dji RX32303 Video Receiver User Guide

: June 15, 2024
: DJi

Table of Contents

Disclaimer
Introduction
Mounting the WB37 Intelligent Battery
Linking
Specifications
Documents / Resources

dji RX32303 Video Receiver

Disclaimer

Carefully read this entire document and all safety and compliance guidelines provided before use.

Introduction

The DJI video receiver can receive video signals from the transmitter when connected to the video output device for remote monitoring.

Detachable Antennas
Transmit wireless signal.
Video Status Indicator
Indicates if there is a video source signal input or not. Solid green indicates input while
solid red indicates no input.
Linking Status Indicator
Shows the linking status between the receiver and transmitter.
SDI Output Port
SDI Output Port
Outputs the video source signal from the receiver.
HDMI Port (Type A)
Receives the video source input signal.
USB-C Port For device activation and firmware updates.
DC-in Port
Supplies power to the video receiver using the provided power cable.
M4 Screw Holes
To mount the battery adapter or other adapters for expansion.
Power Output Port
Supplies power to an external device.
Air Vent
Air Intake
DO NOT cover the air vent, air intake, or both sides of the battery adapter if mounted. Otherwise, the performance of the device may be affected due to overheating.
Power Button
Press once to power on. Press and hold to power off.
Display Screen
Displays the device status and menu.
Menu Dial
Turn or press the dial to select or confirm settings in the menu.
Back Button
Press to return to the previous screen of the menu.
3/8”-16 Screw Hole
1/4”-20 Screw Holes
External Power Input Port
Mount the battery adapter and compatible battery to supply power to the video receiver.

Mounting the WB37 Intelligent Battery

Mount the WB37 battery adapter to the back of the video receiver and tighten the two M4×12 screws.
Insert the WB37 battery into the battery slot and push it to the end. Make sure that the battery release button pops up, indicating the battery is firmly in place

Make sure to use the WB37 battery within the operating temperature range. DO NOT disassemble or pierce the battery in any way. Otherwise, the battery may leak, catch fire, or explode. Refer to the WB 37 Intelligent Battery Safety Guidelines for more information.

Press and hold the RELEASE button and push the battery in the opposite direction to remove it.

Linking

Power on the video receiver. Press and hold the menu dial on the video receiver until the linking status indicator blinks red and green alternately, indicating that it is ready to link. When the linking is complete, the linking status indicator turns solid green and the video receiver can communicate with the DJI Video Transmitter

Linking Status Indicator	Description
Solid red	Device started, not connected.
Blinks red and green alternately	Linking
Solid green	Successfully linked. Wireless video transmission is normal.
Blinks red	Device malfunction. Contact DJI Support.

Specifications

Model	RX3
Operating Frequency *	2.4000-2.4835 GHz, 5.150-5.250 GHz, 5.250-5.350 GHz,

5.470- 5.725 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)| 2.4 GHz: <33 dBm (FCC), <20 dBm (SRRC/CE/MIC) 5.8 GHz: <33 dBm (FCC), <14 dBm (CE), <23 dBm (SRRC)
Operating Temperature| -10 to 40℃

Due to the local regulations, the 5.1/5.2/5.8 GHz frequencies are prohibited in some countries and the 5.1/5.2 GHz frequencies are only allowed for use indoors in some countries. 5.600-5.650 GHz is not used.

FCC Compliance Notice

Supplier’s Declaration of Conformity

Product name: DJI Video Receiver

Model Number: RX3
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com

We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

ISED Compliance Notice

CAN ICES-003 (B) / NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the CNR-102.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

No operation is permitted for the frequency “5600-5650 MHz”
For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit.

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

This device is restricted to indoor use when operating in the 5150-5350MHz frequency range in all EU/EFTA member states, Türkiye and UK.

BE| BG| CZ| DK| DE| EE
IE| EL| ES| FR| HR| IT
CY| LV| LT| LU| HU| MT
NL| AT| PL| PT| RO| SI
SK| Fl| SE| UK(NI}| TR| NO
CH| IS| LI| | |

MIC Compliance Notice
W52/W53：In case of AP, “only indoor use”
Thailand Warning message