ELATION PROFESSIONAL KL Fresnel 6 CW PO 150W Cool White LED 6 Inch Pole Operated Fresnel User Manual

ELATION PROFESSIONAL KL Fresnel 6 CW PO 150W Cool White LED 6 Inch Pole

Operated Fresnel

Product Information

The KL FRESNEL 6 CW PO is a professional lighting fixture manufactured by Elation Professional. It is a fresnel light with a cold white color temperature. The product is designed for use in various lighting applications and is equipped with several features and controls.

Product Usage Instructions

Before operating the KL FRESNEL 6 CW PO, please read and understand the instructions provided in this manual. It contains important safety precautions and guidelines for proper use.

General Information

• Ensure that only trained personnel operate this device.
• This device is not suitable for private use.

Box Contents

• Rotating Barn Doors (x1)
• Junior Pin (x1)
• Gel Frame (x1)
• Locking Power Cable (x1)

Customer Support Contact ELATION Service for any product-related service and support needs. You can also visit the forums.elationlighting.com for questions, comments, or suggestions.
ELATION SERVICE USA – Monday to Friday, 8:00 am to 4:30pm PST
Phone: 323-582-3322 | Fax: 323-832-9142 | Email:
support@elationlighting.com
ELATION SERVICE EUROPE – Monday to Friday, 08:30 to 17:00 CET
Phone: +31 45 546 85 63 | Fax: +31 45 546 85 96 | Email:
support@elationlighting.eu

Replacement Parts For replacement parts, please visit parts.elationlighting.com.

Warranty
Elation Professional provides a limited warranty for this product. Any modifications, repairs, or damages resulting from disregarding safety instructions will void the warranty.

©2022 ELATION PROFESSIONAL all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ELATION PROFES-SIONAL logo and identifying product names and numbers herein are trademarks of ELATION PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-ELATION brands and product names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent assembly, installation, rigging, and operation of this product.

• Elation Professional USA | 6122 S. Eastern Ave. | Los Angeles, CA. 90040
  323-582-3322 | 323-832-9142 fax | www.elationlighting.com | info@elationlighting.com

• Elation Professional B.V. | Junostraat 2 | 6468 EW Kerkrade, The Netherlands
  +31 45 546 85 66 | +31 45 546 85 96 fax | www.elationlighting.eu | info@elationlighting.eu

• Elation Professional Mexico AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000 +52 728-282-7070

DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this document may be available online.
Please check www.elationlighting.com for the latest revision/update of this manual before beginning installation and/or programming.

Date| Document Version| Software Version| DMX Channels| Notes
---|---|---|---|---
06/26/2020| 1.0| 1.03| 1/2/3/4/5 ch.| Initial Release

10/26/2022

| ****

1.1

| ****

1.04

| ****

No change

| Added RDM; updated Installation Instructions, System Menu, Encoder Knob, DMX Traits

GENER AL INFORMATION

INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use infor-mation. This device is intended for use by trained personnel only, and is not suitable for private use.

UNPACKING

Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all accessories neces-sary to install and operate the device have arrived intact. In the event that damage has been found or parts are missing, please contact our customer support team for further instructions. Please do not return this device to your dealer without first contacting customer support. Please do not discard the shipping carton in the trash. Please recycle whenever possible.

BOX CONTENTS

• Rotating Barn Doors (x1)
• Junior Pin (x1)
• Gel Frame (x1)
• Locking Power Cable (x1)

CUSTOMER SUPPORT

Contact ELATION Service for any product related service and support needs. Also visit forums.elationlighting.com with questions, comments or suggestions.
ELATION SERVICE USA – Monday – Friday 8:00am to 4:30pm PST 323-582-3322 | Fax 323-832-9142 | support@elationlighting.com
ELATION SERVICE EUROPE – Monday – Friday 08:30 to 17:00 CET +31 45 546 85 63 | Fax +31 45 546 85 96 | support@elationlighting.eu

REPLACEMENT PARTS – please visit parts.elationlighting.com
THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAM-AGES RESULTING FROM MODIFICATIONS TO THIS FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.

