Blackview AirBuds 5 Pro Bluetooth Earphone User Guide

Blackview AirBuds 5 Pro Bluetooth Earphone

Follow Blackview community, a place where you can share and discuss with Blackview user keep posted with most up-to-day news

Product Introduction

Device Connection

First Pairing

1. Open the cover and two earbuds are in the charging box, long press the button of the charging box for 2 s until the Indicator tight nickers while and the earbuds enters a state of pairing.
2. Tum on the Bluetooth on the device and select Air8uds 5 Pro·; click and connect it successfully, and there is a voice broadcast of connection prompt tone . Remark: The device Is first paired In the above method; Later, the earbuds can be automatically tumed on and connected without the need for pairing.

Specifications

• Model: Alr8uds 5 Pro
• Bluetooth Version: 5,0
• Battery Type: Polymer Lithium Battery
• Bluetooth Effective Distance: 10m
• Bluetooth Frequency: 2.4GHz
• Bluetooth Transmitted Modulation: GFSK, n/4-DQPSK, 8DPSK
• Dynamic Driver: 7mm
• Dynamic Frequency Response: 20Hz-20KHz
• Battery Capacity(Charging Box) : 480mAh
• Charging Time(Charging Box): <1.Sh
• Charging Time(Earbuds): <1.5h
• The Broadcast Time: 24H

Operation Method

OpenNoih

Reduction Mode

| double click on the left

earbud 10scrol l

| NA
Regular Mode| NA
Answer Cal| NA| Double click t o answer

i n calling state

End Call| NA| Double click **end**

in call **status**

Reject Call| NA| NA
Voice Assistant| Triple dick| Triple dick

Charging in Charging Box

The Earbuds can be charged in Charging Box through Type-C interface, and yellow light will be on when the Earbuds are being charged; the Earbuds are charged after the box Is covered, and green light will be on when the Earbuds are fully charged,

Indication of LED

Timoout SUlnl  dbywboflno

deV10eis connected

| ****

No light

Bluetooth Pairing| While light next to the button

breathing for120 s

Connected| Breathing LightOff
Battery Low| The red fight next to the

open button is on for 7s

Put headphone In Charging Box| 1, 0•15%-Red l gt,1 – 2S

2, 15%-90%   –  orange light 2S

3, 90%•1 00%-  green light  2S

RemowHeadphone from

ChargingBox

Charging Box. Charging| yellow light next to the

charging,g pott always on

Charging Box fully Charged

| Green light next to Iha

charging port always   on

Answers for common questions

1. Bluetooth headset cannot be turned on,
   Reason: The battery of the Bluetooth headset is low or dead.
   solution: Put the earphones in the charging case, close the cover and charge them for more than 1 hour\ before turning on the earphones,

2. The phone cannot search for the Bluetooth &arphones,
   Reason: The headphone is not turned on or pair&d with low battery.
   solution : Close the cover to charge or long press the base for 2 s to pair.

3. No sound from earphones speakers,
   Reason: 1. The mobile phone volume is inappropriate. e.g. the volume has been adjusted to the minimum.
   Reason: 2. The Bluetooth headset is not property connect&d to the mobile phone.
   Reason: 3. The Bluetooth headset is not within the limited working range.
   Solution: 1, Adjust the phone volume,
   Solution: 2, The Bluetooth and mobile phone are pair&d and connected again.
   Solution: 3. Please make sure that the mobile phone and earphones are used within 10 meters, meanwhile there are no obstacles.

4. The earphone cannot convey the voice or the voice is very low,
   Reason: 1. The Bluetooth headset is too far away from the mouth.
   Reason: 2. The Bluetooth microphone hole is blocked or water has entered.
   Solution: 1, The Bluetooth headset should be worn on the ear for normal use.
   Solution: 2. Remove the blockage of the microphone hole or prevent water from entering tt.

5. The headset Is laggy or disconnected when talking or listening to music.
   Reason: 1, The Bluetooth headset is low on power, please charge them as soon as possible,
   Reason: 2. The Bluetooth headset is too far away from the phone or there are obstacles.
   Reason: 3. There is a problem with the Bluetooth signal of the mobile phone.
   Reason: 4. There is strong signal interference nearby.
   Solution: 1. The Bluetooth headset is as dose to the phone as possible,
   Solution: 2, It is best not to place metal objects near the phone.
   Solution: 3. Try another phone or another place.
   Solution: 4. Please do not cover the Bluetooth with your hands, in order to maintain the continuous stability of the signal, in addition, please keep the Bluetooth and the phone in the same direction.

6. The headset is not disconnected after closing the earphones box.
   Reason: 1. The charging box is completely out of power.
   Reason: 2. If the headset is not put in the box correctly, It will cause abnormal communication between the headset and the base,
   Reason: 3. The charging box is damaged.
   Solution: 1. Charge the charging box
   Solution: 2. Reopen the cover of the charging box, remove the headphone, put ij in the charging box again, and close the cover after ensuring the light next to the charging box button is on for 2 s.
   Solution: 3, Replace the charging box,

Attention

• Please do not disassemble this product by yourself.
• Please use standard charging cable and adapter to avoid damage and accidents .
• Please aviod using corrosive cleaning detergent to dean this product.
• Please avoid product usage In the rain and keep away from heating or fire.

Maintenance

• Please follow the following suggestions to prolong product working life .
• Keep product dry and don’t put in damp places in case of affecting internal circuit.
• Avoid product usage during Intense sporting or on sweating occasions in case sweat infiltrate into product and cause damages.
• Keep off sunlight or high temperature in case of shortening working life of electric parts battery damage, plastic parts deformation
• Keep off intense vibration and impact from hard material In case of internal circuit damages.

FCC

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference
2. this device must accept any interference received

including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

Note: The headset FCCID is 2APMJ-AIRBUDS5PROL, because headset is too small to fixed the FCCID, so the MIC NO. fix on the charging base.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>