JAMARA 410190 Aeroplane 2.4 GHz Gyro 2CH-Remote Controlled Instructions

JAMARA 410190 Aeroplane 2.4 GHz Gyro 2CH-Remote Controlled

Product Information

• Product Name: Cessna 182 2,4GHz
• Manufacturer: JAMARA e.K.
• Model Number: 410190
• Frequency Bands: 2.4 GHz
• Frequency Range: 2420 MHz – 2465 MHz
• Maximum Power Transmitted: <2 mW
• Age Recommendation : Suitable for ages 16 and above
• Certification: Complies with Directive 2014/53/EU, 2011/65/EU

Product Usage Instructions

• Safety Precautions:
  • This product is not a toy and is not suitable for children under 36 months.
  • The product contains small parts that can be swallowed, posing a risk of suffocation. Keep it away from children.
  • Individuals with reduced physical sensory, mental abilities, lack of experience, and/or knowledge should not use the device unless supervised by someone who knows how to operate it safely.
  • Read and understand all warning and safety instructions before using the model.
• Assembly:
  • Follow the provided assembly instructions to correctly assemble the Cessna 182 model.
• Charging:
  • Ensure that the product is turned off before charging.
  • Connect the provided charger to the model’s charging port.
  • Follow the recommended charging time mentioned in the user manual.
  • Do not leave the product unattended while charging.
• Operation:
  • Before operating the model, ensure that you have read and understood the complete user manual.
  • Familiarize yourself with the controls and functions of the model.
  • Choose a suitable area for flying the model, making sure to comply with local regulations and safety guidelines.
  • Turn on the model and the remote control following the instructions in the user manual.
  • Use the remote control to control the movement of the model, such as ascending,\ descending, turning, and maintaining altitude.
  • Avoid flying in restricted areas or near people, animals, or objects.
  • Follow the recommended flight time and avoid overusing the model to prevent damage.
• Maintenance and Care:
  • Regularly inspect the model for any signs of damage or wear.
  • Clean the model after each use and remove any debris or dirt.
  • Store the model in a cool and dry place when not in use.
  • Follow the maintenance instructions provided in the user manual to ensure the longevity of the product.

For more detailed instructions and crucial information, please refer to the complete user manual available at: www.jamara-shop.com/Conformity.

General information

JAMARA e.K. is not liable for any damage caused to the product itself or through this, provided this is due to improper operation or handling errors. The Customer alone bears the full responsibility for the proper use and handling, including without limitation, the assembly, the charging process, the use and choice of the operation area. Please refer to the operating and user instructions, it contains important information and warnings.

Suitable from 16 years! Not a toy!
Warning: – Not suitable for children under 36 months.

RISK OF SUFFOCATION!

• Contains small parts which can be swallowed.
  Keep away necessarily from children.

• This device is not intended for use by individuals (Including children) with reduced physical sensory, mental abilities, lack of experience and / or knowledge, unless they are supervised in how the device is to be used.

Certificate of Conformity
Hereby JAMARA e.K. declares that the product „Cessna 182, No. 410190 (UAS class 0)“ complies with Directive 2014/53/EU, 2011/65/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address: www.jamara-shop.com/Conformity

• Read the complete instructions and security instructions carefully before using the model.
• Caution! Please fully and carefully read warnings/ safety instructions.
  These are for our own security and can avoid accidents/injuries.

Attention!
Before operating: Switch the model on first then the transmitter.

• In case several models are used at the same time first switch on the model and then the appropriate transmitter. Do not switch on several models or transmitters at the same time as multiple models could react to the same transmitter. When finished: First switch off the model then the transmitter.
• Never operate your model beyond sight. Both the maximum visibility as well as the max. range of your model will depend on many factors such as weather, location and interfering frequencies. Therefore, before each use perform a range test with a second person securely holding the model and also check how the model reacts if there is a signal failure e.g. when empty transmitter batteries are installed.

