CBS FLX Flo X Monitor Arm User Guide

June 13, 2024
CBS

CBS FLX Flo X Monitor Arm

FLOXMONITOR ARM FLX/018/010

COMPONENT LIST

  • FLO X Arm

  • VESA Plate x 1

  • M4x12mm VES A Screws x 4
    M4x10mm V ESA Screws x4
    Optional Security Screw x1

  • 2.5mm Allen Key x 1
    3mm Allen Key x 1
    5mm Allen Key x1

OTHER KITS REQUIRED

  • Flo X Split Clamp FLX/018/AS01

    OR

  • Flo X Top Mount Clamp FLX/ 018/C07

Prefer red Clamping Method

www.colebrookbossonsaunders.com

FIT DESK FIXING TO WORKSURFACE

Follow instructions provided with chosen desk finxing

FLO X SPLIT CLAMP
FLX/018/AS01

FLO X TOP MOUNT CLAMP
FLX/0 18/C07

FIT MONITOR ARM TO CLAMP

Fit Monitor Arm To Clamp

NOTE
Ensure that plastic bush is in place

IMPORTANT
Ensure that arm is pushed fully down onto clamp

ATTACH VESA PLATE TO MONITOR

Use screws supplied
Be sure to select correct length

Attach Vesa Pl Ate To Monitor

Screws over-inserted
Attach Vesa Pl Ate To Monitor

Screws under-inserted
Attach Vesa Pl Ate To Monitor

IMPORTANT

It is the responsibility of the installer to ensure all mounting screws are properly engaged with a minimum of 4 x 360° turns into the display.
Under or over insertion may cause damage to the equipment or injury to personnel.

OPTIONAL STEP

DUAL SPRING CONFIGURATION

If the monitor to be mounted weighs less than 9kg (2016), you may need to configure the Flo X Dual Spring mechanism to suit the lower weight range.

Factory set dual spring configuration is suitable. Go to step 5

Dual spring mechanism will need to be reconfigured to lower weight range. See step 12

MOUNT MONITOR TO ARM

NOTE
See Optional Step 10 for Security Screw installation

ADJUST ARM TO SUIT WEIGHT OF MONITOR

Turn adjuster screw until monitor ‘floats’ in all height posit ions

The arm setting indicator allows for 9uick installation of multiple arms

You can quickly ‘dial’ into the same setting, then if necessary, fine tune the adjustment to balance the monitor

OPTIONAL STEP

VESA FRICTION ADJUSTMENT (if required)

IMPORTANT
Portrait-to – landscape monitor rotation is factory- set for optimum performance, however if the monitor droops sideways, rotation friction can be adjusted as described below.

Adjust the friction just enough to avoid unwanted rotation

Vesa Friction Adjustment \(If Required\)

OPTIONAL STEP

TILT HEAD FRICTION ADJUISTMENT (if required)

IMPORTANT
Monitor tilt should balance with factory settings. If monitor droops, adjust friction using adjuster screw beneath tilt joint.

Note the position of the silver disc, indicating how much friction is applied to the monitor tilt.

Tilt Head Friction Adjuistment \(If Required\)

Adjust the tilt friction just enough to avoid unwanted monitor droop.

For heavy monitors turn the alien key to the left (in direction of the arrow).

For lighter monitors turn the alien key to the right ( in direction of the arrow).

Note that drawing shows the top of the tilt head as viewed over the top of the monitor from the front of the desk.

INSTALL CABLES

IMPORTANT
Ensure that you allow enough free cable for easy monitor movement in all directions

OPTIONAL STEP

SECURITY SCREW

Security screw locks monitor to arm

Security Screw

TO REMOVE MONITOR

To Remove Monitor

IMPORTANT
Raise arm to uppermost position before removing monitor otherwise it may spring up when unloaded.

To Remove Monitor

OPTIONAL STEP

DUAL SPRING CONFIGURATION

If the monitor to be mounted weighs less than 9kg (2016) you may need to reconfigure the dual spring mechanism to the lower weight range.

