venture D616A Heat Diving Warming Vest User Guide

venture D616A Heat Diving Warming Vest User Guide

Product Overview

1. Input connector
2. Nut
3. Battery pocket
4. Haptic feedback receiver
5. LED heat level indicator
6. Wristband remote controller
7. Heating level push button (Heat level control)
8. Heat level indicator lights
9. Li-ion battery
10. Battery connectors (Input & Output)
11. Battery on/off button
12. Battery capacity indicator LED
13. Battery waterproof cover cap
14. Charging terminal

What’s in the box

• Heated Apparel Ix1
  

• Li-ion Battery x2

• Remote Controller x1

• v-splitter Charging Harness x1

• Charging Stand x1

• Battery Charger x1

• USB-C Charging Cable x1

• Extension Panel x1

• Fastening Strap x1

User Guide

Step 1. Plug in and turn on the batteries

Warning: Tighten the nut to avoid damage caused by water seepage.

1. Insert the plug into the battery
   

2. Slide the nut towards the connector
   

3. Turn nut to tighten
   

4. Turn on battery: press and hold the battery button for 2 seconds to turn on the battery.
   

Step 2. Operating your heated dive undercut.

A. Powering ON the suit:

1. On the wristband remote, press and hold the push button for 2 seconds until it indicates 1 LED light (low heat).
   Wristband Remote
   

2. The suit will simultaneously indicate 1 LED light and vibrate once.
   

B. Adjusting the heat level:

1. On the wristband remote, push the button to select your desired heat level
2. For each setting, your remote control will illuminate, and your suit’s haptic feedback receiver will both illuminate and vibrate:
   
   

C. Powering OFF the undercut:

1. On the wristband remote, press and hold the push button for 2 seconds until the indicator lights turn off.
   

2. The LED indicator on the suit will simultaneously turn off and long vibrate once.
   

Charging your Wristband Remote

A. Checking wristband remote battery level:

1. On the wristband remote, click the push button once.
   

2. The indicator light will flash briefly to indicate remaining charge:
   

B. Charging your wristband remote control:

1. Push wristband remote control onto the charging Stand.
   

2. Connect charging dock with USB-C charging cable.

3. Connect USB-C charging cable to an adaptor, and plug into a power outlet.
   

Tip:

1. When your wristband remote’s charge reaches 30%, one of the LEDs will stop flashing (the other two LEDs will continue to flash)
2. At 60% charge, two LEDs will stop flashing (one LED will remain flashing)

Charging your Battery

A. Checking battery status:

1. On the battery, click the push-button once
2. The indicator light will flash briefly to indicate remaining charge:
   

B. Charging batteries:

1. Connect batteries to Y-splitter charging harness.
2. Connect Y-splitter charging harness to charger.
3. Plug the charger into a power outlet.
   

Tip:

1. Your diving undersuit and wristband remote control comes paired from the factory and does not require setup.
2. If at any point your suit does not respond to your remote control, pair your remote control as detailed in Section 5 (next page)

Pairing your Wristband Remote

A. Place your wristband remote within close range (6 inches) of the haptic feedback receiver on your suit

B. Connect ONE battery to your suit while pairing your remote. Do not plug in the second battery for this process.

C. Press and hold the battery’s push button for 2 seconds to switch the battery ON and OFF. Repeat this 3 times slowly with 2 second intervals, and you can expect the following:

1st: Turn on battery. Lights on haptic feedback receiver will show for 2 seconds. Turn off battery.

2nd: Turn on battery. Lights on haptic feedback receiver will show for 2 seconds. Turn off battery.

3rd: Turn on battery. Lights on haptic feedback receiver will flash, indicating that pairing is complete. Tip: If pairing fails, repeat above steps.

Indicator will lash repeated.
Pairing complete.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>