dji Spark Battery Charging Hub User Guide
- June 13, 2024
- DJi
Table of Contents
SPARK
Battery Charging Hub
Spark Battery Charging Hub
Disclaimer
Thank you for purchasing SPARK™ Intelligent Flight Battery Charging Hub
(hereinafter referred to as ‘Product’). Read this disclaimer carefully before
using this Product. By using this Product, you hereby agree to this disclaimer
and signify that you have read it fully. Please use this Product in strict
accordance with the manual and be sure to pay attention to the Warning. SZ DJI
TECHNOLOGY CO., LTD. and its affiliated companies assume no liability for
damage(s) or injuries incurred directly or indirectly from improper use of
this Product. Misuse includes, but is not limited to, using unapproved
chargers, charging unapproved batteries, short-circuiting, overheating,
modifying the Product, or touching the terminals with skin or metal. Refer to
the Disclaimer and Safety Guidelines, Intelligent Flight Battery Safety
Guidelines, and User Manual for applicable information not herein contained.
DJI™ is a trademark of SZ DJI TECHNOLOGY CO., LTD. (abbreviated as “DJI”) and
its affiliated companies. Names of products, brands, etc., appearing in this
manual are trademarks or registered trademarks of their respective owner
companies. This Product and manual are copyrighted by DJI with all rights
reserved. No part of this Product or manual shall be reproduced in any form
without the prior written consent or authorization of DJI.
This disclaimer is produced in various languages. In the event of divergence
among different versions, the Chinese version shall prevail when the Product
in question is purchased in China, and English version shall prevail when the
Product in question is purchased in any other region.
Warning
- The Charging Hub is only compatible with the battery chargers specified in “Specifications”.
- The Charging Hub is only compatible with MB1-1480mAh-11.4V Intelligent Flight Batteries. DO NOT attempt to use the Charging Hub with other battery models.
- Ensure the battery temperature is within the appropriate temperature range when in use.
- The Charging Hub will intelligently limit the charging current if the battery temperature is low to prevent a hazard, which may prolong the charging time.
- Place the Charging Hub on a flat and stable surface when in use. Ensure the device is properly insulated to prevent fire hazards.
- DO NOT touch the metal terminals on the Charging Hub.
- If there is any noticeable buildup, wipe the metal terminals with a clean, dry cloth.
Introduction
The Spark Intelligent Flight Battery Charging Hub is designed for charging the
Spark Intelligent Flight Battery. When used with the specified Spark Battery
Charger, it can charge up to three Intelligent Flight Batteries in sequence,
or even simultaneously, based on their power levels and cell voltage for
efficient, optimized charging. When the battery temperature is low, the
Charging Hub will limit the charging current to prevent a hazard and to
prolong the battery service life.
Overview
- Firmware Update Port (Micro USB)
- Battery Slot Track
- Charging Port
- Status LED
- Power Port
Using the Charging Hub
Follow the instructions below to use the Charging Hub. Example: Spark Battery
Charger (F1C50 Version 2).
-
Connecting to a Power Source
Connect the Spark Battery Charger to a power outlet (100-240V 50-60Hz), then connect the Charging Hub to the Spark Battery Charger. -
Connecting the Batteries
Align the battery with the Battery Slot Track and put the battery in as shown below. Then push the battery in to make it properly inserted. The Charging Hub will intelligently charge batteries in sequence, or even simultaneously, based on their power levels and cell voltage for efficient, optimized charging. It is normal that there are one or more batteries being charged at the same time due to differences in power levels, battery cell voltage, and battery temperature. Please check the Status LED to monitor charging.
Refer to “Status LED Indicator Descriptions” for more information about the Status LED indicator’s blinking patterns. The Battery Level Indicators will turn off when charging is complete. Detach the batteries from the Charging Hub.
- Please make sure the batteries are correctly inserted before charging.
- DO NOT cover the Charging Hub when in use.
Status LED Indicator Descriptions
Status Light | Description |
---|---|
-Pulsing Green | Charging. |
— Solid Green | Fully Charged. |
— Solid Red | Power supply or battery error. Check components. |
— Solid Yellow | Charging Hub connected correctly. Please insert batteries. |
Updating Firmware
The Charging Hub can be updated using the firmware update program. If no
firmware update program is released on the Downloads page of the official DJI
website, it indicates that the product firmware is up-to-date and no update is
required.
Specifications
Model | S1CH |
---|---|
Compatible Battery Charger | Spark Battery Charger (F1C50 Version 2) |
Compatible Battery Model | MB1-1480 mAh-11.4 V |
Operating Temperature Range | 32° to 104° F (0° to 40° C) |
Input Voltage | 13.05 V |
Input Current | 3.83 A |
Weight | 67.2 g |
Charge Time* (Three Batteries) | Spark Battery Charger (F1C50 Version 2): |
Approx. 90 minutes
- Charging time was tested in a lab environment at room temperature (25° C).
To be taken as reference only.
This content is subject to change.
Download the latest version from
http://www.dji.com/spark
SPARK and DJI are trademarks of DJI.
Copyright © 2017 DJI All Rights Reserved.
If you have any questions about this document,
please contact DJI by sending a message to
DocSupport@dji.com.
Printed in China.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>