Tera 6900 1D Handheld Barcode Scanner User Manual

Tera 6900 1D Handheld Barcode Scanner

Preface

Thank you for buying this barcode scanner from Tera. Before using the barcode scanner; please read the instructions carefully and do not arbitrarily scan the setting codes. Otherwise, some functions may be turned on or off unintentionally.

How to use this scanner

1. Connect the computer USB interface, the buzzer prompts, and the indicator light at the top of the scanner is always on, so if they both trigger; it means the connection was successful.
2. Open any document and enable the editing state. You must first confirm that the cursor is displayed. After doing so, press the button to start scanning the code without installing a driver.
3. There will be a buzzer sound when the code is scanned successfully, and the corresponding content of the code will be displayed in the document.
4. For more functions, please refer to the setting codes in the manual.
5. If you have any questions or concerns about the operation of the scanner, please contact us at the following email address: service@tera-digital.com
   ( Please indicate the scanner model number or the order number; describe the problem you encountered and/or attach a video of the malfunction.)

• Restore Factory Default
  If the scanner fails to operate due to improper configurations or other reasons, scan this barcode to restore it to factory settings.

• Scanning Mode Setting
  Trigger Mode: Hold the trigger button to scan, then release the trigger to end the scan. The red scan light will only show up when you press the button.

• Delay Mode: After reading a barcode, if the key has not been released, you can continue scanning.

• Single-Click Mode: The difference between single-click mode and normal manual mode is that you only need to click the button to read the barcode, instead of pressing the button continuously.

• Continuous Scanning Mode: Scan barcodes automatically without pulling the trigger button, as the scanner works continuously.

• Automatic Scanning Mode with Smart Stand: When the scanner is placed on the bracket, the scanner will automatically turn on the automatic sensing function within a few seconds. After leaving the bracket, the scanner will automatically return to the trigger mode within a few seconds.

• Volume Setting

• Tune Setting

• USB Device Type
  The default is “HID Emulation Keyboard”. Since most devices have integrated USB HID device drivers, there is no need to install additional software to use this scanner.
  Note: If you want to use the USB interface to emulate the serial port, you need to install the Virtual COM Driver provided by the manufacturer

• USB Keyboard Language

• Uppercase and Lowercase

Symbology Enable and Disable

Prefix and Suffix Setting

Add Prefix

The prefix setting includes two components: one is whether to enable the prefix character, and the other is the content of the prefix character. The prefix of the barcode can be any ASCII character ranging from 0 to 8 digits. Please set and enable the prefix as follows:

1. Start setting prefix.
2. According to the content to be added, refer to the “ASCII Code Character Table” and scan the corresponding setting codes to the custom the preffix. Each character corresponds to 2 hexadecimal numbers, for example, “AB” corresponds to “41 42”.
3. Scan the “End Parameter Input” setting. If you hear “Du-Di”, the setup has successed.
4. Scan the “Enable Prefix” setting barcode to complete adding prefix.

Clear Added Prefix

Add Suffix

Please set and enable the suffix as follows:

1. Scan the barcode “Start setting suffix”.
2. According to the content to be added, refer to the “ASCII Code Character Table” and scan the corresponding setting codes to the custom the suffix. Each character corresponds to 2 hexadecimal numbers, for example, “AB” corresponds to “41 42”.
3. Scan the “End Parameter Input” setting. If you hear “Du-Di”, the setup has successed.
4. Scan the “Enable Suffix” setting barcode to complete adding suffix.

Clear Added Suffix

Insert String Setting

Users can insert one or two strings: G1 and G2, with a range of 0-16 characters in the appropriate position of the barcode data according to their needs (the length of 0 means an empty string). G1 and G2 can be inserted into any position of barcode characters of a specific barcode type, or into any position of barcode characters of all barcode types. G1 and G2 must be set separately (when G2 is set to a null character, it means that only one string G1 has been inserted).

