parts, accessories, replacement parts, or apparel that are proven to be defective in material or workmanship under normal use during the applicable warranty time period. Anything replaced under warranty  becomes the property of American Honda Motor Co,, Inc. The warranty on all parts, accessories, and apparel replaced under warranty will expire coincident with the original warranty on the replaced parts, accessories, or apparel Parts and accessories installed by a dealer who is authorized  by American Honda to sell them will be repaired or replaced under warranty without charge for parts or labor. If installed by anyone else, parts and accessories will be repaired or replaced under warranty without charge for parts, but any labor charges will be the responsibilty of the  purchaser.
Apparel will be repaired or replaced under warranty without any charge.
To Obtain Warranty Service:
You must, at your expense, take the Honda Power Equipment part, accessory, apparel or the Honda Power Equipment on which the part or accessory is installed, and proof of purchase to any Honda Power Equipment dealer i the United States, Puerto Rico, or the U.S. Virgin Islands who is  authorized to sell that product, during the dealer’s normal business hours. To locate a dealer near you, visit our web site at PowerEquipmentHonda.com and click on Find a Dealer. If you are unable to obtain warranty service or are dissatisfied with the warrant  sefvice you receive, contact the  owner of the dealership involved; normally this will resolve the problem. However, if you should require further assistance, write or call the Power Equipment Customer Relations Department of American Honda Motor Co., Inc. See “How to Contact Honda” on page 21
Exclusions:
This warranty does not extend to parts, accessories, or apparel affected or damaged by collision, normal wear, use in an application for which the product was not designed or any other misuse, neglect, incorporation or use of unsuitable attachments or parts, unauthorized alteration,  improper installation, or any causes other than defects in material or workmanship of the product. Installing parts and accessories on non-Honda products or engines voids this warranty.
Disclaimer of Consequential Damage and Limitation of Implied Warranties:
American Honda disclaims any responsibility for loss of time or use of the product, or the power equipment on which the product is installed, transportation, commercial loss, or any other incidental or consequential damage. Any implied warranties are limited to the duration of this written warranty. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exdusion or limitation of incidental or consequential damages, so the above exdusions and limitations may not apply to you This warranty gives you specific legal rights, and you  may also have other rights which vary from state to state.
PWL50623-Y

EMISSION CONTROL SYSTEM WARRANTY

Your new Honda Power Equipment engine complies with the U.S. EPA, Environment Canada, and State of Calfornia (models certified for sale in California_only) emission regulations. American Honda Motor Co., Inc.
provides the emission warranty coverage for engines in the United States and its teritories. Honda Canada Inc. provides the emission warranty for engines in the 13 provinces and territories of Canada. In the remainder of this Emission Control System Warranty, American Honda Motor Co.,  Inc. and Honda Canada Inc. wil be referred to as Honda.
CALIFORNIA EXHAUST AND EVAPORATIVE EMISSIONS CONTROL WARRANTY STATEMENT ‘YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and Honda are pleased to explain the exhaust and evaporative emissions (“emissions”) control system warranty on your 2023 and later Honda Power Equipment engine. In Califomia, new equipment that use small off-road engines must be designed, built,  and equipped to meet the State’s stringent anti-smog standards. Honda must warrant the emissions control system on your power equipment engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off-road engine or  equipment leading to the failure of the emissions control system Your emissions control system may include parts such as the carburetor or fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid fuel and fuel vapors), fuel caps, valves, canisters, filters,  clamps and other associated components. Also included may be hoses, belts, connectors, and other emission-related assemblies (see the adjacent column for additional covered parts)
Where a warrantable condition exists, Honda will repair your power equipment engine at no cost to you including diagnosis, parts and abor.
MANUFACTURER’S WARRANTY COVERAGE:
The exhaust and evaporative emissions control system on your Honda power equipment engine is warranted for two years. If any emissions-related part on your Honda power equipment engine is defective, the part will be repaired or replaced by Honda

OWNER’S WARRANTY RESPONSIBILITY:

• As the power equipment engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual.
  Honda recommends that you retain all receipts covering maintenance on your power equipment engine, but Honda cannot deny warranty coverage solely for the lack of receipts o for your failure to ensure the performance of all scheduled maintenance.

• As the power equipment engine owner, you should however be aware that Honda may deny you warranty coverage if your power equipment engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications

• You are responsible for presenting your power equipment engine to a Honda Power Equipment servicing dealer as soon as the problem exists.
  The warranty repairs shall be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your emission warranty rights and responsibilities, you should contact the Honda office in your region

American Honda Motor Co., Inc.
Power Equipment
Customer Relations
4900 Marconi Drive
Alpharetta, Georgia 30005-8847
Telephone: 888-883-3139
Email: powerequipmentemissions@ahm.honda.com

Or

Honda Canada Inc.
Power Equipment Customer
Relations
180 Honda Bivd
Markham, ON, L6C 0H9
Telephone: 888-946-6329