LIMITED WARRANTY

• A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years (730 days), and Elation Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship for a period of six months (180 days), from the original date of pur-chase. This war-ranty excludes discharge lamps and all product accessories. This warranty shall be valid only if the product is purchased within the United States of America, including posses-sions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
• B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return shipping charges only to a designated point within the United States. If any product is sent, it must be shipped in its original package and packag-ing material. No accessories should be shipped with the product. If any acces-sories are shipped with the product, Elation Professional shall have no liability what so ever for loss and/or or damage to any such accessories, nor for the safe return thereof.
• C. This warranty is void if the product serial number and/or labels are altered or removed; if the prod-uct is modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional; if the product is damaged because not properly maintained as set forth in the product instructions, guidelines and/or user manual.
• D. This is not a service contract, and this warranty does not include any maintenance, cleaning or periodic check-up. During the periods as specified above, Elation Professional will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this war-ranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.
• E. Elation Professional reserves the right to make changes in design and/or performance improve-ments upon its products without any obligation to include these changes in any products thereto-fore manu-factured.
• F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the products described above. Except to the extent prohibited by applicable law, all implied war-ranties made by Elation Professional in connection with this product, including warranties of mer-chantability or fitness, are limited in duration to the warranty periods set forth above. And no war-ranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said periods have expired. The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional be liable for any loss and/or damage, direct and/or consequential, arising out of the use of, and/or the inability to use, this product.
• G. This warranty is the only written warranty applicable to Elation Professional products and super-sedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

WARRANTY RETURNS

All returned service items whether under warranty or not, must be freight pre- paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem, as well as the R.A. number, must also be writ-ten down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without an R.A. number clearly marked on the out-side of the package will be refused and returned at customer’s expense. You may obtain an R.A. number by contacting customer support.

SAFETY GUIDELINES

This fixture is a sophisticated piece of electronic equipment. To guarantee a smooth opera-tion, it is important to follow all instructions and guidelines in this manual. Elation Profes-sional is not responsible for injuries and/or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. Only qualified and/or certified personnel should perform installation of this fixture and only the original rigging parts in-cluded with this fixture should be used for installation. Any modifications to the fixture and/or the included mounting hardware will void the original manufacturer’s warranty and in-crease the risk of damage and/or personal injury

• PROTECTION CLASS 1 – FIXTURE MUST BE PROPERLY GROUNDED.
• THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY. DAMAGES RESULTING FROM MODIFICATIONS TO THIS
• FIXTURE AND/OR THE DISREGARD OF SAFETY INSTRUCTIONS AND GUIDELINES IN THIS MANUAL VOID THE MANUFACTURER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR REPAIRS.
• DO NOT PLUG FIXTURE INTO A DIMMER PACK!
• NEVER OPEN THIS FIXTURE WHILE IN USE!
• UNPLUG POWER BEFORE SERVICING FIXTURE!
• NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
• KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
• NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
• RETINA INJURY RISK – MAY INDUCE BLINDNESS!
• SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
• DO NOT EXPOSE THIS UNIT TO RAIN AND/OR MOISTURE! THIS FIXTURE IS INTENDED FOR USE IN DRY, INDOOR ENVIRONMENTS ONLY!
• DO NOT TOUCH the fixture housing during operation. Turn OFF the power and allow ap-proximately 15 minutes for the fixture to cool down before servicing.
•  DO NOT expose the fixture to rain or moisture, or spill liquids into or onto the fixture! The fixture is intended for use in dry, indoor environments only!
• DO NOT shake fixture, and avoid using brute force when installing and/or operating the fixture.
• DO NOT operate the fixture if the power cord is frayed, crimped, damaged, and/or if any of the power cord connectors are damaged and do not plug into the fixture securely with ease.
• NEVER force a power cord connector into the fixture. If the power cord or any of its con-nectors are damaged, replace it immediately with a new one of the same power rating.
• DO NOT block any air ventilation slots.
• All fan and air inlets must remain clean and never blocked.
• Leave approx. 6” (15cm) between the fixture and other devices or a wall in order to allow for proper cooling.
• When installing fixture in a suspended environment, always use mounting hardware that is no less than M10 x 25 mm, and always install fixture with an appropriately rated safety cable.
• Always disconnect the fixture from the main power source before performing any type of service and/or cleaning procedure.
• Only handle the power cord by the plug end. Never pull out the plug by tugging on the wire portion of the cord.
• During the initial operation of this fixture, a light smoke or smell may emit from the inte-rior of the fixture. This is a normal process and is caused by excess paint in the interior of the casing burning off from the heat associated with the lamp. This will decrease gradually over time.
• Consistent operational breaks will ensure fixture will function properly for many years.
• ONLY use the original packaging and materials to transport the fixture for service.

