AquaAmp AA-02-CIR Wireless Charger Instruction Manual
- June 5, 2024
- AquaAmp
Table of Contents
AquaAmp AA-02-CIR Wireless Charger
Overview
The product must be installed according to the specified instructions. Failure
to comply may result in personal injury, vessel/vehicle damage, and/or product
failure. Installation by a trained electrician is recommended by AquaAmp.
Damage and/or injuries caused by improper installation are not covered by the
warranty.
WARNING
Only a 12V DC or 24V DC battery/power supply should be used with this device. Before installing, the power supply must be turned off. Between the battery/power supply and the product, an appropriate fuse or circuit breaker must be utilized. Before turning on the electricity, double-check that al wiring is polarized correctly. High voltages may be included in this product. Do not alter the product in any way. This product is not intended for use in potentially hazardous or flammable environments. Do not install in a hazardous/flammable environment, such as engine rooms. Make sure the spacebehind the mounting point is clear of wires, fuel, and any other potentially hazardous things before drilling any holes. Ensure that any holes cut do not considerably degrade the surface’s structure. If the product must be installed outside, it must be installed safely above the waterline and not in danger of being submerged. |A metallic surface prevents the product from charging.The item is designed to charge Qi-compatible devices only. The cable must be kept in place and not obstruct mechanical systems. There are no user- serviceable components in this product. In no way attempt to repair or modify the product. The device’s high friction top surface does not guarantee that it will not slip during strong acceleration and deceleration working situations. A phone case thicker than 3mm may prevent the smartphone from charging. The product may temporarily shut down if used in a hot environment or in direct sunlight; this is a safetyy feature of the electronics. The IP rating is only valid if the instructions are followed correctly. Avoid mounting near heat- radiating appliances and in poorly ventilated spaces when choosing a placement.
EMC INSTALLATION GUIDELINES:
To ensure that electromagnetic interference between equipment is minimized,
AquaAmp devices comply with Electromagnetic Compatibility (EMC) requirements.
To keep electromagnetic interference to a bare minimum, proper installation is
essential.
WIRING:
When extending the wire from your battery/power source to the product, make
sure there is a continuous supply of at least 10V. For any length of cable
extension, we recommend an 18AWG (0.82mm2) wire gauge. This diagram shows how
the product should be linked to a 12V or 24V DC battery or power supply.
IMPORTANT:
AquaAmp LLC disclaims all liability for any injuries or other damages resulting from the use of their products in any situation.
WARRANTY
The non-transferable 2-year warranty covers only this AquaAmp product and not any devices mounted unknown hazard at their u ie y a gu e, ala ey SuDject them to known and in o hazards at their own tib unknown cause, harmful interference and (2) this dovice much act S nis devIce may not undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to This equipment has been tested and found to comply with the limits tor a lass B digital device, pursuant to part 15 of the FCC Hules, Ihese limits are designed to provide reasonable protection against harmful interference ina residential installation. Ihiss may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between tne equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to hich the receiver is connected.
- Consult the dealer or an experienced radiov technician to help.
FCC RF exposure statement.
The equipment complies with FC radiation exposure limits set torth tor an uncontrolled environment. The equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body. FCC ID: 2A54NAA-01-SUB