SYMA X110W Foldable Drone User Manual

X110W FOLDABLE DRONE

User manual

Important safety information

Thank you for purchasing this SYMA product. To ensure that you operate the aircraft correctly and conveniently, please read these instructions carefully before first use and store them in a safe place for future reference.

Safety Guide

1. Please store the smaller-sized drone accessories in places that are out of reach of children.
2. This drone is very powerful. For all first-time flights, the left joystick must be slowly pushed up in order to prevent the drone from ascending too fast to avoid unnecessary collision and possible damage and injury.
3. When the flight is ended, first turn off the power of the remote control. Then turn off the power of the drone.
4. Avoid placing the batteries in places with high temperatures and exposure to heat.
5. Take extra precaution to ensure that the drone is at a minimum distance of 15 feet from the pilot, other people, and animals in order to prevent bodily injury during flight operation. A minimum separation distance of 20 cm must be  maintained between the user’s body and the device under normal use condition.
6. Children under the age of 8 must be instructed in the correct and safe operation of the drone by an adult.
7. The children must be under adult supervision when using this drone.
8. Non-rechargeable batteries are not to be recharged; Batteries are to be inserted with the correct polarity; Different types of batteries or new and used batteries are not be mixed.
9. When the drone is not in use, please remove the batteries in the remote control.
10. The supply terminals are not be short-circuited.
11. Discharge the battery to 40%-50% (On a full charge, fly for half of the total flight time) if it will not be used for 10 days or more, this can greatly extend the battery life.
12. Please keep a safe distance from the spinning propellers to avoid injury.
13. To ensure the electromagnetic environment requirement of the aviation radio (station), using remote controls in the zone, which is in a radius of about 5000m zone from the circle center of the airport runway, is forbidden. All users  also should abide by the regulation of the radio set forth by government and regulatory agencies including the duration and area.
14. Only uses the recommended transformer for the model, and the transformer is not a toy. Check the cord, plug, enclosure and other parts of the transformer regularly. If any damages have been discovered, please immediately stop  using it, until it was completely repaired.
15. Never look steadily at the laser beam since the laser radiation.
16. Attention: Drone assembly under adult supervision.
17. The pilot is responsible for the safe operation and safe distance from uninvolved persons and property on the ground and from other airspace users and shall never fly the drone above crowds (> 12 persons).
18. Open the battery cover of the toy with screwdriver.
19. The packing has to be kept since it contains important information.

Repair and maintenance

1. Use dry and soft cloth to clean this product.
2. Avoid exposing this product to heat.
3. Do not immerse this product in water, otherwise, the electronic parts will be damaged.
4. Check the cord, plug, enclosure and other parts regularly. If any damages have been discovered, please immediately stop using it, until it was completely repaired.

About this product

2.1 Specifications

Drone

Brand Name| SYMA
Model/ITEM NO.| X110W
Drone weight| Approx. 107g
Drone Size| 200x200x103 mm
Motor| ø8
Battery| 3.7V 1100mAh
Charging time| Approx. 100 minutes
Flight time| Approx. 12 mins
Remote control
Operating Frequency| 2.4 GHz
Range| 30m
Battery| 4X1.5V”AA”(Not included)
Package contents
Drone| 1
Remote control| 1
USB charging cable| 1
Propeller| 2 (A/B)
Propeller protector| 4
Screwdriver| 1
Phone holder| 1
User manual| 1

2.2 Install the SYMA Fly app

1. Scan the QR code with your mobile device or download the app from your app store.
   

   http://www.symatoys.com/downshow/syma-fly-android-apk.html| https://itunes.apple.com/us/app/syma- fly/id1306450695?l=zh&ls=1&mt=8

2. SYMA FLY App Connection operation
   ① Install the SMYA FLY app on your phone. Note: Scan the QR code with your mobile device or download it from the app store.
   ② First pair the drone with the remote control, then turn on the WiFi Settings of the mobile device and select FPVWIFI**** from the WiFi list.
   ③ Wait a few seconds until your smartphone connects to the drone’s WiFi network.
   ④ Open the Syma fly application, select the corresponding model, and then click Start, the camera image will be displayed on the screen, indicating that the connection is successful.