MAINTENANCE

DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!

CLEANING
Frequent cleaning is recommended to ensure proper function, optimized light output, and an extended life. The frequency of cleaning depends on the environment in which the fixture operates: damp, smoky, or particularly dirty environments can cause greater accumulation of dirt on the fixture’s optics. Periodically clean the external lens surface with a soft cloth to avoid dirt/debris accumulation. NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an autho-rized Elation service technician. Should you need any spare parts, please order genuine parts from your local Elation dealer.
Please refer to the following points during routine inspections:

• A detailed electrical check by an approved electrical engineer every three months, to make sure the circuit contacts are in good condition and prevent overheating.
• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out during normal operation, resulting in damage or injury as larger parts could fall.
• Check for any deformations on the housing, color lenses, rigging hardware, and rigging points (ceiling, suspension, trussing). Deformations in the housing could allow for dust or moisture to enter into the fixture. Damaged rigging points or unsecured rigging could cause the fixture to fall and seriously injure a person(s).
• Electric power supply cables must not show any damage, material fatigue, or sediments.
• NEVER remove the ground prong from the power cable.

OVERVIEW

1. Barn Door Installation Slots
2. Mounting Yoke
3. Clamp Mounting Point
4. Junior Pin (installed)
5. Tilt Adjustment Knob
6. Pan Adjustment Knob
7. Dimmer Adjustment Knob
8. Enter Button
9. Display Screen
10. Down Button
11. Up Button
12. Mode Button
13. Zoom Adjustment Knob
14. Safety Cable Rigging Point
15. Service Port
16. Fuse – T3A / 250V
17. Power In
18. Power Out
19. 3-pin DMX In
20. 5-pin DMX In
21. 3-pin DMX Out
22. 5-pin DMX Out

INSTALL ATION GUIDELINES

• FLAMMABLE MATERIAL WARNING
  Keep fixture minimum 5.0 feet (1.5m) away from flammable materials and/or pyro-technics.

• ELECTRICAL CONNECTIONS
  A qualified electrician should be used for all electrical connections and/or installa-tions.

• USE CAUTION WHEN POWER LINKING OTHER MODEL FIXTURES, AS THE POWER CONSUMPTION OF OTHER MODEL FIXTURES MAY EXCEED THE MAX POWER OUTPUT ON THIS FIXTURE. CHECK SILK SCREEN FOR MAX AMPS.

• DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!

• Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.

• Before rigging/mounting a single fixture or multiple fixtures to any metal truss/structure or placing the fixture(s) on any surface, a professional equipment installer MUST be consulted to determine if the metal truss/structure or surface is properly certified to safely hold the com-bined weight of the fixture(s), clamps, cables, and accessories.

• Ambient operating temperature range for this fixture is 14°F to 113°F (-10°C to 45°C). Do not operate the fixture when the ambient temperature falls outside of this range.

• Fixture(s) should be installed away from walking paths, seating areas, or areas were unauthor-ized personnel might reach the fixture by hand.

• NEVER stand directly below the fixture(s) when rigging, removing, or servicing.

• Overhead fixture installation must always be secured with a secondary safety attachment, such as an appropriately rated safety cable that meets all local, national, and country codes and regulations.

• Allow approximately 15 minutes for the fixture to cool down before servicing.