YOUR WARRANTY RIGHTS AND OBLIGATIONS
Other States, U.S. territories, and Canada:
In other areas of the United States and in Canada, your engine must be designed, built, and equipped to meet the U.S. EPAand Environment Canada emission standards for spark-ignited engines at or below 19 kilowatts Specific Honda products that do not meet the California emissions  regulations can be identified by a “Califomia: Not for sale or use” or “California: Only for use in Farming or Construction Equipment” decal
All of the United States and Canada:
The exhaust and evaporative emissions control system on your Honda power equipment engine sold in the United States and Canada is warranted for two years from the date of delivery to the ultimate purchaser or the length of the Honda Distributor’s Limited Warranty, whichever is longer.  This warranty is transferable to each subsequent purchaser for the duration of the warranty period
If any emissions-related part on your Honda power equipment engine is defective, the part will be repaired or replaced by Honda. All defective parts

replaced under this warranty become the property of Honda. Only Honda approved replacement parts may be used in the performance of any warranty repairs and must be provided without charge to the owner. A list of warranted parts is shown in the table below. All emission related parts  are under warranty for the remainder of the warranty period. Normal maintenance items, such as spark plugs and filters, that are on the warranted parts list are warranted up to their required replacement interval only.
Honda will also replace other engine components damaged by a failure of any warranted part during the warranty period. Honda cannot deny coverage under the emission warranty solely for use of non-Honda replacement parts or service performed at a location other than an authorized  Honda dealership; however, use of a part that is not functionally identical to the original equipment part in any respect that may in any way affect emissions (including durability) could result in denial of coverage. If such a non-Honda replacement part is used in the repair or maintenance of  your engine, and an authorized Honda dealer determines it is defective or causes a failure of a warranted part, your claim for repair of your engine may be denied. If the part in question is not related to the reason your engine requires repair, your claim will not be denied

TO OBTAIN WARRANTY SERVICE:
You must, at your own expense, take your Honda Power Equipment engine or the produict on which it is installed, along with your sales registration card or other proof of original purchase date, to any Honda Power Equipment dealer who s authorized by Honda to sell and service that  Honda product during their normal business hours. Claims for repair or adjustment found to be caused solely by defects in material or workmanship will not be denied because the engine was not properly maintained and used If you are unable to obtain emission warranty service or are  dissatisfied with the warranty service you received, contact the owner of the dealership involved. Normally this should resolve your problem. However, if you require further assistance, contact the Honda office in your region using the information shown in the adjacent column.

EXCLUSIONS:
Failures other than those resulting from defects in material or workmanship are not covered by this warranty. This warranty does not extend to emission control systems or parts that are affected or damaged by owner abuse, neglect, improper maintenance, or unapproved modifications.
This warranty does not cover replacement of expendable maintenance items made in connection with required maintenance service after the item’s first scheduled replacement as listed in the maintenance section of the product owner’s manual, such as: spark plugs and filters.
DISCLAIMER OF CONSEQUENTIAL DAMAGE AND LIMITATION OF IMPLIED WARRANTIES:
American Honda Motor Co., Inc. and Honda Canada Inc. disclaim any responsibility for incidental or consequential damages such as loss of time or the use of the power equipment, or any commercial loss due to the failure of the equipment, and any implied warranties are limited to the  duration of this written warranty. This warranty is applicable only where the Califomia, U.S. EPA, or Environment Canada emission control system warranty regulation is in effect

EMISSION CONTROL SYSTEM WARRANTY PARTS:

SYSTEMS COVERED BY THIS WARRANTY:

|

PARTS DESCRIPTION:

---|---
Fuel Metering| Carburetor assembly (includes starting enrichment system), Oxygen sensor, Throttle body, Engine temperature sensor, Engine control module, Fuel injector, Fuel regulator, Intake manifold
Evaporative| Fuel tank, Fuel cap, Fuel lines (for liquid and fuel vapors), Carbon canister, Canister mounting brackets, Fuel line fittings, Fuel strainer, Fuel valve, Fuel pump, Fuel hose joint, Canister purge port connector
Exhaust| Catalyst, Exhaust pipe, Muffler (with catalyst), Exhaust manifold
Air Induction| Air cleaner case, Air cleaner element
Ignition| Flywheel comp., Flywheel magneto, Ignition pulse generator, Crankshaft position sensor, Power coil, Ignition coil assembly, Ignition control module, Spark plug cap, Spark plug
Crankcase Emission Control| Crankcase breather tube, Breather valve assembly, Oil filler cap
Miscellaneous Parts| Tubing, fittings, seals, gaskets, and clamps associated with these listed systems.

• Covered up to the first required replacement only. See the “Maintenance Schedule” on page 11
  PWL50975-X

NOTES

PRODUCT REGISTRATION

Thank you for choosing Honda. To ensure you receive important service information in the event of a product update or recall, please register your lawn mower within 30 days of purchase.
From time to time, American Honda conducts sales promotions that require you to register your lawn mower within 30 days of purchase. If you purchased your Honda lawn mower during one of these promotions, you must register your mower within 30 days.
Your information will remain confidential. It will not be released to any other company or organization.
Failure to register your lawn mower does not diminish your warranty rights.
Please complete and mail the postage paid card, scan the QR code, or register online at powerequipment.honda.com/reg as shown on the next page.

Scan this QR code to register your lawn mower.

Register Your Product Online

1. Go to powerequipment.honda.com/reg to register your unit.
2. Enter your serial number, and then click Submit.
3. Complete the required information and click Submit. It’s that simple!

BUSINESS REPLY MAIL
FIRST-CLASS MAIL PERMIT NO. 117 ALPHARETTA GA
POSTAGE WILL BE PAID BY ADDRESSEE
Power Equipment Division
American Honda Motor Co., Inc.
4900 Marconi Dr
Alpharetta GA 30005-9956

NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES

References

• Honda Power Products Parts - Parts look up and information
• Honda Power Products Support Publications | Official Site | Honda Power Products Support Publications

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>