SOUNDPEATS Air4 Earphones Bluetooth 5.3 Hi Res User Guide
- June 13, 2024
- SoundPEATS
Table of Contents
Air4
WIRELESS EARBUDS
User Guide
First Time of Use
- Open the lid of the charging case, press and hold the button on the charging case for 3 seconds until the indicator light on the charging case flashes white. At this point, they enter into pairing mode.
- Turn on your device’s Bluetooth and select SOUNDPEATS Air4 from the Bluetooth list to complete the pairing.
Multi-point Connection
SOUNDPEATS Air4 earphones can be paired simultaneously with two devices.
How to connect: Once the earphones are paired with device A, turn off the
Bluetooth of device A. Repeat the pairing operation to connect the earphones
to device B. When the pairing is completed, please turn on the Bluetooth of
device A to complete the pairing.
Reset
- Place both earphones back into the charging case, and make sure they are correctly placed.
- With the case lid open, press and hold the button of the charging case for 10S until the indicator light on the charging case flashes white twice.
- Close the case lid and take out the earphones, and they are activated successfully.
Wearing methods
- Identify the left and right earphones.
- Adjust the earphones to fit your ears.
Product Diagram
Controls
Power On| Auto: Open the charging case; the earphones turn on automatically
Manually: Press and hold the multifunctional button for 1.5s, with earphones
off
---|---
Power off| Auto: Place the earphones back into the charging case and close the
case lid
Manually: Press and hold the multifunctional button for Ids, with earphones on
Play/Pause| Double-tap on the multifunctional button
Volume-| Single-tap on the left multifunctional button
Volume+| Single-tap on the right multifunctional button
Next Track| Press and hold the right multifunctional button for 1.5s
Noise Reduction Mode / Normal Mode Switching| Press and hold the left
multifunctional button for 1.5s
Answer/Hang Up a Phone Call| Double-tap on the multifunctional button
Reject a Phone Call| Press and hold the multifunctional button for 1.5s
Switch Between Two Active Calls| Press and hold the multifunctional button for
2s
Manual Pairing| Press and hold the button of the charging case for 3s
Activate/Deactivate the Voice Assistant| Press the right multifunctional
button for three times
Activate/Deactivate the Game Mode| Press the left multifunctional button for
three times
Q&A
Q1: What does the indicator light of the charging case display?
1. The battery life of the charging case:
| 100%—50% | Green |
|---|---|
| 49%-10% | Yellow |
| <10% | Red |
2. 2)Charging status of the charging case:
| <20% | The Red light flashes slowly |
|---|---|
| 20%-69% | The Yellow light flashes slowly |
| 70%-99% | The Green light flashes slowly |
| 100% | The Green light stays on |
Q2: How to charge the charging case?
- Connect the charging case to a Type-C charger. (The current does not exceed 1A).
- If the earphones stay idle for an extended period, charge them at least every three months to prevent the battery from being damaged.
Q3: Why are the earphones still connected to the phone when they are put back to the charging case and the case lid is closed?
- Check whether the charging case has battery power. If it has run out of battery, closing it will not disconnect the earphones from the device.
- Ensure the earphones are properly placed in the charging case and the charging metal sheet and PIN are clean. And wiping clean the contact points on the earphones and the charging case should fix this issue.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC ID
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference thatmay cause undesired operation of the device.”
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Room 1308-1309, Building B, Huihai Square,
Chuangye Road, Longhua District,
Shenzhen, China. 518109
support@soundpeats.com
www.soundpeats.com
FCC ID: 2AFTU-DD024 IC ID: 27785-AIR3
MADE IN CHINA Company：Qing UG(haftungsbeschränkt)
Address：Undinestr. 7, 12203 Berlin Germany
TANMET INT’L BUSINESS LTD
9 Pantygraigwen Road, Pontypridd,
Mid Glamorgan, CF37 2RR,UK
tanmetbiz@outlook.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>