INSTALL ATION GUIDELINES CLAMP INSTALLATION

This fixture includes an adjustable mounting yoke with an integrated clamp mounting point, as well as an additional safety cable rigging point attached to the body of the fixture (see the illustration below). When mounting this fixture to truss, be sure to secure an appropri-ately rated clamp (not included) to the clamp mounting point on the yoke and attach a sepa-rate SAFETY CABLE of the appropriate rating (not included) to the safety cable rigging point on the fixture.

SAFETY CABLE:
ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED ENVIRONMENT TO ENSURE THAT THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.

RIGGING

Overhead rigging requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the fixture, among other skills. If you lack these qualifications, do not attempt the installa-tion yourself. Improper installation can result in bodily injury.
The fixture is fully operational in the following positions: hanging from a horizontal truss, suspended sideways from a vertical truss, or standing upright on a flat, level surface. See the illustration below for reference .

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting and moving head fixtures, and lasers, which are focused directly towards the exterior housing and/or penetrate the front lens opening of Elation lighting fixtures, can cause severe internal damage including burning of optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts, wiring, discharge lamps, and LEDs.
This issue is not specific only to Elation lighting fixtures, but rather it is a common issue with lighting fixtures from all manufacturers. Although there is no true way to fully prevent this issue from happening, the guidelines below can reduce the risk of potential damage. Contact Elation Service for more details.
DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT SUNLIGHT, OTHER LIGHTING OR MOVING HEAD FIXTURES, AND LASERS DURING UNPACKING, INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS. DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

GEL FRAME
This fixture includes a removable gel frame, which can be installed by following the steps shown below.

1. Release the lock on the lens frame latch, and flip the latch upward
2. Slide the gel frame into place in the slot in front of the fixture lens.
3. Flip the lens frame latch back down, making sure it clicks securely into place

BARN DOORS
This fixture includes removable set of barndoors, which can be installed by following the steps shown below.

1. Release the lock on the lens frame latch, and flip the latch upward
2. Slide the barndoors into place in the slot in front of the fixture lens and gel frame.
3. Flip the lens frame latch back down, making sure it clicks securely into place
4. Unfold the barndoors by carefully pulling the panels outwards

REMOTE DEVICE MANAGEMENT

NOTE : In order for RDM to work properly, RDM enabled equipment must be used throughout the entire system, including DMX data splitters and wireless systems.

• Remote Device Management (RDM) is a protocol that sits on top of the DMX512 data standard for lighting, allowing the DMX systems of the fixtures to be modified and monitored remotely. This protocol is ideal for instances in which a unit is installed in a location that is not easily accessible.
• With RDM, the DMX512 system becomes bi-directional, allowing a compatible RDM enabled controller to send out a signal to devices on the wire, as well as allowing the fixture to respond (known as a GET command). The controller can then use its SET command to modify settings that would typically have to be changed or viewed directly via the unit’s display screen, including the DMX Address, DMX Channel Mode, and Temperature Sensors.

FIXTURE RDM INFORMATION:

22A6

| ****

0000-FFFF

| ****

1035

| 01        Dimmer

02        16Bot

03        3Ch

04        Standard

05        Extended

Please be aware that not all RDM devices support all RDM features, and therefore it is important to check beforehand to ensure that the equipment that you are considering includes all of the features that you require.

The following parameters are available on this device:

CONTROL PANEL

The fixture includes an easy to navigate system menu. The control panel (see image below) located on the side of the fixture provides access to the main system menu, where all neces-sary system adjustments can be made. During normal operation, pressing the MODE button once will access the fixture’s main menu. From the main menu, you can navigate through the different functions and access the sub-menus with the UP and DOWN buttons. Once you reach a field that requires adjusting, press the ENTER button to activate that field, then use the UP and DOWN buttons to adjust the field. Pressing the ENTER button once more will confirm your setting. You may exit the main menu at any time without making any adjustments by pressing the MODE button.
The display screen will automatically turn off after 30 seconds of inactivity .

SYSTEM MENU

ELATION KL FRESNEL 6 CW PO SYSTEM MENU

Supports Software Versions: 1.04
Features subject to change without notice.

Rotation direction (clockwise/counter-clockwise) and control of effects depend on head orientation and pan/tilt settings.

