wis network 5G CPE Pro Smart-Home Router User Guide
- June 13, 2024
- wis network
Table of Contents
wis network 5G CPE Pro Smart-Home Router
Product Information
The WIS-AX3000-5G CPE Wireless Router, also known as 5G CPE Pro, is a high- speed wireless router designed for both family and small business use. It provides fast and reliable internet connectivity, allowing users to connect multiple devices simultaneously.
Introduction
Thank you for choosing WIS-AX3000-5G CPE Wireless Router. This Quick Start
Guide is designed to familiarize you with the use of the CPE and describes how
to apply it in your family and small business.
Accessories
- 5G CPE Pro
- Antenna x 4
- Power Adapter x 1
- Quick Start Guide x 1
Hardware Overview
Back Ports
Description | Ports |
---|---|
LTE/5G Antenna | ANT1-4 |
Micro-SIM Card | SIM |
Power Switch | ON/OFF PWR |
LAN Port | LAN 1-4 |
WAN Port | WAN RST |
Ports | Description |
--- | --- |
ANT1-4 | LTE/5G Antenna |
SIM | Micro-SIM Card |
ON/OFF | Power **Switch |
Power on: The power indicator is on Power off: The power indicator is off
PWR| Power Supply DC 12V
LAN 1- 4| LAN 10/100/1000Mbps
WAN| WAN 10/100/1000/2500Mbps
RST| Reset Button
** Press more than 6 seconds to restore factory
Front LEDs:
Description | LEDs |
---|---|
Wi-Fi | On: Available |
Off: Disabled
5G/LTE Signal| 0LED: No Signal
1LED: Weak
2LED: Middle
3LED: Good
4LED: Excellent
Product Usage Instructions
Hardware Installation:
Inserting Micro-SIM Card:
Insert a micro SIM card into the SIM card slot at the top of the CPE.
NOTE:
- Insert the micro SIM card into the slot, following the direction indicated by the silk screen (notch facing in).
- Do not insert or remove the SIM card when the CPE is powered on.
Connecting to the Local Power Supply
- Connect the power adapter to the power port of the CPE.
- Ensure that each LED on the device indicates normal startup.
Use the power adapter to connect the power port of the CPE to the local power
source.
NOTE: Observe the status of each LED to judge whether the device starts
normally.
Connecting to the Network Device:
-
Connection through Wireless Network: The Internet access device can be connected to the CPE via the wireless network. The default WLAN SSID for both Wi-Fi 2.4G and Wi-Fi 5G.Internet access device can be connected to CPE through wireless network.
NOTE: Default WLAN wireless network name (SSID) Wi-Fi 2.4G and Wi-Fi 5G. -
Connection through an Ethernet Cable: The Internet access device can be connected to any LAN port of the CPE using an Ethernet cable.
Internet access device can be connected to any LAN port of the CPE through an Ethernet cable.
Configuring the 5G CPE **
**
Configuring the 5G CPE Using the Web-based Interface:
- Connect your Internet access device to any LAN port of the CPE.
- Open a web browser and enter the IP address (192.168.1.1) shown on the nameplate at the bottom of the CPE to access the web management interface. Use “admin” as the default login password.
- Modify the default WiFi settings by accessing the Wi-Fi configuration interface. You can change the SSID and password.
- Set the CPE to Ethernet uplink:
- Connect the WAN interface of the device to the broadband network port of the operator’s home.
- Configure the Internet parameters in the WAN settings of the Web management interface. Please consult your broadband operator for specific Internet parameters.
NOTE: ease consult the broadband operator for specific Internet parameters.
Online Support
For more guides and assistance, please visit
www.wisnetworks.com. You can also contact us via
email at sales@wisnetworks.com. We typically
respond within one weekday.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>