BOYO VTC700AI-4 AI AHD Monitor and Cameras System Installation Guide

: June 15, 2024
: BOYO

Table of Contents

System Accessories
Installations
Wiring
Monitor Buttons
Remote Control Buttons
Setting, Configuration and Calibration
Menu
Specification
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VTC700AI-4
7″ AI AHD Monitor & Cameras BOYO VTC700AI 4 AI AHD Monitor and Cameras
System System (4 Channel)
Installation Guide

Please read all instructions carefully before using, and keep the manual for future reference.

System Accessories

Product Features:

7″ AI monitor to detect vehicles and pedestrians
4 Cameras included for front view, rear view, left-side and right-side views
Warning Beeps when an object is detected in an alarm zone
Built-in DVR
1 x 65ft video extension and 3 x 33ft video extension included

Before Installation:

Please check contents.
Perform bench test. Ensure the product is working before installation by connecting the monitor and the camera to 12-24VDC.
Perform pre-install test, before mounting the monitor and the cameras.
Position the camera and verify the view on the monitor before mounting.
For recording, please use the high speed C10 class memory card.
No repairable components inside. If not working, please request a part replacement.

Installations

Positioning the monitor and cameras.
The cameras should point toward the blind spots or not easily viewable positions.
The monitor should be placed where it is clearly visible from the driver without any objects obstructing the view. At the same time. the monitor must not block driver’s view of the road or surroundings.
An example camera positions:

LCD Monitor
Front Camera
Backup Camera
Left Camera
Right Camera

Monitor Installation
a. Install the monitor bracket using the 3 self-tapping screws.

Screw in the center.
Adjust the angle.
Tighten all screws. b. Install the monitor using 2 bolts on each sided.
Do not tighten bolts. c. Adjust the monitor angle.
Tighten all bolts.

Camera Installation
a. The camera is mounted on the left and right sides

Rotate camera body for the best position.
Tighten screws to fix camera.
b. The camera is mounted for front and rear
Adjust the best position up and down.
Tighten screws to fix camera.

Memory Card Installation

Wiring

Connect to reverse trigger (e.g. backup light)
Connect to left trigger (e.g. the left turn signal)
Connect to right trigger (e.g. right turn signal)
The role of the trigger is to display specific camera. Let us suppose that the monitor is set to display the rear-view camera while driving. If the right is triggered by turning on the right turn signal, the monitor will display the right-side camera in full screen. When the right turn signal is turned off, the right-side camera display is turned off and the rear-view camera is displayed.

Monitor Buttons

Operation: The system is operated using the buttons on the monitor or using a remote control BOYO VTC700AI 4 AI AHD Monitor and Cameras System -
Buttons

Remote Control Buttons

BOYO VTC700AI 4 AI AHD Monitor and Cameras System -
Remote

Setting, Configuration and Calibration

When a menu button is pressed, the menu bar appears at the bottom of the screen. 2022-01-05 15:27
Time icon

| Recording icon: red dot flashing in recording status
---|---
| Recording icon: Recording status is on
| SD card icon: SD memory card working status
| Red Trapezoidal area: Blind zone alarm area
| Green rectangular area: Traffic detected
| Blue rectangle area: Pedestrian detected

Press Menu button to enter and you will see five menu icons on screen: Time, Display, BSD Smart Drive, View Files and System setting.7.1 Time
To get to the Time setting, using up, down and OK button to choose your settings, and press Menu button to back to main interface. 7.2 Display
The default value of Brightness, contrast and saturation is 50, The Brightness, contrast and saturation value is between 0-100,
7.3 BSD Smart Drive

| Calibrate: Blind zone alarm range setting
---|---
| Turn on/off the blind spot alarm
| Setting: Alarm tone on/off, sensitivity setting(high, mid, low)

7.3-1 Blind Zone Warning Calibration(left, right, front, back) The red point is the current adjustment angle,choosing to remove the position of red spot, choosing to toggle next setting corner, after setting, click save and exit.
Left blind spot alarm calibration Right blind spotalarm calibrationFront & back blind spot alarm calibration7.3-2 BSD Setting
Single Alarm Sound on / off
Four Alarm Sound on / off
Alarm Sensity: Low/Medium/High selection7.4 Video Playback
Click the main menu video playback button to enter the playback menu, choose and view the video file, and swipe up and down in the video file to browse all the single-screen video files.7.5 System Setting

Keytone	ON/ OFF	Button touch sound
Record mute	ON/ OFF	Audio recording
Loop record	1/2 minutes	1 or 2 min. video clips
Backlight	High/ Mid/ Low	Screen brightness
Video watermark	ON/ OFF	Watermarks can be used for authentication
Volume setting	0/1/2/3/4	Voice prompt volume
Front camera mirror	ON / OFF
Trigger delay	off / 3s / 6s / 9s	Without a delay the display will coincide

with trigger on and off. Note: if the left-side camera trigger is connected to the left turn signal, the left camera display will blink synchronously with the left turn signal light. User should set the turn signal time delay to 3 seconds or more.
Screen sleep| OFF/ lOs / 30s/ 60s| Screen saver mode
Interval record| OFF/ 1H / 12H/ 24H| Even if ignition power is off, the monitor will continue to record by compressed video format, lfps for 1 second recording
About Device| Software version number|
Reversing line| OFF/ Mode 1 / Model 2/Model 3| Show or hide parking guidelines
Language| English/Japanese/ Korean/Spanish/French| Select display language
Reset Factory| YES / ON| Reset all setting to factory default
Format storage| YES / ON| Erase the memory card

Specification

Monitor Specification

Screen type| 7″ IPS TFT LCD
Aspect Ratio| 16:09
Active Pixels| 1280(V) x RGB x 720(H)
Resolution (RGB)| 1024 x 600
Brightness| 500cd/m2
Viewing angle| 85/85/85/85(UR/U/D)
Operating Voltage| DC12V – 24V
Power| 6W
Video Format| H.264
Video System| AHD 720 PAU NTSC
Response Time(ms)| 25ms (typ.) (Tr+Tf)
Recording Storage| 128G
Operation Temperature| -4°F ∼ 158°F
Spanish French| English/Korean/Japanese Spanish/French
Video input| 4 Channel, AV1/AV2 /AV3/AV4
Blind Zone Alarm Max Distance| 20 feet
Camera Specification

WARRANTYINFORMATION
This one year limited warranty is given to the end-user or the retail purchaser (referred to this warranty as “Original Purchaser”) that it will be free from defects in materialand workmanship for a period of one year from the date of the purchase of the new product (excluding accessory items such as power cords,cradle,memory card,adaptor,and cables).
This limited warranty does not cover any physical damage to, or misuse of, this product, damage caused by improper installation;improper use;misuse; neglect; repair of cracked scratched, broken or modified cosmetics; or parts that have been altered or removed: damages done by another device used with this product resulting from use of non BOYo brand parts. This warranty is VOID if you purchased this product as used,floor model sample, or refurbished; if the product has been altered or modified in any way (including but not limited to attempted repair without authorization from BOYO-Vision Tech America, Inc.and/or alterationremoval of the serial number).
For warranty information, visit: https://visiontechamerica.com/pages/get- support

For technical support: Call: (888)941-3060
Email: info@visiontechamerica.com
Visit: www.VisionTechAmerica.com