Default settings listed in bold.

MAIN MENU| SUB MENU| OPTIONS / VALUES| DESCRIPTION
ADDRESS| Address: xxx| 001 – 511| Set DMX address

USER MODE

| Dimmer|
Dimmer 16bit|
3CH|
Standard|
Extended|

FUNCTION

| Status| Lost DMX| Black / Hold|

LCD Set

| Display| On / Off| 30s screen saver setting
Key Lock| On / Off| Display menu button lock
Flash| On / Off| Display flashes when no signal is detected
Invert| On / Off| Flip screen display 180 deg
Temp C / F| C / F| Set temperature units

Dim Mode

| Standard|
Stage|
TV|
Architec|
Theatre|
Stage 2|
0.0s|
0.1s|
…|
10s|

Disp Set

| ADDR|
Disp Ch|
Secondry|

Fan Set

|

LED Fan

| Auto|
High|
Low|

Dim Curve

| Linear|
Square|
Inv Square|
S Curve|

Frequen

| 900 Hz, 1000 Hz, 1100 Hz, 1200 Hz, 1300

Hz, 1400 Hz, 1500 Hz, 2500 Hz, 4000 Hz,

5000 Hz, 10 KHz, 15 KHz, 20 KHz, 25 KHz

|

FUNCTION

(continued)

| USB Data| On / Off| Power on USB port to update device
Primary| On / Off| Primary mode switch
DFSE| On / Off| Reset to default settings

INFO

|

Time Info

| Current| Current run time (hours)
Total| Fixture total run time (hours)
Last| Run time since last cleared (hours)
Clear| On / Off| Password = 050/60
Temp Info| LED Temp| xxx C / xxx F|
Err Info| None, …|
Model Inf| KL F6 CW PO|
Software| Vx.xx|
TEST| Man Ctrl| Dimmer| 000 – 255|
Strobe| 000 – 255|

FAN CONTROL
The KL Fresnel 6 CW PO is a high-performance fixture suited for multiple applications. For noise critical environments such as Theater, Opera, or Orchestral Halls, it offers various fan operation modes which remove unwanted noise distractions for the audience and performers. Fan Modes can be changed remotely via the DMX control channel, allowing the fixture to offer high output or whisper-silent operation at a moment’s notice. All Fan Modes smoothly transi-tion over a brief period, preventing unwanted attraction to the fixture.

• Auto (Default) – Fans only run at the speeds needed to keep the LED engine within a safe temperature range, and ensures optimal performance of the fixture. They will turn off if pos-sible; for example, when the fixture is dimmed to a low intensity. Fans sense the ambient and fixture temperature and will, at all times, try to keep noise levels at a minimum. The fixture output will only be reduced when the LED engine cannot be cooled to its safe operating range due to a high ambient temperature.
  NOTE: This mode is recommended for daily operation.

• High – Fan speeds are increased throughout the fixture for the most efficient cooling. This mode will increase wear on the fans and should only be utilized in exceptional circumstances. Fans will always run, even if the fixture is dimmed. Fixture output is kept at 100% unless the LED engine temperature reaches an unsafe temperature, at which point the fixture will re-duce power carefully to ensure continued safe operation. This mode is only required in very high ambient temperatures when automatic fan speed adjustments are not desired.

• Low – For very critical noise environments, the fixture offers two additional Low Noise Modes for silent operation. The fixture output will be reduced, yet due to the extremely high lumi-nous flux, the fixture still offers outstanding performance. All parameters of the fixture oper-ate more quietly with reduced fan speeds. Almost all fixture fans are turned off, and only run when absolutely necessary. The fixture LED power output is reduced to 50%.

ENCODER KNOB

• This device features an encoder knob located on the side panel beside the display screen, as shown in the illustration above.
• This knob allows the user to quickly enter Manual Dimmer Mode by pressing on the knob. The dimming can then be adjusted by turning the knob. To exit Manual Dimmer Mode, use the dis-play screen control buttons to navigate to “User Mode” in the main system menu, and change the user mode to another mode.
• Additionally, the user can press and hold the encoder knob for 10 seconds to activate full output for 1 minute. This feature can be used to aid in aiming and/or positioning the fixture, and overrides any DMX-controlled operations.