2.3 Drone diagram

1. Propeller protector
2. Motor
3. Propellers
4. Battery
5. Camera

2.4 Remote control diagram

1. Power switch
2. Left joystick (press and hold for trimming adjustment and release when finished)
3. Phone holder
4. Right joystick (short press to toggle between high and low speed mode)
5. One-key take off/landing button

Assembling the product

3.1 Removing the Drone
Remove the plastic transparent cover (lift it up), then the battery and the battery locating ring. After, remove the drone from the charging cradle.

3.2 Fixing the propeller

1. Fully unfold the arms of the drone as shown by the arrows.

2. To fix the arms, push inwards the locks at the bottom of the arms.

3.3 Installing the propeller protectors
Insert the back side of the propeller guard into the side of the arm as indicated by the arrow.

3.4 Mobile phone clip installation

3.5 Charging the drone battery

1. To remove the battery, press on the release buttons and at the same time pull out the battery.
2. Connect the USB cable with the charging cradle. After, plug the USB into a power outlet and the charging cradle light will glow red. Insert the battery into the charging cradle and the light will turn green. The light indicator is off when fully charged.
3. Once charging is complete, install the battery into the drone.
   

Battery Warning:

1. Rechargeable batteries should be removed from the toy before being charged.
2. Rechargeable batteries should only be charged under the supervision of adults.
3. Exhausted batteries should be removed from the aircraft.
4. Caution: Risk of explosion if battery is replaced with incorrect ones. Please dispose the batteries according to the instructions.
5. Don’t use or leave the battery near a heat source such as fire or heater.
6. After flying, don’t charge batteries at once to avoid batteries too heat to cause to the fire, make sure it cool down before charging.
7. Don’t hit or let batteries fall down when charging to avoid inner short-circuit.
8. Only use the included adaptor for charging. Please replace with new batteries in time if batteries aging.
9. After full charging, please take off adaptor in time, otherwise batteries will discharge and charge again, this way will shorten batteries service life.
10. The toy is only to be connected to equipment bearing either of the following symbols:

3.6 Instruction of remote control
To insert the controller batteries, open the battery cover on the back of the remote control and insert 4x AA alkaline batteries, ensuring that you observe the polarity markings (batteries are not included and must be purchased separately).

Note:

• When installing the batteries, ensure that you match the + and ‒ ends of the battery with the + and ‒ signs on the controller.
• During the battery installation, it must be ensured that the polarities of the batteries are matched with that of the battery box. No battery shall be installed with the opposite polarity.
• Please do not use new and old batteries together.
• Please do not use different types of batteries together.
• Remote control does not use rechargeable batteries.
• Exhausted batteries are to be removed from the Remote control.

Flight guide

4.1 Flight preparation and turning the drone on/off
Pairing the remote control with the drone

Switch on the remote control Indicator flashes rapidly→ slowly.

The indicator will stay constant when pairing is complete.

  Note:

1. Turn on the drone in the order of ①②③④.
2. After you switch on the remote control, the indicator will flash quickly to indicate that the remote control is waiting to pair with the drone.

Turning the drone on

Note:

1. If the drone is flown out of range from the remote control, the drone indicator light will start to flash and the drone will land slowly.
2. If the remote control suddenly turns off or runs out of power during flight, the drone will automatically land and come to a stop. If the remote control is turned back on during this process, you will be able to control the drone again.

Turning the drone off

Note:
When the drone body tilts more than 90 degrees, the drone shuts down by itself.

4.2 Using the remote controller

Trimming
Trimming forwards and backwards

When the drone is hovering in the air, when it flies forward / backward automatically, you can press and hold the left fine-tuning button and push the right joystick in the backward/forward direction to adjust it until the drone is stable  and then release it.
Trimming left and right

When the drone drifts to the left or right when it is hovering, hold the left joystick down and push the right joystick right/left until the drone stops drifting.

4.3 Function introduction
Under voltage protection

When the two indicators on the nose of the drone begin to flash, it means that the power of the drone is low. At this time, please control the drone to return.

Overcurrent protection

If the drone’s blades collide with another object or become stuck, the drone’s circuit will engage the overcurrent protection mechanism.

4.4 Flight control
Horizontal calibration function
Place the drone on a level surface and move the left and right joysticks to the lower right corner for approximately 3 seconds. The indicator will flash rapidly and then stay constant to indicate that the calibration process is complete.

High/low speed mode
Short press the fast and slow button to switch the fast/slow mode.

1. The default is slow mode when power on.
2. The remote control emits two beeps for fast mode and one beep for slow mode.
   

