UsoGood TC30 Trail Camera User Manual
- June 12, 2024
- Usogood
Table of Contents
UsoGood TC30 Trail Camera
We are ready to help you solve your problem, please contact our support team to get 1 year free replacement and lifetime technical support! Please contact email: support@usogood.co
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving an tenna.
Increase the separation between the equipment and receiver. Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Package List
Please carefully unpack camera and check that below accessories are contained in the box. If any parts are missing, please contact us via email support@usogood.co
- Wildlife Camera x 1
- Mounting Belt x 1
- Instruction Manual x 1
- Type-C cable x 1
- Batteryx8
- SD Card x1
Functional Features
It is a high-definition wildlife camera, which supports night vision, has rainproof capability and can work automatically outdoors all day long. When people or animals intrude into the field of camera view, the camera will automatically take photos or videos. If no people or animals trigger it, it will be in standby mode. It is widely used in animal tracking, hunting, farm monitoring and other scenarios.
- ON/TEST/OFF
- LCD
- Lens
- IRLED
- MENU
- UP
- Lock ring
- USB interface
- DOWN
- OK
- SD card slot
- MODE
- PIR
- DC INPUT
- Tripod mounting hole
Get Started
Insert the memory card
The camera uses CLASS 6 or above TF card(up to 32GB), please format the memory
card on the computer and install it as shown in the figure:
- Open the panel lock
- insert the memory card
Notice:
Turn off the camera before removing or inserting the memory card, otherwise
the memory card may be damaged or data may be lost.
Install the battery
The camera uses Bx 1.SV AA batteries or 1.SV rechargeable batteries for power
supply, please install the batteries as shown in the figure: Switch the
[Function] to’TEST’, the screen will light up, indicating that the battery is
installed correctly.
Notice:
Insert batteries in the specified direction, and do not mix old and new
batteries. After installation, the lock must be fastened.
Using an external power supply
To ensure long working hours, the camera can use an external power supply. The
DC-IN interface are as shown in the figure:
Notice:
Please use a standard external power supply: DC 6V/2.0A, 3.5mm interface. The
wrong external power supply can damage the camera. Do not remove the internal
battery when using an external power source. When the external power supply is
not used, the waterproof plug must be covered.
Detecting the PIR Sensors
Insert 8x 1.SV AA batteries and a formatted memory card, switch to ‘TEST’mode,
waving your hand in front of the camera lens, If the red light is flashing, it
indicates the side PIR sensors are working properly and the if green light is
flashing, it indicates the main PIR sensor is also working properly.
Press OK button to take a photo manually. Then press MODE button to check the
photo you have taken. If it succeedes, it indicates the camera works well.
Setup the Camera
- Insert the formatted SD card
- Insert 8 brand new 1.SV AA batteries
- Switch to TEST mode
- Press MENU to set parameters
- Place the camera on a suitable placement
- Switch to ON mode
- The camera works after Ss countdown
Note: After Ss countdown, the screen will turn black. At this time, please wait another 30s to activate the internal analog circuit, during this time the camera does not take pictures.
Scan the QR code to learn how to operate the camera
Install the Camera
Notice:
- The detection range of the pir sensors is 120°. Please aim the main sensor at the capture zone to ensure that no movement is missed.
- To ensure that the camera does not unnecessarily record irrelevant action, please avoid direct sunlight.
Main Functions
Cycle storage
Turn on the cycle storage function, when the memory card is full, it will be
automatically overwritten.
Target recording time
Turn on the Target recording time, set the working time, the camera will only
work during the set period. Please note that the Time Lapse function should be
turned off at this time.
Time lapse
Turning on Time lapse, the camera takes photos at regular intervals and
automatically creates a video file. Please note that the Target recording time
function should be turned off at this time.
PIR Interval
After the selected interval, only when the animal enters the detection range,
the camera will be triggered and take a picture. Shorter intervals and higher
camera frequency will consume power faster.
Switch to ‘ON’ mode then wait for the 5 seconds countdown to enter the working
mode. If you can take pictures or record videos normally with this setting,
the camera is working properly.
Note: The camera will experience a PIR interval (depends on your settings) when it just enters the working mode, it will not take a photo during this time.
Technical
UsoGood Service
When you receive our products, please contact us if you encounter any problem
during installation or use.
If any problem is found, please contact us.
Email: support@usogood.co
Website: usogood.co
We promise you can choose one of them
- 24-hour technical support
- Repair products for free
- Trade-in of products used for more than 2 years
Warranty
Amazon only offers 1 month free returns, Contact us to extend the warranty to 12 months!Scan the QR code below to extend the warranty:
Register within 10 days after receiving your camera to ensure your purchase is
100% guaranteed.
All we need is your order details … That’s it! Register on line NOW!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>