An extra long T-Bar Allen Key is required to perform this adjustment – see guidance drawing below. This tool is not supplied with Flo X.
If you do not have a suitable tool, we can supply one.
Please contact your account manager or dealer to request a tool.

Hold the arm in its lowest position to help with mechanism adjustment.
(You may find this easier by installing the monitor first.)

Dual Spring Configuration

Be sure to insert the Allen Key in the hex detail of the lower hole.

Use the 5mm Allen Key to adjust the mechanism. This will disengage one of the Flo X dual springs and will reduce the weight support range.

IMPORTANT
Turn the screw anti-clockwise to the , end of its travel and fully tighten to disengage one of the Flo X dual springs.

The spring is fully disengaged when the plastic wedge on the underside of the arm (shown in grey left) is drawn fu lly forwards and level with the arm body.

TO RETURN TO FACTORY SET DUAL SPRING:
If Flo X Dual Spring mechanism has already been configured to low weight range, it can be returned to high load range by repeating the above process , except turning the adjuster screw clockwise until the mechanism reaches the end of its travel.

FLX- 018 – 0 10 – IN ST-A -SEPT 2022

Please consider leaving these instructions with the product if further installation may be required by others

WARNING

  • Ensure desk/work surface/wall/partition is suitable to take the weight of the arm/sand monitors.
  • Do not use this product for any purpose other than that for which it was designed.
  • Supported weight must not exceed 18kg (4016) per arm.
  • Hold the monitor tightly when making adjustments.
  • Care should be taken to avoid trapping fingers.
  • Do not dismantle or remodel the arms.
  • Do not attach the monitor before assembling arm .
  • Some monitors have recesses and may require spacers or a 75mm VESA plate.
  • The screws supplied for the installation of the arm are supplied in good faith and with the intention that they will be used with the correct monitor, namely a monitor with VESA mounting holes. Please therefore check before attempting installation that you have the appropriate equipment on which to carry out the installation. CBS cannot be held liable for any damage caused to your equipment resulting from a failure to make this check. Please also carefully read the installation instructions to ensure correct fixing.

MAINTENANCE AND INSPECTION

  • Ensure all screws are tightened and occasionally adjust if needed.
  • Clean with a damp cloth, NO solvent.

DISCLAIMER

As part of Colebrook Bosson Saunders ongoing product improvement programme, the design of products may change without prior notice and details may vary from those illustrated.

FLO X SPLIT CLAMP FLX/018/AS01

PARTS INCLUDED

Parts Included

CONFIGURE CLAMP BRAC KET

If required change the clamp plate setting by removing the screws and adjusting to correct setting

Desk Thickness Range

INSTALL CLAMP SCREW AND CLAMP PAD

FIT CLAMP TO DESK

TIGHTEN CLAMP SCREW

Use Allen Key provided with clamp

IMPORTANT NOTE

Ensure screw is tightened

CONFIGURE 180° STOP (if required)

FIT CLAMP COVER AND BUSH

ALTERNATIVE INSTALLATION METHODS FOR RESTRICTED GAP AT REAR OF WORK

SURFACE

  • Do not use this product for any purpose other than that for which it was designed
  • Ensure desk/worksurface is suitable to take the weight of the arm/sand monitors
  • Supported weight must not exceed the maximum load per arm
  • Take care when installing as fingers could become trapped
  • Ensure all screws are tightened and occasionally adjust if needed
  • Ensure arm is pushed fully down onto the clamp before installing the monitor(s)
  • Clean with a damp cloth, NO solvents
  • The use of power tools, lever bars or excessive force during the installation, or re-configuration of the product will invalidate your guarantee
  • Failure to observe the recommendations in the use, and configuration of these products may affect your guarantee
  • As a part of Colebrook Bosson Saunders ongoing product improvement programme the design of products may change without prior notice and details may vary from those illustrated

PATENTS
Colebrook Bosson Saunders hold a number of patents and other intellectual property rights covering our products and processes.
You can find patent information on our website at:
www.colebrookbossonsaunders.com/patents

CBS Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals