Ikan PT4500-TM-PEDESTAL 15 Teleprompter Pedestal and Dolly Turnkey User Guide

Quick Start Guide
PT4500-TM-PEDESTAL
15” Teleprompter, Pedestal & Dolly Turnkey w/ Talent Monitor

OVERVIEW

Ikan’s Turnkey Broadcast Solutions include everything you need for your professional camera & teleprompting setup. This solution includes a 15” teleprompter w/ talent monitor, pedestal, and dolly. All of our systems have been tested internally for payload compatibility.
The remaining payload capacity, after mounting the full 15” teleprompter system without the counterweight, can accommodate camera setups up to 13 lbs. The pedestal, without the teleprompter system, can accommodate cameras up to 35.8 lbs. This solution also includes a carrying bag for the dolly.

PT4500
15” High Bright Beam Splitter Teleprompter

What’s Included

• 1 x Teleprompter Base
• 1 x Bracket with Glass
• 1 x Teleprompter Hood with Boot
• 1 x Monitor
• 1 x AC Adapter with Cord
• 1 x PrompterPro Software
• 1 x Counterweight Set (2 x 2.5 lbs)
• 2 x D-Ring ¼-20” Screws
• 2 x Hex Keys
• 3 x Different Height Risers

Teleprompter Assmebly Setup

Step 1
Place the teleprompter glass frame on a flat surface and remove the four screws as shown.
Step 2
Align and attach the teleprompter hood with the 8 screw pegs from the teleprompter frame.

Step 3
The metal frame is directional. Make sure the thicker side is on top and the slimmer side is on the bottom.
Step 4
Put the washers on before tightening the screws. The washers and 4 additional screws are inside a bag on the bottom foam. Step 5
Extend the teleprompter hood open and attach teleprompter boot using the clips. It is suggested to align the seam with the bottom of the teleprompter hood.
Step 6
Remove the monitor mounts from the teleprompter base using the included larger 4mm hex key to loosen from the 15mm rods. Step 7
Attach the monitor mounts on the back of the monitor’s VESA compatible threads using the 4 included screws and provided 2mm hex key.

Step 8
After the monitor mounts are attached, adjust the 15mm rods to accommodate the monitor. Leave about 1 inch of room for the teleprompter bracket.
Make sure the 15mm rods go through both set of monitor mounts. Please ensure that all screws are properly tightened after inserting the monitor.
SAFETY NOTE Make sure to leave at least 2 inches of the rods inside the teleprompter base. Step 9
While sliding the teleprompter bracket into the slot of the teleprompter base pull on the red knob to allow the bracket to fully slide in.
Step 10
Once the bracket is in place, tighten the side screw to lock in place. Double check and make sure all the screws are tightened with the included hex keys.

Step 11 (optional)
Should the teleprompter be too front heavy, you can attach the included counter weight on the back of the teleprompter base.

Foam Case

To make your teleprompter more portable, we packed it in a reusable, high- quality foam.
The shape and size of the foam was designed to fit into Ikan’s PT- CASE-V2.

Monitor Ports

BNC – AV Composite Input
VGA – Video Graphics Array DE15 Connection
HDMI – High-Definition Multimedia Interface Input Connection
Power Port – 12-24v InputHDMI – Switch HDMI input
VGA – Switch to VGA input
AV – Switch to composite BNC input
Flip – Toggle image flip
(Can be set to horizontal, vertical, or both via menu)
Up Arrow – Toggle up to adjust setting
Menu – Access to monitor settings
Down Arrow – Toggle down to adjust setting

Monitor Menu Settings

Video Config
Contrast (White Level)
Brightness (Black Level)
Tint (Chroma Hue)
Chroma (Chroma Saturation)
Sharpness (Detail)
RGB Setup – Manually configure RGB
Return
System Config
Menu Duration – Set duration of how long menu stays
on screen
Video Ratio – Set screen aspect ratio 16:9 or 4:3 (4:3 is
native resolution, 16:9 will create black bars)
Flip-H – Assign toggle button to flip image horizontally
Flip-V – Assign toggle button to flip image vertically
Reset – Factory reset
Return
PC Setup (Only available for VGA)
H-Position – Adjust horizontal position
V-Position – Adjust vertical position
Auto – Monitor automatically adjust position
Return
Exit

How to set-up FLIP button feature:

1. Press MENU button
2. Navigate to SYSTEM CONFIG.
3. Navigate to FLIP-V or FLIP-H
4. Change FLIP-V and/or FLIP-H to “ON”
5. Exit MENU
6. The FLIP button should now be activated and can be pressed to mirror the image Horizontally or Vertically
7. When FLIP-H is ON, the image will flip Horizontally
8. When FLIP-V is ON, the image will flip Vertically
9. If both are ON, the FLIP button will toggle both Horizontal and Vertical flip