One-touch take-off/landing

1. When the drone is in standby, press the take-off button to make the drone take off automatically and hover at a height of 1.5 m.
2. When the drone is in the air, press the one-touch take-off/landing button to make the drone land automatically.
   

Altitude hold
When you release the left joystick (throttle) after ascending/descending, the drone will continue to hover at the current height.

Headless mode

In headless mode, push the right joystick of the remote control to fly forward, the drone will always fly in the direction indicated by the nose when it takes off, even if the direction of the nose is changed during the flight.

1. Define the front
   When you turn on the power for the first time and start the drone, the direction of the nose of the drone is straight ahead.

2. Enter and Exit of Headless Mode
   ① After the pairing is completed, short press the “Headless Mode” button, the remote control will emit a “Di Di Di…” sound, and the indicator light on the aircraft will flash slowly, indicating that it has entered the headless state; short press the “Headless Mode” button again. When you hear a long beep of “di”, it will exit the headless state.
   ② In the headless state, the operator does not need to identify the position of the nose of the aircraft, but only needs to control the aircraft according to the direction of the joystick of the remote controller.

3. To define the forward direction function correction
   When the drone collides in the headless state, if it is found that the headless direction is deviated, just land the aircraft to the ground, and after correcting the direction, the drone restarts, the direction the nose points to is straight  ahead in headless mode.

Drone status and maintenance

out of the transmitter’s range.
The drone is unstable when hovering or quickly  drifts in one direction.| Balance calibration is needed| Perform balance calibration.
When in headless mode the forward direction deviates.| Numerous crashes.| Re- set forward direction.
The drone does not hold the set altitude.| 1. Balance calibration is needed.
2. Flying the drone in severe weather.
3. Heavy crash impacts gyroscope calculations.| 1. Perform balance calibration.
2.Avoid flying the drone in severe weather conditions(strong wind, rain, snow, fog, thunder etc).
3. Perform balance calibration.

Contact Us

Please do not hesitate to contact us if you need more further support.
warranty@symatoys.com.cn
**** +1 718-312-0558 (US) +44 (0)7723708421 (UK) +4933545519201(DE)
For online support, please scan this code with Facebook Messenger

https://qrs.ly/stc7z62

Accessories (available separately)

The following section contains a list of optional accessories that are available to purchase.
Accessories can be purchased from your local retailer. Please indicate your preferred colour when making your purchase.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Notice.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference,and
2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a  residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there  is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

“This device complies with FCC radiation exposure limits set forth for general population (uncontrolled exposure).This device must not be collocated or operating in conjunction with any other antenna or transmitter.”
RF frequency band: 2445.0-2475.0MHz
Transmitter power: <3.55dBm
Product name: DRONE
Hereby, [GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO., LTD], declares that this [DRONE ] is in compliance with Directive 2014/53/EU.The full test of the EU declaration of conformity is available at the following internet  address: http://www.symatoys.com/down/-declaration-of-conformity.html

WARRANTY

LIMITED 2-YEAR WARRANTY AND FREE LIMITED REPLACEMENT PARTS FOR 2-YEARS
Symatoys.com.cn warrants to the original buyer only that its products will be free from defects in material and workmanship for 2 years from the date upon which the product is shipped, either directly from symatoys.com.cn or from an  Authorized Re-seller’s location, to the buyer.
The following condition’s must to be eligible for warranty coverage:

1. During the warranty period product is used as intended by the manufacturer.
2. The Product has not been disassembled or modified.
3. The labels and serial numbers show no signs of tampering or altering.
4. Buyer has a warranty code obtained by registering their product online prior to making a claim.

EXCEPTIONS: THE LIMITED WARRANTY SHALL NOT APPLY TO:

• Damage caused by normal wear and tear
• Accident, negligence, abuse, misuse, misapplication or willful damage by buyer (or its agents), or acts of nature
• Crash or burning caused by non-manufacturing factors
• Damage caused by authorized modification or disassembly not authorized by the instruction manual
• Damage. caused by incorrect use or operation
• Damage caused by mismatch or misuse of battery or charger
• Failure of the operator to follow the operating instruction or use outside the products operating parameters
• Damage caused by operating the product in or around electromagnetic interference (i.e., radio transmitting tower, high-voltage wire, substation, etc.)
• Damage caused by operating the product where there may be interference caused by other wireless devices
• Operating the product with load capacity in excess of the sale weight listed in the manual
• Operating the product with aged, damaged or unauthenticated third-party components
• Operating the product with a defective battery

WARRANTY
PROCEDURE: Any claims for breach of the foregoing limited warranty shall only be valid if buyer makes such claim in writing within 2 year of the date of shipment of the product to which the claim. To make a warranty claim, please email warranty@symatoys.com.cn with your full name. address. phone number, order number. vehicle type. part type and purchase date and product issue.