Please set and and insert strings as follows:

1. Scan “Start setting G1 character”.
2. According to the content that needs to be added, refer to Appendix 1, scan the corresponding setting codes to the custom the string. Each character corresponds to 2 hexadecimal numbers, for example, “AB” corresponds to “41 42”.
3. Scan the “End Parameter Input” setting barcode. If you hear “Du-Di”, the setup has successed.
4. Scan the setting barcode “Start setting G1 position”.
5. Scan the parameter barcodes and enter the two-digit position parameters in sequence. For example, in order to insert G1 after the first character of the barcode, then scan the parameter barcodes 0 and 1.
6. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.
7. Scan the barcode ” Insert String 1″.
8. Scan the number of the string to be inserted. (1 and 2 correspond to G1 and G2 respectively; 0 means no insertion.)
9. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.
10. Scan the setting barcode “Start setting G2”.
11. According to the content to be added, refer to ” Appendix 1″ and corresponding setting codes to the custom the string. (“0 0” means G2 is an empty string.)
12. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.
13. Scan the setting barcode “Insert String 2”.
14. Scan the number of the string to be inserted. (1 and 2 correspond to G1 and G2 respectively; 0 means no insertion.)
15. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.

Hide Prefix and Suffix Hide Prefix

Users can hide prefix as follows:

1. Scan the barcode “Hide Prefix”
2. Scan the following barcode “F” for several times to determin the number of the hidden characters. (Each character corresponds to two “F”, for example, scanning “F” for 4 times means 2 characters will be hidden.)
3. Scan the “End Parameter Input “setting barcode.
4. Scan the following two setting barcodes to insert string.
5. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.

Hide Suffix

Users can hide suffix as follows:

1. Scan the barcode “Hide Suffix”
2. Scan the following barcode “F” for several times to determin the number of the hidden characters.(Each character corresponds to two “F”, for example, scanning “F” for 4 times means 2 characters will be hidden.)
3. Scan the “End Parameter Input “setting barcode.
4. Scan the following two setting barcodes to insert string.
5. Scan the “End Parameter Input “setting barcode. If you hear “Du-Di”, the setup has successed.

Terminator Setting

Appendix 1

ASCII Chart

Special Function Keys

H

L

| Keyboard cable /USB| RS-232
---|---|---
0| 1| 0| 1
0| Null|  | NUL| DLE
1| Up| F1| SOH| DC1
2| Down| F2| STX| DC2
3| Left| F3| ETX| DC3
4| Right| F4| EOT| DC4
5| PgUp| F5| ENQ| NAK
6| PgDn| F6| ACK| SYN
7|  | F7| BEL| ETB
8| Bs| F8| BS| CAN
9| Tab| F9| HT| EM
A|  | F10| LF| SUB
B| Home| Esc| VT| ESC
C| End| F11| FF| FS
D| Enter| F12| CR| GS
E| Insert| Ctrl+| SO| RS
F| Delete| Alt+| SI| US
H

L

| 2| 3| 4| 5| 6| 7
---|---|---|---|---|---|---
0| SP| 0| @| P| `| p
1| !| 1| A| Q| a| q
2| “| 2| B| R| b| r
3| #| 3| C| S| c| s
4| $| 4| D| T| d| t
5| %| 5| E| U| e| u
6| &| 6| F| V| f| v
7| ‘| 7| G| W| g| w
8| (| 8| H| X| h| x
9| )| 9| I| Y| i| y
A| *| :| J| Z| j| z
B| +| ;| K| [| k| {
C| ,| <| L| | l| |
D| –| =| M| ]| m| }
E| .| >| N| ^| n| ~
F| /| ?| O| _| o| DEL

Normal characters

• Example: ASCII “!” = “21”

Appendix 2

Parameter Barcode

Appendix 3

Common Q & A

The scanner does not light up.

• The scanner is not powered. Check the power supply of the device.
• If an incorrect cable is used, please use the cable provided by the original manufacturer.
• The cable interface might be loose. Try reconnecting it.

The scan is normal, but the data output is incorrect.

• If the interface is loose, reconnect it.
• The keyboard input mode of the device is not set correctly, please correct the setting to allow the input of English letters.
• If you are using a PS2 cable and garbled characters appear during data output, it may be that the data receiving speed of the device does not match the scanner.

The scanner cannot decode some barcodes.

• The barcode can be defective, try to scan the same type of the test barcode to determine whether it can be interpreted.
• The scanner might not be at an adequate distance from the barcode, please move the scanner closer or farther away from the barcode.
• For barcodes with poor printing quality, the optimal reading distance is 5-10 cm.