Assembly

• Connecting the motors
  Connect the 2 connecting cables of the wing with the cables in the fuselage (1). Only connect cables of the same color to each other.

• Wing
  Lay the assembled cables in the recess in the fuselage and take care not to damage the cables when assembling the wing.
  Assemble the wing to the fuselage. Insert the nose into the groove and screw the wing to the fuselage with the screw (2).

• Landing gear installation
  Gently push the landing gear (3) wire into the mounting slot on bottom of the fuselage.

Components

Transmitter:

1. Power LED
2. Throttle Stick
3. Control Stick (left/right)
4. On/Off switch
5. Battery compartment
6. Remove the battery compartment cover.
7. Fit the 2 x AA batteries, observe the correct polarity.
8. Replace the battery cover and lock it.

Battery warning:

• Non-rechargeable batteries are not to be recharged!
• Do not open!
• Do not dispose of in fire!
• Do not mix old and new batteries!
• Do not mix alkaline batteries, standard (carbon-zinc) or rechargeable batteries!
• Rechargeable batteries are to be removed from the toy before being charged!
• Rechargeable batteries are only to be charged under adult supervision!
• The supply terminals are not to be short-circuited!

Loading process
Plug the USB cable into the USB charging socket and plug the battery pack into it. The charging time by completely discharged battery pack about 45 minutes.

• USB indicator lights up – battery is being charged
• USB indicator goes out – battery is charged

Warning!
Let the model cool off sufficiently after each use before putting it back into operation. When using an additional batteries let it cool off for minimum 15 minutes until the model is operated again. Overheating can damage the electronics or may result in fire.

Danger!

• The charger is not a toy. Only use the charger supplied.
• The battery may only be charged by or under the supervision of an adult.
• The terminals must not be short-circuited.
• The charger must be checked regularly for damage to the cable, plug, housing and other parts. If any damage is found, the charger must not be used until the damage has been repaired.
• Always disconnect the battery from the charger immediately after charging. Always disconnect the charger from the power supply immediately after disconnecting the battery. Inserting the rechargeable battery or charger after charging will result in damage to the battery, charger or the power supply (fire hazard).

Danger!
If your model has an on/ off switch, always turn off the model immediately after each use. If your model has a removable battery or a disconnectable connector to the battery, the battery should be disconnected from the model immediately after each use. The battery can be deep-discharged by accidentally turning it on or by leaving the battery plugged in. By deep discharge the battery it loses power, can be damaged so much that charging or discharging is no longer possible and the battery can ignite itself during charging or discharging (fire hazard). Never attempt to charge or discharge deep-discharge batteries. The voltage of the battery should never be under 3 volt to avoid a deep discharge. The fully charged battery has a voltage of 4,2 volt. After usage, the intact battery has to be fully charged after a cooling phase of at least 10 min but not longer than 12 hrs. This is to avoid a deep discharge caused by a self-discharge. When not using or storing the battery it has to be checked at least every three months for voltage (min. 3,9 volt) or damage and if necessary charged or disposed.

Binding procedure

1. Switch on the model, the LED starts flashing.

2. Pull the throttle lever on the remote control all the way back and switch on the transmitter.
   The LED on the transmitter flashes.

3. Push the throttle lever all the way forward and back again.
   If the LEDs on the model and transmitter light up at the same time, they are bound.
   When operating multiple models, make sure that you have the right binding. Always connect one model after another.

Takeoff

• Switch on the model and then the transmitter.
• Push the left control stick.
• Walk some steps against the wind and let the plane glide out of your hand in a slight angle with the nose of the plane up.
• Aise the speed to maximum while throwing out the model.
  Attention! If the plane to climb to fast might fall down aircraft.

Climb

• To climb use the throttle stick, push it forwards and the plane climbs. Release and the plane glides.

Turns

• To fly a curve, keep the throttle stick pressed and move the control stick to the left or right.
• If a wide curve is to be flown, briefly touch the control stick for the respective curve.

