Blackview AirBuds 5 Pro TWS Wireless Earphones User Guide
- June 6, 2024
- Blackview
Table of Contents
AirBuds 5 Pro
USER GUIDE
https://www.blackview.hk
Follow Blackview communtiy, a place where you
can share and discuss with Blackview user
keep posted with the most up-to-day news
Product Introduction
Device Connection
First Pairing
-
Open the cover and two earbuds are in the charging box, long press the button of the charging box for 2 s until the indicator light flickers white and the earbuds enter a state of pairing.
-
Turn on the Bluetooth on the device and select “AirBuds 5 Pro’; click and connect it successfully, and there is a voice broadcast of connection prompt tone.
Remark: The device is first paired in the above method, Later, the earbuds can be automatically turned on and connected without the need for pairing.
Specifications
Model: AirBuds 5 Pro
Bluetooth Version: 5.0
Battery Type: Polymer Lithium
Battery Bluetooth Effective Distance: 10m
Bluetooth Frequency: 2.4GHz
Bluetooth Transmitted Modulation: GFSK, n/4-DOPSK, 8DPSK
Dynamic Driver: Φ7mm
Dynamic Frequency Response: 20Hz-20KHz
Battery Capacity(Charging Box): 480mAh
Charging Time(Charging Box): <1.5h
Charging Time(Earbuds): <1.5h
The Broadcast Time: 24H
Operation Method
| L Earbud| R Earbud
---|---|---
Broadcast| NA| Double dick
Song Selection| NA| Double dick
Open Noise Reduction Mode| Double click on the left earbud to scroll| NA
Regular Mode| NA
Answer Cal| NA| Double dick to answer in calling state
End C41| NA| Double tic to end incall status
Reject Call| NA| NA
Voice Assistant| Tr ple click| Triple-click
Charging in Charging Box
The Earbuds can be charged in Charging Box through Type-C interface, and yellow light will be on when the Earbuds are being charged; the Earbuds are charged after the box is covered, and green light will be on when the Earbuds are fully charged,
Indication of LED
| Headphone mode | Status |
|---|---|
| On | No light |
| Off | No light |
| Timeout standby then no device Is connected | No light |
| Blue/tooth Pairing | White light next to the button **breathing for |
120 s
Connected| Breathing Light Off
Battery Low| The red light next to the open button is on for 7 a
Put Headphone In Charging Box| 1, 0-15Y.- Rad kilt – n
2,16%-90% – Orange I9ht – 2 S 3. 90% –
100% – Green NH – 2S
Remove Headphone from
Charging Box
Charging Box-Charging| Yellow light next to the charging pod
always on
Charging Box-Fu•y Charged| Greenlight next to the charging
post always on**
Answers for common questions
(1) Bluetooth headset cannot be turned on. Reason: The battery of the
Bluetooth headset is low or dead. Solution: Put the earphones in the charging
case, close the cover and charge them for more than 1 hour before turning on
the earphones.
(2) The phone cannot search for Bluetooth earphones. Reason: The headphone is
not turned on or paired with a low battery. Solution: Close the cover to
charge or long-press the base for 2 s to pair.
(3) No sound from earphones speakers. Reason: 1. The mobile phone volume is
inappropriate. e.g. the volume has been adjusted to the minimum. Reason: 2.
The Bluetooth headset is not properly connected to the mobile phone. Reason:
3. The Bluetooth headset is not within the limited working range. Solution: 1.
Adjust the phone volume. Solution: 2. The Bluetooth and mobile phone are
paired and connected again. Solution: 3. Please make sure that the mobile
phone and earphones are used within 10 meters, meanwhile there are no
obstacles.
(4) The earphone cannot convey the voice or the voice is very low. Reason: 1.
The Bluetooth headset is too far away from the mouth. Reason: 2. The Bluetooth
microphone hole is blocked or water has entered. Solution: 1. The Bluetooth
headset should be worn on the ear for normal use. Solution: 2. Remove the
blockage of the microphone hole or prevent water from entering it.
(5) The headset is laggy or disconnected when talking or listening to music.
Reason: 1. The Bluetooth headset is low on power, please charge them as soon
as possible. Reason: 2. The Bluetooth headset is too far away from the phone
or there are obstacles. Reason: 3. There is a problem with the Bluetooth
signal of the mobile phone. Reason: 4. There is strong signal interference
nearby. Solution: 1. The Bluetooth headset is as close to the phone as
possible. Solution: 2. It is best not to place metal objects near the phone.
Solution: 3. Try another phone or another place. Solution: 4. Please do not
cover the Bluetooth with your hands, in order to maintain the continuous
stability of the signal, in addition, please keep the Bluetooth and the phone
in the same direction.
(6) The headset is not disconnected after closing the earphones box. Reason:
- The charging box is completely out of power. Reason: 2. If the headset is not put in the box correctly, it will cause abnormal communication between the headset and the base. Reason: 3. The charging box is damaged. Solution: 1. Charge the charging box Solution: 2. Reopen the cover of the charging box. remove the headphone, put it in the charging box again, and dose the cover after ensuring the light next to the charging box button is on for 2 s. Solution: 3. Replace the charging box.
Attention
- Please do not disassemble this product by yourself.
- Please use a standard charging cable and adapter to avoid damage and accidents.
- Please avoid using corrosive cleaning detergent to dean this product.
- Please avoid product usage in the rain and keep away from heating or fire.
Maintenance
Please follow the following suggestions to prolong the product’s working life.
- Keep the product dry and don’t put it in damp places in case of affects the internal circuit.
- Aviod product usage during intense sporting or on sweating occasions in case sweat infiltrate into the product and cause damages.
- Keep off sunlight or high temperature in case of shortening working life of electric parts battery damage, plastic parts deformation.
- Keep off intense vibration and impact from hard material in case of internal circuit damages.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This
device and its antenna(s) must not be co-located or operating in conjunction
with any other antenna or transmitter.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction
Note: The headset FCCID is 2APMJ-AIRBUDS5PROR because the headset is too
small to fix the MIC NO., so the MIC NO. fix on the charging base.