Other situations of unseccessful reading barcodes.

• Try restarting the device. Turn off the power of the device; connect thedevice and the scanner correctly; turn on the deviceand scan again.
• If the problem still cannot be solved, please contact the manufacturer.

If you need any product support, please contact our customer service.

Important Notice: Please attach your Amazon Order Number and Product Model Number in the email.

Official Customer Service Email Addresses:

1. service-us@tera-digital.com
2. service-eu@tera-digital.com
3. service-uk@tera-digital.com

Cell/WhatsApp: +8613382526580

Contact us on social media:

• Instagram: teradigital.official
• Youtube: Tera-digital
• Twitter: Tera-digital
• Facebook: Tera Scanner

If you want to learn more about our brand or need a digital user manual of the latest version, please visit our official website via the links below or by scanning the given QR code:

• Website: https://tera-digital.com/
• User Manual: https://tera-digital.com/pages/user-manual

FREQUENTLY ASKED QUESTIONS

What is the Tera 6900 1D Handheld Barcode Scanner?

The Tera 6900 1D Handheld Barcode Scanner is a portable device designed to read and decode one-dimensional (1D) barcodes, such as UPC codes, for various applications, including inventory management and point-of-sale (POS) systems.

How does the Tera 6900 Barcode Scanner work?

The Tera 6900 scanner uses a laser or LED light source to scan and capture data from 1D barcodes. It then processes the information and sends it to a connected device, such as a computer or POS system.

Is the Tera 6900 scanner compatible with all types of 1D barcodes?

The Tera 6900 scanner is designed to be compatible with a wide range of 1D barcode symbologies, including UPC-A, EAN-13, Code 128, and more.

Can I use the Tera 6900 scanner for retail and point-of-sale (POS) applications?

Yes, the Tera 6900 scanner is suitable for retail and POS applications, making it a valuable tool for scanning product barcodes, managing inventory, and processing transactions.

Is the Tera 6900 scanner suitable for inventory management?

The Tera 6900 scanner is well-suited for inventory management tasks, allowing you to efficiently track and update inventory levels using barcode data.

Can the Tera 6900 scanner connect to a computer or mobile device?

Yes, the Tera 6900 scanner typically connects to a computer or mobile device via USB, Bluetooth, or other wired/wireless connectivity options, depending on the model.

Does the Tera 6900 scanner come with software for data management?

Some Tera 6900 scanner models may come with software for data management, while others may be compatible with third-party software applications for data processing and analysis.

Is the Tera 6900 scanner suitable for industrial use?

The Tera 6900 scanner can be used for industrial applications, particularly in manufacturing, logistics, and warehouses where barcode scanning is crucial for operations.

What is the warranty for the Tera 6900 1D Handheld Barcode Scanner?

The warrantie typically range from 1 year to 2 years.

Can the Tera 6900 scanner read damaged or poorly printed barcodes?

The Tera 6900 scanner is designed to read standard barcodes effectively. However, its ability to read damaged or poorly printed barcodes may depend on the specific model and scanning technology.

What is the scanning range of the Tera 6900 scanner?

The scanning range of the Tera 6900 scanner can vary by model but is typically optimized for reading barcodes at various distances, from close range to a few feet away.

Is the Tera 6900 scanner compatible with Mac and Windows operating systems?

The Tera 6900 scanner is often compatible with both Mac and Windows operating systems, making it versatile for use with a wide range of devices.

Does the Tera 6900 scanner have a trigger or button for manual scanning?

Many Tera 6900 scanner models feature a trigger or button that allows for manual scanning when needed, offering flexibility in the scanning process.

Can I use the Tera 6900 scanner for document scanning?

The primary purpose of the Tera 6900 scanner is to read 1D barcodes, but it may not be suitable for document scanning or text recognition.

Is the Tera 6900 scanner suitable for asset tracking?

Yes, the Tera 6900 scanner is a valuable tool for asset tracking applications, enabling organizations to efficiently monitor and manage their assets using barcode data.

What is the weight and dimensions of the Tera 6900 scanner?

The 1.23 pounds weight and 8.3 x 5.9 x 3.9 inches dimensions of the Tera 6900 scanner.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK:Tera 6900 1D Handheld Barcode Scanner User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>