LIMITED REMEDY:
Symatoys.com.cn’s sole liability, and buyer’s sole remedy for any breach of the foregoing warranty shall be at Symatoys.com.cn‘s option to exchange the product with a new product or a refurbished product that is functionally equivalent  to the original product, or issue a credit or refund to the purchase price the product.
Any replaced products shall be warranted as set forth herein, provided that the period within which buyer may make further claims shall be limited to the remainder of the original period.
for the applicable product or 2 years, whichever is longer (although the warranty period shall be suspended during any period of replacement)
DISCLAIMER:

Haftungsausschluss:
THE WARRANTY AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES.
AND Symatyos.com.cn DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  PURPOSE, NON-INFRINGEMENT AND ANY WARRANTIES ARISING OUT OF COURSE OF DEALING, COURSE OF PERFORMANCE AND TRADE USAGE.
Symatoys.com.cn IS NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR UNDER ANY OTHER LEGAL THEORY.  INCLUDING BUT NOT UMITED TO COSS OF USE; LOSS OF REVENUE;
LOSS OF ACTUAL ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS);
LOSS OF THE USE OF MONEY, LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS COSS OF OPPORTUNITY; LOSS OF GOODWILL, LOSS OF EPUTATION; LOSS OF DAMAGE TO COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT OR CONSEQUENTIAL LOSS OR DAMAGE HOWSOEVER CAUSED INCLUDING THE REPLACEMENT OF EQUIPMENT AND PROPERTY.
ANY COSTS OF RECOVERING OR REPRODUCING ANY DATA STORED IN OR USED WITH THE PRODUCT OR ANY FAILURE TO MAINTAIN THE CONFIDENTIALITY OF INFORMATION STORED THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages.
so the above limitation or exclusion may not apply to you. In addition, some states do not allow limitations on how long an implied warranty lasts. so the above limitation may not apply to you.
FREE REPLACEMENT PARTS FOR 2 YEARS: Symatoys.com.cn .com shall also make available any spare part needed for registered vehicles free of charge for 2 years from the date of purchase, with the exception of batteries, motors. circuit boards and transmitters. Shipping charges may apply Limit one part type request per registered vehicle (e.g., registrants are entitled to one extra set of batteries per registered vehicle}. To request spare parts. please email  warranty@symatoys.com with your warranty code, vehicle name/model, current  shipping address, purchase date and part type GET YOUR WARRANTY CODE AT symatoys.com.cn/pages/warranty- signup HAVE YOUR ORDER  NUMBER AND/OR VEHICLE UPC READ

European Representative ：
CET PRODUCT SERVICE LTD.
Osterholzallee 144
71636 Ludwigsburg Germany
Phone：+4971416432236
Email：info.cetservice@gmail.com

British Representative：
CET PRODUCT SERVICE LTD.
Beacon House Stokenchurch Business Park,
Ibstone Rd, Stokenchurch
High Wycombe HP14 3FE UK
Tel： +447419325266
E-mail：info.cetservice@gmail.com

United States Representative：
Duvin Trade Inc 5800 Wood Sorrel Dr，Littleton，Co, 80123， United States
Phone: 718-312-0558
E-mail: amz@symatoys.com

Manufacturer: GUANGDONG SYMA MODEL AIRCRAFT INDUSTRIAL CO.,LTD
Address: NO.2 WEST XINGYE ROAD LAIMEI INDUSTRIAL AREA CHENG HAI , Shantou, China Postal Code: 515800

+1 718-312-0558 (US)
usa@symatoys.com(US) eu@symatoys.com(EU)
http://www.symatoys.com 
+44(0)7723708421 (UK)
usa@symatoys.com(US) eu@symatoys.com(EU)
+49 335-4551-9201(DE)
SYMA is a trademark of Guangdong Syma Model Aircraft Industrial Co., Ltd. registered in the United States and/or other countries.
Made in China

The company has the right of final interpretation of this user manual.

References

• Syma Toys Online Coolest Gadgets for Trendy People – Symatoys
• warranty-signup – Symatoys
• SYMA Official Site
• Declaration Of Conformity - SYMA Official Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>