Decline
Let go both right and left operational sticks at the same time. The motors stop running, the glider will decline by gravity. Be sure of no obstacle when flying to avoid damage to the plane.

Fine tuning the flight behavior

By carefully bending the elevator and rudder, you can fine tune the flight characteristics. Be careful not to bend the material too much, it could be damaged.

1. Bend the horizontal stabilizer upwards, the nose of the aircraft will point downwards.
2. Bend the horizontal stabilizer downward, the nose of the airplane will point upward.
3. Bend the horizontal stabilizer to the left, the aircraft will fly to the right.
4. Bend the vertical stabilizer to the right, the aircraft flies to the left.

Hints
In case of breakages on the model, we recommend to repair/ glue it with a foam adhesive. (Do not use superglue for this purpose)

Spare parts

Battery

Transmitter

Propellers left & right

Landing gear

USB charging cable

Problems and solutions

Transmitter doesn‘t work.

• Power switch is off. – Turn power switch on.

• Batteries are not installed or incorrectly installed. – Make sure batteries are installed correctly.

• Batteries are old or dead. – Replace batteries.
  The prop won‘t spin

• The power switch on the model is off. – Turn power switch on.

• Model are not charged. – Charge the model.
  The model will not gain altitude.

• Batteries are not fully charged – Charge the battery.
  The propellers are damaged. – Replace the propellers.

• Modell is not launched into the wind. – Lauch the model into the wind
  The model loses altitude.

• Batteries are not fully charged. – Charge the battery.
  The model is out of control

• Transmitter is not on. – Turn on the transmitter

• Wind is to strong – Fly the model only in light winds.

• Another radio control with the same frequency is switched on. – Chose another locationto fly

Se curity instructions

Safety instructions for operation

• Warning: Risk of eye injury! Keep a safe distance of at least 1 m.
• Keep hands, hair and loose clothing away from the rotor, not reach into the rotors.
• Never allow anything to come into contact with the rotors. The Outdoor-model can only be flown in good weather. Do not fly in wind, rain or thunder storms.
• Find a place to fly which complies with any laws, and is free from obstacles such as trees, houses and / or other obstacles.
• Do not operate your model near radio stations, power lines, transformer boxes or similar facilities! This can result in radio interference, causing loss of control over the model.
• The model should not be changed in any way, doing so will invalidate the guarantee.
• Do not expose the model or batteries to direct sunlight, always keep them in the shade.
• Never operate the model on rain or over damp surfaces, this may damage the electronics.
• Do not fly in temperatures above + 45° C or below 10° C.
• Protect the model from strong sunlight, moisture and dust.
• Only take off if your battery is full or has sufficient power.
• Be aware that some parts of the model may get hot.
• Never change or modify the model.

Disposal restrictions
Batteries and accumulators must not be disposed of in domestic waste. You are obliged to dispose of batteries (seperate collection) appropriately. After use you can return batteries free of charge to the retail store. As batteries contain substances that can be irritant, can cause allergy and are highly reactive, separate collections and proper recycling is important to the environment and to your health. If the batteries are marked with a chemical symbol Hg, Cd or Pb below the crossed-out waste bin on wheels it refers to that more than 0.0005% of mercury (Hg), more than 0.002% of cadmium (Cd) or more than 0.004% Lead (Pb) is included.

JAMARA e.K.
Inh. Manuel Natterer
Am Lauerbühl 5 – DE-88317 Aichstetten
Tel. +49 (0) 75 65/94 12-0 – Fax +49 (0) 75 65/94 12-23

info@jamara.com ● www.jamara.com
Service – Tel. +49 (0) 75 65/94 12-777
service@jamara.com

References

• jamara.com
• Naslovnica - Net.hr
• jamara.com
• Janus Trade
• Modellbau Zentral - Peter Hofer - Altdorf UR
• Reitter Modellbau & Robotics - Zubehör, Ersatzteile, Bausätze

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>