CRPP-UW62 Dls Cruise Installation Guide
- June 15, 2024
- DLS
Table of Contents
CRPP-UW62 Dls Cruise
Product Information
Welcome to DLS! Thank you for buying a DLS Cruise CRPP-UW64. This woofer is designed and sound-tuned in Sweden by DLS Sweden, a part of Winn Scandinavia AB. DLS is dedicated to providing high-quality sound and construction. The CRPP-UW64 is a universal 4 ohm woofer that is engineered to deliver optimal sound performance in your vehicle.
Product Usage Instructions
Pre Installation:
Before starting the installation, disconnect and secure the negative terminal
from your battery/power source to prevent any risk of damage.
Installation:
General Installation:
- Mount the speakers in the door or rear shelf of your car.
- If the factory pre-made mounting holes do not fit, you may need to modify the fitting.
- To improve sound reinforcement, you can use a baffle made of MDF-board or similar material.
- For door placements, use speaker rings to ensure a proper fit to the door panel.
- Ensure that the speakers are securely fastened to avoid bad sound or rattling.
Custom Baffle Installation:
When installing a custom baffle, follow the correct way shown in the provided
diagrams. Chamfered edges are recommended, and the maximum thickness of the
baffle should be 5 mm.
Speaker Connection:
- Ensure that the cables are connected with correct polarity on the speaker terminals.
- Observe the markings and size differences on the connectors to ensure proper connection.
Speaker Phasing:
To check if the CRPP-UW64 woofer is using the correct polarity (phase) after
installation, you can easily perform a test using a 1.5 volt battery.
Running-in Time:
Allow the speakers to run-in for a period of time to achieve optimal
performance. The exact running-in time is not specified in the manual.
DLS Support:
If you require any further assistance or support with your DLS Cruise CRPP-
UW64 woofer, please contact DLS support for help.
Specifications:
The specifications for the CRPP-UW64 woofer are provided in the manual. Please
refer to page 5 for detailed information on dimensions, impedance vs
frequency, and product markings.
Warranty:
This speaker is covered by warranty, subject to the conditions in the country
where it is sold. If you need to return the speaker for service, please
include the original dated receipt with the product.
Declaration of Conformity:
The DLS Cruise speakers for vehicles are manufactured in accordance with the
EU directive EEC 95/54 (72/245/ EEC) and are marked with the approval number.
They are also marked in accordance with the WEEE-directive 2012/19/EC and the
EU RoHS directive 2015/863/EU.
Welcome to DLS!
Thank you for buying a DLS Cruise CRPP-UW64. For us, it’s all about the sound
experience. We care deeply about sound and construction quality. In order for
your experience to be as optimal as possible, it is important that you read
this manual, preferably before you start your installation. Keep the manual in
a safe and accessible place for future reference.
Your speakers must be installed correctly in order to work as intended. Make sure you have all necessary tools nearby before starting and that you are completely confident in how to process. If you feel the slightest uncertainty; feel free to take the help of an experienced installer or a car audio dealer.
Warranty
This speaker is covered by warranty, depending on the conditions in the country where it is sold. If the speaker is returned for service, please include the original dated receipt with the product.
General
Some sound systems may vary in size of the door speaker. Make sure that your
vehicle has the same size as this speaker, before you start the assembly
DECLARATION OF CONFORMITY
DLS Cruise speakers for vehicles are manufactu-red in accordance with the EU
directive EEC 95/54 (72/245/ EEC) and are marked with the approval number.
They are also marked in accordance with the WEEE-directive 2012/19/EC. The
products are also produced in accordance with the EU RoHS directive
2015/863/EU.
Included parts
Included products:
- 2pcs Woofers
Included in box:
- 8pcs M4 screws
- 4pcs Fork terminals
- 4pcs Flat pin connectors
- 1pc PRY tool
- 1pc Manual
Pre installation
Disconnect Battery
- Before you start the process of replacing speakers, disconnect and secure the negative terminal from your battery/power source. This will prevent the risk of damaging yourself or the products.
- Place the disconnected terminal in a secure and isolated location away from any possible connection belonging to the battery/power source system.