Watch our VIDEO TUTORIAL on how to assemble Ikan Professional Telepromopters:https://youtu.be/5TjIxzBc_Vc

Specifications

PT4500

Optional Accessories

PT15-TM / PT17-TM
Talent Monitor Add On Kit for PT4500 / PT4700

What’s Included

● 1 x Teleprompter Monitor
● 1 x Power Adapter with Cable
● 1 x VESA Monitor Mount
● 1 x 15mm Rod Adapter
● 1 x Mounting Knob| ● 4 x 10mm Screws
● 4 x 15mm Screws
● 2 x Large Screws
● 4 x Riser Washers
● 1 x Adjustable Plate
---|---

Assembly Steps

Setting Up the Talent Monitor
Using the shorter 4 x 10mm Screws, attach the VESA Monitor Mount. Make sure that the long end of the VESA Monitor Mount is pointing in the direction of the power button like the image above. Use the Mounting Knob to tighten the 15mm Rod Adapter to the VESA Monitor Mount.

Setting Up the Teleprompter Monitor (Monitor from the PT4500/PT4700)
If the mounting brackets where previously installed on the teleprompter monitor, remove those screws. Using the longer 4 x 15mm Screws and 4 x Riser Washers attaché the mounting brackets with the washers between the bracket and monitor like the image below.

Attaching the Talent Monitor
After both the talent monitor and teleprompter monitor are set up, slide the talent monitor on to the PT4500/PT4700.
WARNING We recommend at least 1 inch of rod should be left inside the teleprompter base.

Specifications

PT17-HB
17” High-Bright Teleprompter Monitor

Supported Video Signals
HDMI
720x480i & 720x480p @ 59.94, 60 Hz
720x576i & 720x576p @ 50 Hz
1280x720p @ 50, 59.94, 60 Hz
1920x1080i @ 50, 59.94, 60 Hz
1920x1080psf @ 24, 25, 29.97, 30 Hz
1920x1080p @ 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 Hz

PT15-HB
15” High Bright Teleprompter Monitor

Supported Video Signals
HDMI
720x480i & 720x480p @ 59.94, 60 Hz
720x576i & 720x576p @ 50 Hz
1280x720p @ 50, 59.94, 60 Hz
1920x1080i @ 50, 59.94, 60 Hz
1920x1080psf @ 24, 25, 29.97, 30 Hz
1920x1080p @ 23.97, 24, 25, 29.94, 30, 50, 59.94, 60 Hz

Optional Accessories
Some other products that work well with this item available from Ikan include:

Learn More
More dynamic information at official website: www.ikancorp.com
Support
Contact email: support@ikancorp.com

CONDITIONS OF WARRANTY SERVICE

• Free service for one year from the day of purchase if the problem is caused by manufacturing errors.
• The components and maintenance service fee will be charged if the warranty period is expired.

*Free Service will not be Provided in the Following Situations:(Even if the product is still within the warranty period.)**

• Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company.
• Damage caused by natural disaster, abnormal voltage, and environmental factors, etc.

The magic life in the image world
E – IMAGE

AT7903 Pedestal

GH20 100mm Fluid Head

FEATURES

SPECIFICATIONS

| Model| GH20
---|---|---
| Payload Range| 20.0kg  / 44.0lbs
| Counterbalance Range| 0-8
| Grades Of Pan Drag| Fixed
| Grades Of Tilt Drag| Fixed
| Tilt Range| -60°/+90°
| Temperature Range| -30℃~+60℃
| Bowl Size| 100mm
| Net Weight| 3.5kg / 7.7lbs

El-7004B video Dolly
Super sturdy,designed for heavy duty systems. The 100mm/4 inch wheels can be individually braked.

FEATURES

| |
---|---|---
Pull the knob to extend the dolly, easy to go out.| Height : 17cm / 6.7in Radius: 50cm / 19.7in| Casters diameter: 100mm / 3.9in.
| |
The rubber wheels are non-marring during normal use,protecting the floor surface.
Each wheel incorporates its own foot-activated brake.| Cable guards and brakes.| Supports up to 60kg of tripod, camera and accessories.

GB3 Pan bar
Telescopic pan bar for GH08L, GH10L, GH15, GH25 heads

SPECIFICATIONS

| Length range| 405-605mm / 15.9-23.8in
---|---|---
| Net weight| 385g / 0.8lbs

©2019 Ikan International. All rights reserved.www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com
because we’re filmmakers too
www.eimagevideo.com

References

• Professional Video Production Equipment for Sale | Ikan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>