Ikan PT4500 15 Inch Teleprompter Tripod and Dolly Turnkey User Guide

Ikan PT4500 15 Inch Teleprompter Tripod and Dolly Turnkey

OVERVIEW

Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera setup. This solution includes a 15” teleprompter, tripod, and dolly. All of our systems have been tested internally for payload compatibility.

The remaining payload capacity, after mounting the full 15” teleprompter system without the counterweight, can accommodate camera setups up to 25.2 lbs. The tripod, without the teleprompter system, can accommodate cameras up to 44.1 lbs. This solution also includes a carrying bag for the tripod.

PT4500
15” High Bright Beam Splitter Teleprompter

What’s Included

• 1 x Teleprompter Base
• 1 x Bracket with Glass
• 1 x Teleprompter Hood with Boot
• 1 x Monitor
• 1 x AC Adapter with Cord
• 1 x Prompter Pro Software
• 1 x Counterweight Set (2 x 2.5 lbs)
• 2 x D-Ring ¼-20” Screws
• 2 x Hex Keys
• 3 x Different Height Risers

Teleprompter Assembly Setup

Step 1
Place the teleprompter glass frame on a flat surface and remove the four screws as shown.

Step 2
Align and attach the teleprompter hood with the 8 screw pegs from the teleprompter frame.

Step 3
The metal frame is directional. Make sure the thicker side is on top and the slimmer side is on the bottom.

Step 4
Put the washers on before tightening the screws. The washers and 4 additional screws are inside a bag on the bottom foam.

Step 5
Extend the teleprompter hood open and attach teleprompter boot using the clips. It is suggested to align the seam with the bottom of the teleprompter hood.

Step 6
Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods.

Step 7
Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.

Step 8
After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.
Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.

• SAFETY NOTE * Make sure to leave at least 2 inches of the rods inside the teleprompter base.

Step 9
While sliding the teleprompter bracket into the slot of the teleprompter base pull on the red knob to allow the bracket to fully slide in.

Step 10
Once the bracket is in place, tighten the side screw to lock in place. Double check and make sure all the screws are tightened with the included hex keys.

Step 11 (optional)
Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.

Foam Case

To make your teleprompter more portable, we packed it in a reusable, high- quality foam.
The shape and size of the foam was designed to fit into Ikan’s PT-CASE-V2.

Monitor Ports

BNC – AV Composite Input
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v Input

HDMI – Switch HDMI input
VGA – Switch to VGA input
AV – Switch to composite BNC input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting

Monitor Menu Settings

Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit

How to set-up FLIP button feature:

1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both Horizontal and Vertical flip

Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters

https://youtu.be/5TjIxzBc_Vc

Specifications

PT4500

Optional Accessories

PT4500-G Replacement Glass for both PT4500 / PT4700
PT15-HB-V2 15” High Bright Monitor (for PT4500)
PT17-HB-V2 17” High Bright Monitor (for PT4700)
PT-CASE-V2 Rolling Hard Case for PT4500/PT4700 Teleprompter

Learn More

More dynamic information at official website: www.ikancorp.com

Support

Contact email: support@ikancorp.com

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.

*Free Service will not be Provided in the Following Situations:(Even if the product is still within the warranty period.)**

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

GA102 100mm Aluminum Video Tripod

The GA102 two stage aluminum tripod supports a payload weighing up to 132 lbs. It is made of lightweight aluminum, has a 100mm bowl, and the legs are a twin tube design with two stages. The tripod can be adjusted to a maximum height of 63” and a minimum height of 18” with a folded length of 29”. The mono-lock feature allows for quick height adjustments of both stages with one twist. An adjustable floor spreader provides extra security and stability.

FEATURES

100mm

160.0cm 63.0in

47.0cm 18.5in

74.0cm 29.1in

60.0kg 132.0lbs

5.1kg 11.2lbs

Aluminum

3

stages With Mono-lock Patent Design

Mono-lock design allows you to lock and unlock the three sections of each leg using only one locking lever quicker than normal.

  FEATURES

100mm Bowl Size

Compatible with all professional 100mm half-ball video heads.

Extendable Ground Spreader

Extendable spreader is designed to offer added stability to the tripod.

Removable Rubber Feet

Removable feet attach to the spiked feet for working on delicate or hard surfaces.