DMX TRAITS

ELATION KL FRESNEL 6 CW PO DMX CHANNEL TRAITS

Supports Software Versions: 1.04
Features subject to change without notice.

Rotation direction (clockwise/counter-clockwise) and control of effects depends on head orientation and pan/tilt settings.

CHANNEL| DMX VALUES|

FUNCTION

Dimmer| Dimmer 16bit| 3CH| Standard| Extended
1| 1| 1| 1| 1| 000 – 255| Dimmer Intensity, 0% to 100%
 | 2|  | 2| 2| 000 – 255| Dimmer Intensity Fine
 |  |

2

|

3

|

3

|  | Strobe
000 – 031| LED Off
032 – 063| LED On
064 – 095| Strobe Effect, slow to fast
096 – 127| LED On
128 – 159| Pulse Effect, slow to fast
160 – 191| LED On
192 – 223| Random Strobe Effect, slow to fast
224 – 255| LED On
 |  |

3

|

4

|

4

|  | Dimmer Modes
000 – 020| Standard
021 – 040| Stage
041 – 060| TV
061 – 080| Architectural
081 – 100| Theatre
101 – 120| Stage 2
 | Dimmer Delay Time
121| 0.0s
122| 0.1s
123| 0.2s
124| 0.3s
125| 0.4s
126| 0.5s
127| 0.6s
128| 0.7s
129| 0.8s
130| 0.9s
131| 1.0s
132| 1.5s
133| 2.0s
134| 3.0s
CHANNEL| DMX VALUES|

FUNCTION

---|---|---
Dimmer| Dimmer 16bit| 3CH| Standard| Extended
 |  |

3

|

4

|

4

|  | Dimmer Delay Time (continued)
135| 4.0s
136| 5.0s
137| 6.0s
138| 7.0s
139| 8.0s
140| 9.0s
141| 10.0s
142 – 255| Default
 |  |  |  |

5

|  | Control (hold for 3s)
000 – 100| Idle
 | Refresh Rate
101 – 105| 900 Hz
106 – 110| 1000 Hz
111 – 115| 1100 Hz
116 – 120| 1200 Hz (default)
121 – 125| 1300 Hz
126 – 130| 1400 Hz
131 – 135| 1500 Hz
136 – 140| 2500 Hz
141 – 145| 4000 Hz
146 – 150| 5000 Hz
151 – 155| 10,000 Hz
156 – 160| 15,000 Hz
161 – 165| 20,000 Hz
166 – 170| 25,000 Hz
171 – 200| Idle
 | Dimmer Curves
201 – 210| Linear (default)
211 – 220| Square
221 – 230| Inverse Square
231 – 240| S-Curve
241 – 255| Idle

DIMMER CURVES

Dimming Curve Ramp Effect

| 0 sec Fade Time| 1 sec Fade Time
---|---|---
255

0

| 255

0

 | Rise Time (ms)| Down Time (ms)| Rise Time (ms)| Down Time (ms)
Standard (default)| 0| 0| 0| 0
Stage| 780| 1100| 1540| 1660
TV| 1180| 1520| 1860| 1940
Architectural| 1380| 1730| 2040| 2120
Theatre| 1580| 1940| 2230| 2280
Stage 2| 0| 1100| 0| 1660

SOFTWARE UPDATES

ONLY QUALIFIED TECHNICIANS SHOULD PERFORM THIS FUNCTION! NOTE ALL MENU SETTINGS BEFORE UPDATING SOFTWARE! FIXTURE SOFTWARE CAN NOT BE DOWNGRADED!
DOWNLOAD FIXTURE SOFTWARE TO PC ONLY! (NO MAC SUPPORT) PLEASE CONTACT ELATION SERVICE FOR FURTHER INFORMATION.

ELATION C-LOADER
An Elation C-Loader can be used to update the fixture to the latest software. Please visit the C-Loader product page at the Elation web site and download the product manual for step by step instructions.
https://www.elationlighting.com/c-loader-software-uploader
To order the C-Loader uploader and the updated software for your fixture, please contact Elation support for details.

