VAKOLE CO26 Electric Mountain Bike User Manual
- June 13, 2024
- VAKOLE
Table of Contents
VAKOLE CO26 Electric Mountain Bike
Product Information
CO26 Electric Mountain Bike User Manual
This user manual provides instructions on how to operate and install the CO26 Electric Mountain Bike. It also includes information on the product overview, main part description, display manual, installation instructions, and battery removal.
Product Instruction
Product Overview
- The CO26 Electric Mountain Bike is a versatile electric bike designed for off-road adventures. It features a powerful motor and a long-lasting battery, providing a smooth and efficient ride.
Main Part Description
- The main parts of the CO26 Electric Mountain Bike include the frame, motor, battery, display, handlebar, pedals, front fork, rear rack, and wheels.
Routine Operation
- To turn on/off the bike, long-press the switch button. The display will work normally, and the controller will power on at the same time.
- To enter the Walk Assist Mode, press and hold the Down button for 2 seconds. The e-bike will travel at a constant speed of 6km/h. Please note that the Walk Assist function is only for pushing the e-bike by hand and should not be used while riding.
- To switch the PAS (Pedal Assist System) level, short-press the UP or DOWN button. The default range of PAS levels is 0-5.
Display Manual
- Do not modify system parameters to avoid parameter disorder. If the e-bike is not used for more than 10 minutes, the display will automatically shut down.
Installation Instructions
- To install the CO26 Electric Mountain Bike, follow these steps:
- Put the wheel in the front fork and insert the front fork axle. Fix the screw.
- Install the handlebar and tighten the screws.
- Install the headlight and fender.
- Install the pedals.
- Install the rear rack.
- Ensure all screws are tightened properly.
Remove the Battery
To remove the battery from the e-bike, follow these steps:
-
1. Turn the key to unlock the battery. - Keep the key pointing to the unblock position and take out the battery from the e-bike.
When you are not riding the e-bike, please take out the battery and store it in a dry and ventilated place.
Error Code Definition (Appendix 1)
| Error Code | Definition | Solution |
|---|---|---|
| 05 | Brake failure | Check whether the brake is restored to the initial state |
| 06 | Undervoltage protection | Check battery voltage |
| 07 | Motor failure | Check whether the outgoing cable of the phase line is in |
good
condition; Check whether the motor phase cable is well-connected
with the controller
08| Throttle abnormal| Check whether the throttle is restored to the initial
state
09| Controller abnormal| Check whether the controller cable pins’ sequence
match
10| Communication abnormal| Check whether the display and controller are well
connected
11| Abnormal communication transmission| Check whether the display and
controller are well
connected
Product Instruction
Product overview
Main part description
Routine operation
On/Off
- Long press Switch button then the display will work normally, and the controller will power on at the same time.
Walk Assist Mode
- Press and hold Down button for 2 seconds to enter the Walk assist mode.
- The E-bike will travel at a constant speed of 6km/h.
- The Walk Assist function can only be used to push the e-bike by hand. Please don’t use this function when riding.
PAS Level Selection
- Short press the UP or DOWN button to switch the PAS level. The default range of the PAS level is 0-5 levels.
Display Manual
- Don’t modify system parameters to avoid parameters disorder.
- If the e-bike is not used for more than 10 minutes, the display will automatically shut down.
Installation Instructions
- Put the wheel in the front fork,insert the front fork axle, fix the screw
- Install the handlebar
- Tighten the screw
- Tighten the screw
- Install headlight
- Install the pedals
- Install the rear rack
- Done
Remove the battery
- Turn the key to unlock
- Keep the key pointing to the unbolck, take out the battery
- Remove the battery from the e-bike
When you are not riding the e-bike, please take out the battery and store it in a dry and ventilated place.
Appendix 1 Error Code Definition
| Error code | Definition | Solution |
|---|---|---|
| 05 | Brake failure | Check whether the brake is restored to the initial state |
| 06 | Undervoltage protection | Check battery voltage |
| 07 | Motor failure | Check whether the outgoing cable of the phase line is in |
good condition;
Check whether the motor phase cable is well **** connected to the controller
08| Throttle abnormal| Check whether the throttle is restored to the initial
state
09| Controller abnormal| Check whether the controller cable pins’ sequence
matches.
10| Communication abnormal| Check whether the display and controller are well-
connected
11| Abnormal communication transmission| Check whether the display and
controller are well-connected
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>