Tonly Technology WFAVD30-W-BX-L WiFi Smart Voice Dimmer Instruction Manual
- June 6, 2024
- Tonly Technology
Table of Contents
Technology WFAVD30-W-BX-L WiFi Smart Voice Dimmer
Instruction Manual
Your installation is finished!
Enjoy your new Wi-Fi smart voice dimmer.
For videos and other information on how to use your Wi-Fi smart voice dimmer visit: Eaton.com/SmartHome
www.eaton.com
www.Eaton.com/SmartHome
For troubleshooting contact us at:
TechSupport@eaton.com or
1-866-853-4293, option 2
Issues setting up or using your device?
Q: Device not working, the load does not come on, LED indicator bar not
functioning
A: – Check to make sure your breaker is turned on
– Make sure the air gap switch is pushed in
– Make sure wiring is correct by following the provided wiring instructions
closely
Q: Lights are flickering
A:-Mae sure wiring is correct by following the provided wiring instructions
closely
– Make sure wiring is not loose
– Adjust the minimum brightness level to a higher level
Q: Alexa is not working
A:-Make sure your device is registered in the Amazon Alexa app using the
instructions provided
– Check that your internet connection is working
– Pull the air-gap switch and push it back in to reboot the device
Q: Device unable to connect to Wi-Fi
A:-cheek that the router is powered on
– Check that you have the correct network name and password
– Make sure your Wi-Fi router is in a location that is suitable for good
signal quality
Still, having issues? Visit Eaton.com/SmartHome
or contact us at
1-866-853-4293, option 2 for more help.
Visit www.eaton.com/smarthome to adjust the
minimum brightness level
Eaton Wi-Fi smart voice dimmer
Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc or its affiliates.
WARNINGS AND CAUTIONS
- Turn OFF circuit breaker or remove the fuse(s) and test that the power is OFF before starting the installation process
- Never wire any electrical device with the power turned ON
- If you are not sure about any part of these instructions, please contact a licensed electrician
- If bare copper or green ground connection is not available in the wall box. contact a licensed electrician for installation
- Use only #14 or #12 copper wire rated for at least 75 degrees C with these devices. DO NOT USE
ALUMINUM WIRE CAUTION
- Use only with 120V/AC 60Hz
- Do not exceed the rnaxirnum rating of the dimmer as indicated on the device
- Must be installed and used in accordance with all national and local electrical codes
- Suitable for installation in outlet box measuring a minimum 3″ x 2″ x2-1/2″ deep and wired in accordance with NEC article 314 box fill requirements
IMPORTANT
- The dimmer will not work or will be damaged if wired incorrectly and the warranty will be voided. Refer to the wiring instructions provided
- Wiring dimmer HOT may cause permanent damage to dimmer and void warranty
OPERATION INSTRUCTIONS
- Press the ON/OFF button to turn the lights ON
- Press the button again to turn the lights OFF
- Pull the air-gap switch to disconnect power to the load
QUICK MAX
- When the lights are OFF. press and hold the ON/OFF button for 2 seconds. The device will then instantly turn ON at its maximum brightness level
DELAYED OFF
When the lights are ON, press and hold the ON/OFF button for two seconds. The
device will then wait 10 seconds before turning the lights OFF. During this
time. the LED indicator bar will blink white until the lights turn OFF. At
this point. you can press the ON/OFF button again to override the timer and
turn OFF the lights immediately.
FACTORY RESET
The dimmer can be reset which will exclude it from its network and restore all
factory defaults.
Press and hold the Privacy button for 30 seconds. Upon successful completion.
the LED indicator bar will slowly fade in and out an orange color to indicate
that the device is now unregistered and ready to be set up again.
DIMMER RATING
| Load Type| Single Gang| 2-Gang| 3-Gang
---|---|---|---|---
WFAVD30| CFL/LED/FLR/ MLV/INC/HAL/ELV| 300W| 300W| 200W
For more advanced configuration parameters such as adjusting the LED indicator bar brightness and other features. please visit: MLV/INC/ HAL/ELV Eaton.com/SmartHome
WIRING DIAGRAMS
Single location control installation Two location control installation using a standard 3-way switch
Multi-location control installation using a standard 3-way switch
For videos and other information on how to use your Wi-Fi smart voice
dimmer visit: Eaton.com/SmartHome
Get your Wi-Fi smart voice dimmer running in 3 easy steps!
Step1 Install your Wi-Fi smart voice dimmer per the instructions provided
in this booklet
Step2 Download the Amazon Alexa app via the App Store
Step3 Add your device to the Amazon Alexa app in a few easy steps:
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
BEFORE INSTALLATION FCC CAUTION: Any changes or modifications not
expressly approved by Eaton Wiring Devices could void the user’s authority to
operate the equipment.
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
This equipment complies with ISED RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20cm between the radiator and any part of
your body.
EATON WIRING DEVICES LIMITED 2 YEAR WARRANTY
Eaton Wiring Devices warrants its Wi-Fi smart device to be free of defects in
materials and workmanship in normal use and service for a period of two years
from date of original purchase. THIS TWO (2) YEAR LIMITED WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, OBLIGATIONS, Eaton Wiring Devices warrants this smart
device to be free of defects in materials and workmanship in normal use and
service for a period of two years from the date of original purchase. THIS TWO
(2) YEAR LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, OBLIGATIONS, OR
LIABILITIES, EXPRESSED OR IMPLIED (INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS IN DURATION IN
EXCESS OF TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER PURCHASE). NO AGENT,
REPRESENTATIVE, OR EMPLOYEE OF EATON HAS THE AUTHORITY TO INCREASE OR ALTER
THE OBLIGATIONS OF EATON UNDER THIS WARRANTY. To obtain warranty service for
any properly installed Eaton smart device that proves defective in normal use
send the defective smart device prepaid and insured to Quality Control Dept.,
Eaton Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269, in Canada:
Eaton Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario LSR 1B8.
Eaton will repair or replace the defective unit at its option. Eaton will not
be responsible under this warranty if the examination shows that the defective
condition of the unit was caused by misuse, abuse, improper installation,
alteration, improper maintenance or repair of damage in shipment to Eaton.
EATON SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OF THE SMART DEVICE, OR
FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR ANY SPECIAL, INCIDENTAL,
CONTINGENT, OR CONSEQUENTIAL DAMAGES OF ANY KIND, RESULTING FROM DEFECTS IN
THE DIMMER OR FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PROTECT.
THE EXCLUSIVE REMEDY FOR BREACH OF THE LIMITEO WARRANTY CONTAINED HEREIN IS
THE REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT AT EATON’S OPTION. IMPLIED
WARRANTIES!IF ANY) INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF FITNESS
FDR A PARTICULAR PURPOSE ANO MERCHANTABILITY, ARE LIMITED IN DURATION TO A
PERICO ENDING TWO YEARS FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. IN NO
CASE SHALL EATON’S LIABILITY UNDER ANY OTHER REMEDY PRESCRIBED BY LAW EXCEED
THE PURCHASE PRICE.
Some states do not allow the exclusion or limitation of incidental or
consequential damages or allow disclaimers or modifications of or limitations
on how long an implied warranty lasts, so the above limitations may not apply
to you. Some Canadian provinces do not allow exclusion or variance of implied
warranties so some or all of the above limitations may not apply to you. This
warranty gives you specific legal rights and you may also have other rights
which vary from state to state and province to province. Read enclosed
instructions care fully. If you have any questions concerning the use or care
of this product please write.
Consumer Service Division,
Eaton Wiring Devices,
203 Cooper Circle,
Peachtree City,
GA 30269.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>