ZETHORS XN-P010 Smart Air Pump User Manual

User Manual Smart Air Pump
Model: XN-PO10

Thank you for buying ZETHORS Smart Air Pump. For the best user experience, please read this user manual carefully before use and keep it for further reference.

Please note before use!

1. This product should be placed and used away from chil- dren.
2. Please read carefully and fully understand the operation instructions before use.
3. Please check before using the air pump, if there is any abnormality, do not use it.

Warnings! Make sure you’ve selected the correct tire pressure and operate it properly!

1. Correct tire pressure is very important for safe driving.
2. This product s not suitable for tires that require high capacity/high air pressure!
3. Before setting the inflation pressure value, please make sure the correct unit of measurement is selected, or it may cause accidents like tire burst.
4. Make sure to inflate the tires and check the spare tire regularly according to the air pressure recommended by the car manufacturer.

Warnings! Danger due to improper use!

1. Please use itin a safe area, and do not use it in a flamma- bie and explosive environment.
2. Please use itin a dry and clean environment. The intru- sion of sand and dust may cause damage to the product.
3. Do not fold and squeeze the air tube when inflating, please keep the air flow smooth.
4. The operator cannot leave the site when the air pump is working. Itis necessary to observe the inflation process 1o prevent the inflation pressure from being too high when the preset pressure is not set.
5. Under-inflation or over-inflation may be dangerous (do not over-inflate).
6. The temperature of air tube willrise when the product works for a long time. If the product makes abnormal noise or the temperature is too high, please shut down immediately and use it after the product cools down for 10 minutes.
7. It is recommended not to use it continuously for more: than 10 minutes. When exceeds 10 minutes, please shut it down and cool it down for 5 minutes before continuing to useit.
8. When using a charger for power supply, please buy or use a 5V-1A/2A charger that obtains safety certification (CCC, CE, FCC, PSE, UL, etc) and meets the standard requirements.
9. The product is not waterproof, and it is forbidden to rinse with water.

Battery Warnings!

1. It is forbidden to disassemble, impact, squeeze or put into fire; if severe swelling occurs, stop using. Do not place it in high temperature environment.
2. There will be risk of explosionf battery is incorrectly replaced, please replace only with the same or equivalent type.
3. Batteries (battery packs or assembled battery) must not be exposed to excessive heat such as sunlight, fire, or similar overheated environment.
4. Do ot use damaged or modified battery packs, as un- predictable consequences may ocour, resulting in risks of fire, explosion and injury.
5. The storage temperature of the product should not be lower than -10°C or higher than 45°C. Overcooling or overheating will shorten the product life and damage the built-in battery.
6. In order to ensure the battery life, it is recommended to use or charge it at least once every 3 months.
7. For products containing lithium batteries, please dispose of them separately from household waste. To reduce pollution and maximize the protection of the earth’s envi- ronment, the product should be disposed of at the end of its life and recycled according to local regulations.

Specifications

1x Air Tube
1x Inflating Needle
2x Inflation Nozzles
1x Pesta valve
1x Charging Cable
1 Storage Bag
1x User Manual

Product Overview

1. Air Tube
2. Charging Port
3. Light
4. Screen Display
5. Unit Display
6. Lighting Button
7. Air Pressure – Button
8. Inflation Modes.
9. Battery Indicator Light
10. Function Button R (Unit/Mode Switch)
11. Power Button
12. Air Pressure + Button

Recommended Inflation Pressure

Button Operation Instructions

1. Power Button: Press and hold the power button for 2s, and the air pump will turn on and enter standby mode; short press again to start inflating; after inflating (the air pump will automatically stop inflating when the air pres- sure reaches the preset value), press and hold the power button for 2s to shut down.
2. Function Button R: Short press to set different inflatable objects (cars, motorcycles, bicycles, balls). Each time you press it the air pressure display will flash 3 times and then it will default to the selected setting object. Press. and hold the function button R for 2s to switch between PSI, BAR, KPA, and Kg/cm2.
3. Lighting Button: Short press to turn on the lighting, press again to enter SOS, and press again to tum it off.
4. Air Pressure + Button: Each time you press t, the air pressure value will increase accordingly.
5. Air Pressure – Button: Each time you press it the air pressure value will decrease accordingly.

Screen Display Description

1. Long press the power button for 25, the screen display will ight up, and then the display will stay on the car icon (the default setting forfirst use).If there is not any ooperation within 80s, the screen will automatically turn off.
2. When pressing the function button R to select different inflation objects, the screen will display the preset tire pressure of the corresponding inflation object (Car preset 36PS], Motorcycle preset 34PS], Bicycle preset 45PS|, Basketball preset 8PS, and after flashing 3 times it finally shows “0.0”.
3. Battery Power Display: When the remaining power of the air pump s 10%, the power icon light flashes; when the power exceeds 10%, t’s always on; while charging, it flashes; after fully charged, i’ always on.

Air Pump Using Instructions

1. Connect the Inflation Nozzle: Screw the air pump infla- tion nozze to the tire inflation nozzle (please make sure that the inflation pump is tightened and will not leak).
2. Power On: Press and hold the power button for 2s, the sscreen will light up, displaying the inflation interface, and then the air pump will enter standby state. At this point, press other buttons to make related settings.
3. Set the Inflation Object: Short press the function button R to set the desired inflation object. The soreen will di play the air pressure unit of the corresponding inflation object (press and hold the R button for 2s, 4 air pressure units can be switched freely) and the initial value of air pressure 00.0.
4. Preset Inflation Pressure: Short press the Air Pres- sure +- Button to set the inflation pressure (please set according to the tire pressure value recommended by the car manufacturer).
5. Inflation: When the air pump is in standby mode and has been set correctly, short press the power button to start inflating. The air pump will automatically stop inflating when the preset ai pressure value is reached.
6. Note: When inflating different types of products (such as switching from a car to a bicycle), each time you need toreset the settings before starting the infiation, to avoid setting the preset air pressure value or air pressure unit incorrectly, resulting in inflation accident
7. Remove the Inflation Nozzle: After inflating, press and hold the power button for 25 again to turn off. Unscrew the inflation nozzle to complete the inflation.

Accessories Using Instructions

This air pump comes with an inflation nozzle, an inflating needle, and a Pesta Valve. You can use the corresponding nozzle according to different usage scenarios

1. Take out the required inflation nozzle/inflating needle/Pesta Valve, alignit with the inflation nozzle of the air pump and tighten it to combine them together.
2. Use the same operation steps as “Air Pump Using Instructions” to nflate related items.

Charge the Air Pump

1. Under power-on/off state, insert the charging cable into the air pump USB-C charging port to charge.
2. While charging, the power icon displayed on the screen flashes; after fully charged, it s always on.

FAQ

1. The air pump does not stop when it reaches the pre- set value.

aCheck whether the operation is correct according to the setting instructions. bCheck whether the preset value s correct.

2. On-screen readings are inaccurate or unavailable.

When the tire valve is connected, make sure the screen displays the current tire pressure before turning on the pump.

3.The air pump s running but cannot inflate.

Check if the inflation nozzle is fully connected with the tire valve.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>