STANDARD SERVICE PORT METHOD

1. Copy the updated software onto a USB memory stick.
2. Reset the fixture(s), then insert the USB memory stick directly into the service port of the fixture.
3. In the main menu, navigate to “Personality”, then press ENTER.
4. Navigate to the “Service” sub-menu, then press ENTER.
5. Key in “050” for the password, then press ENTER again.
6. Scroll to the “Yes” option, and press ENTER.
7. Scroll to the desired software file and press ENTER.
8. Select “On” and press ENTER again. The software should now begin copying.

Note : Do NOT interrupt this process, and do NOT remove the USB memory stick until the up-date has been completed and the fixture has automatically reset and returned to the default menu. Failure to follow these guidelines may render your fixture inoperable.

AUTOMATIC SERVICE PORT METHOD
This method can be used when updating software for a single fixture. Does NOT work for updating multiple linked fixtures.

• Copy updated software onto a USB memory stick.
• Switch off power on the fixture, then plug the USB memory stick into the service port.
• Power the fixture on. The data on the memory stick should automatically be detected.
• Use the UP and DOWN buttons to select the desired software file and press ENTER.
• Select “On” and press ENTER. The software should now begin copying.

Note : Do NOT interrupt this process, and do NOT remove the USB memory stick until the up-date has been completed and the fixture has automatically reset and returned to the default menu. Failure to follow these guidelines may render your fixture inoperable.

SPECIFICATIONS

• SOURCE
  • 150W Cool White LED Engine, 5,600K, 97CRI
  • 50,000 Hour Average LED Life*
  • *May vary depending on several factors including but not limited to: Environmental Conditions, Power/Voltage, Usage Pat-terns (On-Off Cycling), Control and Dimming.
• PHOTOMETRIC DATA
  • 8,500+ Total Lumen Output
  • 9,269 LUX 861 FC @ 9.8’ (3m) (Min. Zoom)
  • 2,334 LUX 217 FC @ 9.8’ (3m) (Max. Zoom)
  • Zoom Range 16° – 39°
  • Beam Angle 16.1° – 38°
  • Field Angle 39.1° – 53.9°
• EFFECTS
  • Manual Zoom
  • Electronic Dimmer and Strobe
  • Variable 16-bit Dimming Modes and Curves
• COLOR
  • 5,600K Cool White LED
• CONTROL / CONNECTIONS
  • Manual and DMX Controlled Dimmer and Shutter
  • Dimmer and Zoom Rotary Dials
  • (5) DMX Channel Modes (1 / 2 / 3 / 4 / 5)
  • 4 Button Control Panel LCD Menu Display
  • RDM (Remote Device Management)
  • 3/5pin DMX and IP65 Locking Power Cable In/Out
  • With Wired Digital Communication Network
• SIZE / WEIGHT
  • Length: 13.5” (344mm)
  • Width: 10.75” (273mm)
  • Vertical Height: 15.47” (393mm)
  • Weight: 18.5 lbs. (8.4kg)
• ELECTRICAL / THERMAL
  • AC 100-240V – 50/60Hz
  • 180W Max Power Consumption
  • 5°F to 113°F (-15°C to 45°C)
  • Power Linking: 6Pcs @ 110V / 14Pcs @ 240V

APPROVALS / RATINGS
CE | cETLus | IP30

DIMENSIONAL DRAWINGS

FIXTURE WITH JUNIOR PIN INSTALLED

BARN DOOR AND JUNIOR PIN INSTALLED

ERROR CODES

ERROR CODES

Error codes are subject to change without any prior written notice.

ERROR CODE| DESCRIPTION
Temp error| Error with LED temperature.

When the unit is powered on, it will automatically enter a “Reset/Test” mode, in which the unit runs a brief self-evaluation. If an internal problem is detected, an error code will flash in the be displayed. These codes are listed in the table below.

References

• Topics | Elation Lighting Forums
• Elation Professional EUROPE - Professional Lighting Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>