COMMSCOPE SSH-47 Snap Tak Adjustable Cable Hanger Instruction Manual
- June 13, 2024
- CommScope
Table of Contents
COMMSCOPE SSH-47 Snap Tak Adjustable Cable Hanger
Product Information
The SnapTak hanger is a cable support system offered by CommScope Infrastructure Academy. It is designed with a circular support channel and multiple support members to securely hold cables in place.
The hanger comes in different sizes, each suitable for specific cable diameter ranges:
- Part Number: SSH-47
- Cable Diameter Range: 4.00mm min to 7.00mm max
- Part Number: SSH-710
- Cable Diameter Range: 7.10mm min to 10.00mm max
- Part Number: SSH-1014
- Cable Diameter Range: 10.10mm min to 14.00mm max
- Part Number: SSH-1416
- Cable Diameter Range: 14.10mm min to 16.00mm max
The SnapTak hangers are made of polymer material, but they can be snapped into any other CommScope metal or polymer SnapTak hanger size.
For additional resources and information on hanger selection and spacing, you can visit the following links:
Product Usage Instructions
- Place the SnapTak hanger under the cable you want to support.
- Ensure that the cable is centered in the keyhole channel of the hanger.
- Push the cable into the support channel of the hanger.
- While doing so, use your finger or thumb to expand the hanger latches.
- hanger.
- If using polymer SnapTak hangers, they can be snapped into any other CommScope metal or polymer SnapTak hanger size.
FOnce the cable is securely in place, snap it into the or any further assistance or customer support, you can reach out to CommScope Infrastructure Academy:
- Phone (North America): +1-800-255-1479 (toll-free)
- Phone (Any country): +1-779-435-6500
- Email: acicustomersupportcenter@commscope.com.
Installation Instructions
SSH-47
- CommScope® SnapTak Adjustable Cable Hanger
- Bulletin 7761654 Rev. D
CommScope Infrastructure Academy offers installation training.
- The SnapTak hanger has a circular support channel and multiple support members to engage the cable.
- Place hanger under cable.
- Push cable into the support channel while expanding hanger latches with finger or thumb.
- Cable should be centered in keyhole channel and snapped in place.
- Push SnapTak hanger in tower member or mounting adapter with ¾” hole. Snap the latches in places.
- Polymer SnapTak hangers may be snapped into any other CommScope metal or polymer SnapTak hanger size.
Note
- Visit commscope.com click QR codes above for hanger selection and hanger spacing resources. Hanger selection calculator: https://www.commscope.com/SnapStak/.
- Hanger specification and hanger spacing guide: https://www.commscope.com/Product-Catalog/Tools-and-Accessories/Product/Coaxial-Tools,Consumables-and-Accessories/.
Part Information for Available Hangers
Part Number| Stackability| Cable Diameter Range (mm)
SSH-47| 3| 4.00 min to 7.00 max
SSH-710| 3| 7.10 min to 10.00 max
SSH-1014| 3| 10.10 min to 14.00 max
SSH-1416| 3| 14.10 min to 16.00 max
Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.
CONTACT
CommScope
- 1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339
- 828-324-2200 800-982-1708
- www.commscope.com.
Customer Service 24 hours
- North America: +1-800-255-1479 (toll free)
- Any country: +1-779-435-6500
- email: acicustomersupportcenter@commscope.com.