Blackview AirBuds 60 Bluetooth Headphones User Guide

Blackview AirBuds 60 Bluetooth Headphones User Guide

PRODUCT INTRODUCTION

DEVICE CONNECTION

Method 1: 1. When using the product for the first time, open the charging box cover. The headset indicator light flashes white, and the headset enters “pairing status”.

2. Turn the Bluetooth on, and select “AirBuds 60”. There is a connection prompt tone after successful connection.

Method 2:

1. When the headset is connected to the device, click the “Touch” button four The white light flashes and the headset will enter the pairing state (cannot operate during calls or playing music).
2. Turn on Bluetooth and select “AirBuds 60”. There will be a connection prompt after the connection is successful.

Note: The above is the connection method when the product is pairing a new device for the first time. After the initial use of the product, the earbuds will automatically switch on and connect to the device when you take it out from the charging case.

CONTROL

1. Power on: Open the charging case, and the headphones will automatically power
2. Shut down: Put the headphones into the charging case and close the charging case to shut down .
3. Restore factory settings:

(In pairing mode)Double touch + long press 5S; when the white light flashes for 3 times, the headphones will enter the factory reset mode, put the headphones into the charging case, the headphones status will be restored to the factory settings .You can open the cover to re-pair.

ii) Playback Mode

iii) Call Mode

Light indication

TECHNICAL SPECIFICATIONS

Earbuds driver

• 10 mm neodymium magnet sound Units x 2

Frequency Response

• 20–20,000 Hz

Microphone

• Omnidirectional MEMS x1 (per earbud)

Bluetooth Version

• Bluetooth 3

Bluetooth profile

• A2DP
• AVRCP
• HFP

Audio Codec

• SBC AAC

Wireless operating frequency

• 2402-2480 MHz

Wireless transmission range

• Up to 10 meters (measured in open area). Walls and wall structures may affect the transmission range of the

Playback time

• Up to 7 hours on a single full charge
• Total playback time: 30 hours^

Battery

• Earbuds: Rechargeable lithium-ion

Polymer Battery 3.7 V 40 mAh 0.148 Wh

• Charging case: Rechargeable lithium-ion

Polymer 3.7 V 500 mAh

1.85 Wh

Charging time

• ≈ 2 hours

IP Rating

• IPX7 waterproof

Operating temperature

• 0-45°C

Maximum output power

• 5 dBm

Input rated power

• 5V 1A

^Based on moderate volume. Actual battery life will vary, depending on specific use, settings, and environmental factors

NOTE: Compliance markings are in the charging case.

CAUTION: Do not use the earbud at a high volume for extended periods of time as this may cause hearing loss

Answers for Common Questions

• The bluetooth headset cannot be switched Reason: The battery in the charging compartment is low or the power of the bluetooth headset is low.

Solution: Put the headset into the charging box, close the cover, and charge the charging box for more than 1 hour before use.

• The phone cannot search for bluetooth Reason: 1. The Bluetooth headset is not in the pairing state; Solution: When the headset is connected to the device, click the Touch button four times. The indicator light will flash white and the headset will enter pairing status.

Reason: 2. There are mobile phone bluetooth program errors;

Solution: After the bluetooth of the mobile phone is restarted, clear all pairing data stored in the the mobile phone; Search for bluetooth again.

• There is no sound from the headset speaker Reason: Turn the volume of the mobile phone and

headset to the maximum and conf irm whether it is caused by volume adjustment.

Solution: When the headset is connected, adjust the volume of the mobile phone;

Reason: 2. The Bluetooth headset is not properly connected with the mobile phone.

Solution: Reconnect bluetooth and mobile phone through pairing.

Reason: 3. The Bluetooth headset is not within the valid working range.

Solution: Keep the headset within 10 meters of the mobile phone, and there are no large objects, walls and other obstacles between the headset and the device.

(4)  The headset doesn’t send messages or the voice is low.

Reason: 1. The Bluetooth headset is too far from the mouth; Solution: The bluetooth headset should be worn on the ear for normal use;

Reason: 2. The microphone hole of Bluetooth is blocked or water has entered;

Solution: Remove the blockage of the microphone hole or prevent water from entering the microphone hole.

(5)  The headphone get stuck or disconnected when talking or listening to

music.

Reason: 1. The Bluetooth headset is too far away from the mobile phone or there are obstacles.
Solution: 1. Keep the headset within 10 meters of the mobile phone, and there are no large objects and walls between the headset and the device. Be careful not to cover the bluetooth headset with your hand. In order to maintain the continuous stability of the signal, please try to keep the bluetooth and the mobile phone in the same direction.
Reason: 2. There is a problem with the bluetooth signal of the mobile phone or there is strong signal interference nearby.
Solution: It is best not to make the mobile phone close to metal objects. You can also change another mobile

phone or try another place.

Reason: 3. The power of bluetooth headset is insuff icient. Please charge the headset as soon as possible.
Solution: Please charge the headset as soon as possible.
There is no sound in the headset during voice call, and the sound comes out of the mobile Reason: The headset is operated during a voice call or call. Double click the headset.
Solution: Turn off the bluetooth of the mobile phone and then turn it on, or put the headset into the box, close the cover, turn off the headset and then open the cover; The headset does not support the connection or hanging up of voice calls. If there is a voice call, please connect or hang up on the mobile phone.(Note: at present,the headset only supports incoming calls from GSM cards, not app network calls.)

(7)  After the headset is put into the box and the cover is closed, the

headset is not disconnected.

Reason: 1. The charging box is completely dead; Solution: Charge the charging box;
Reason: 2. The headset is not put into the box properly, and the communication between the headset and the base is abnormal.
Solution: Re-open the charging box, take the earphones out of the charging box and put them in the charging box. When the earphones are put into the charging box, the charging column on the charging box lights up, and the charging box cover is closed.
Reason: 3. The charging box is damaged.
Solution: Replace the charging box.

Attention

• Please do not disassemble this product by
• Please use standard charging cable and adapter to avoid damage and
• Please aviod using corrosive cleaning detergent to clean this
• Please avoid product usage in the rain and keep away from heating or f

Maintenance

Please follow the following suggestions to prolong product working life.

• Keep product dry and don’t put in damp places in case of affecting internal
• Aviod product usage during intense sporting or on sweating occasions in case sweat infiltrate into product and cause
• Keep off sunlight or high temperature in case of shortening working life of electric parts battery damage, plastic parts
• Keep off intense vibration and impact from hard material in case of internal circuit

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>