GH20 100mm Fluid Head

Dimension

FEATURES

Fixed drag of pan & tilt

Longer sliding plate

Leveling bubble

8 plus 0 steps of counterbalance

  SPECIFICATIONS

| Model| GH20
---|---|---
| Payload Range| 20.0kg/ 44.0lbs
| Counterbalance Range| 0-8
| Grades Of Pan Drag| Fixed
| Grades Of Tilt Drag| Fixed
| Tilt Range| -60°/+90°
| Temperature Range| -30℃~+60℃
| Bowl Size| 100mm
| Net Weight| 3.5kg / 7.7lbs

VIDEO TRIPOD

VIDEO TRIPOD SYSTEM

Dollies Manual

Packing list

In order to provide quick and smooth movement for the tripods, E-IMAGE supplies kinds of dollies, with different payload super study. Individually braked wheels; some with cable guards. Folds for easy transporting.

In The Box

Let’s take El-7004 for example

El-7004 X1

User Guide

Prepare The Dolly

Pull the knob or press the lock pin, slowly open the dolly leg until the pin hits the leg fixing hole. If the leg is opened abruptly, fingers can get caught and cause injury. Check that all lock pins are through the leg fixing holes.

Individual

El-7ooanooacnoo4noo4enoo4c

1. Caster lock lever
2. Carrying handle
3. Leg band
4. Tripod leg holder
5. Leg fixing hole
6. Locking slider
7. Knob to adjust the position of the Locking slider
8. Knob to adjust the lock lever for the tripod foot
9. Caster

El-7oosnoosenoosnoo7

1. Caster lock lever
2. Carrying handle
3. Position knob
4. Leg band
5. Tripod fixing hole
6. Leg fixing hole
7. Column entrance
8. Caster
9. Cable guard lock knob
10. Cable guard

El-7003 & 7003C

El-7003 & 7003C

Using

1. Pull the knob to extend the dolly. Steer Mode.
   This operation suitable for El-7003, El-7003C.

2. Step on the independent brakes for locking the dolly in position.
   When moving the dolly under unlocking the brake pistoled the tripod or pedestal with your hand during operation.
   This operation suitable for all E-IMAGE dollies.

3. Attach the tripod or pedestal to the dolly .Please remove the camera from the tripod or pedestal before assemble the tripod to the dolly. Make sure that the leg bands at three positions are securely fixed.
   This operation suitable for all E-IMAGE dollies.
   

4. Loose the knob in the anticlockwise direction to adjust the position of the locking slider.

El-7003C is a professional universal tripod dolly which comes with fully adjustable leg locks to fit almost all full-sized tripods.

5. Unlock the casters when moving the dolly. Hold and control the tripod or pedestal with your hand during operation.

El-7004 & 7004B

.0in

El-7004C

1. Rotate the knob in the anticlockwise direction to extend the dolly.
   

2. Loose the knob in the anticlockwise direction to adjust the height of the cable guard.
   This operation suitable for El-7004B dolly.

3. Loose the knob in the anticlockwise direction to adjust the position of the locking slider.
   

4. Loose the knob in the anticlockwise direction to adjust the position of the locking slider.
   El-7004C is a professional universal tripod dolly which comes with fully adjustable leg locks to fit almost all full-sized tripods.
   

El-7005 & 7005B

1. Press the locking pin to release and extend the dollies.
   This operation suitable for El-7005,7005B,7006,70
   

El-7006 & 7007

/ 4.0in
El-7007| 10.7kg     /23 .61bs| 100cm      /39 .4in| 100kg     /220 .51bs| 125m m / 5.0in

1. Lower angel shooting with any 100mm heads.
   This operation Suitable for El-700
   

2. Rotate the knob in anticlockwise direction to fix into different holes to achieve directional movement.
   This operation suitable for El-7007.
   

3. Loose the knob in the anticlockwise direction to adjust the height of the cable guard.
   This operation suitable for El-7007 dolly.
   

Customer Information

Sales Manager

Service

Service Result:  ☐Solved    ☐Unsolved  ☐Refunded/ Replaced

Contents are subject to change without prior notice, you can download the latest version from www.eimagevideo.com.

References

• Professional Video Production Equipment for Sale | Ikan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>