Installation
General installation
Mount the speakers in the door or in the rear shelf of your car. They may fit
in the factory pre-made mounting holes, if not you might have to modify the
fitting. If you want to improve the sound reinforcement you can use a baffle
of MDF-board or similar. For door placements, there are normally speaker rings
that have to be used to make the speaker fit to the door panel.
NOTE!
It is important to fasten the speakers properly in order to avoid bad sound or
rattling.
Custom baffle installation
It is very important that the custom baffle are stable and fasten properly,
but it is just as important that it´s shaped in a way that the driver is
allowed to “breathe” correctly. Bass reproduc-tion will be enhanced when the
air flow is free and not obstructed.
Speaker connection
Make sure you connect the cables with correct polarity on the speaker terminals. Observe the markings and size differences on the connectors.
Speaker phasing
- To be sure that the CRPP-UW64 woofer are using the correct polarity (phase) after installation, it is possible to check this easily by using a 1.5 volt battery.
- Connect the battery’s positive and negative pole to the speaker cable. If the speaker is correctly connected the cone should move outwards. This need to be tested on all left/ right pairs to make sure all drivers are in phase with each other.
Note!
Don´t use this testing method on tweeters or other low excursion drivers
without a correct connected high pass crossover.
Crossover settings
DLS recommend using active crossover settings for the UW64 speaker to get
increased power handling and durability.
- High pass filter: 60-100 Hz
- Low pass filter: 3500-5000Hz
Door insulation
- DLS recommends using insulation and/or sound deadening in the car doors. It lowers the noise from the road/tires and prevent rattles and other noises from plastic details in the doors.
- If you need help deciding what type of door insulation you should use, ask your DLS distributor for info and guidance.
Running-in time
- Allow the tweeters to play for at least 15-20 hours in order to perform at its possibly best. This run-in can be made with tone sweep or with just music.
- Start at a moderate volume and increase the volume step by step during the running in period. After the 15-20 hour run in session the performance and char- acteristics will be in the correct condition.
DLS support
For technical assistance, ask your car audio dealer where the product was sold or the dis- tributor in your country. You can always contact DLS Helpdesk in Sweden at e-mail: info@dls.se. Information can also be found on our WEB-site www.dls.se. We follow a policy of continuous advancement in development. For this reason, all or part of specifications and designs may be changed without prior notice.
Wiring diagram
Specifications
Art. no/CD-CRPP-UW64
- Woofer 6.5” / 165mm
- RMS Power 100W
- MAX Power 200W
- Impedance 4 Ohm
- Sensitivity 86.8dB 1W/1M
- Freq. range 55-5000Hz
Technical specifications
- Voice coil size 1” / 25mm
- Voice coil material Copper voice coil / Kapton® former
- Basket Euro-DIN ventilated reinforced steel frame
- Magnet High grade ferrite / Ventilated back plate
- Cone Laminated glass fibre cone
- Dust cap Santoprene® rubber dust cap
- Spider Nomex® with woven tinsel leads
- Terminal Twin terminal
Electro-Acoustic Parameters
- Re 3.2 Ohm
- Fs 63.2Hz
- Mms 15.8gr
- Cms 0.399
- Vas 10.9L
- Qts 0.66
- Qes 0.89
- Qms 2.512
- Bl 4.74T.m
- SPL 86.8dB 1W/1M
- Sd 139cm 2
Dimensions
Impedance VS Frequency
Product markings
- The crossed-out wheelie bin symbol means that the product, literature and packaging included must be taken to separate collection at the end of their working life. Do not dispose of these products as unsorted municipal waste: take them for recycling. For info on your nearest recycling point, check with your local waste authority.
- This product has been granted with the CE certification mark to show that the product follows the health, safety, and environmental protection standards for products sold within the European Economic Area (EEA).
- DLS products complies with the relevant provisions of the RoHS Directive for the European Union. In common with all Electrical and Electronic Equipment (EEE) the product should not be disposed of as household waste. Alternative arrangements may apply in other jurisdictions.
- DLS is a global partner of the European Mobile Media Association, an organisation that focus on promoting the custom made mobile media installations to consumers.
We follow a policy of continuous advancement in development. For this reason all or part of specifications & designs may be changed without prior notice. We reserve for possible typos, factual or numeric errors that may have been printed on any products, package designs, user manuals and/or other included accessories.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>