BaBylissPRO FX825E High Performance LO-Pro Clipper User Manual

Please carefully read the safety instructions before using the appliance.

LO-PRO CLIPPER

FX825E

OPERATING INSTRUCTIONS

1. Before using the clipper for the first time, charge continuously for 3 Maximum battery capa- city will only be reached after 3 charging and discharging cycles.

2. Make sure the switch on the clip- per is in the «0» (OFF) Connect the charging jack into the receptacle on the bottom of the clipper. Plug the adapter into electrical outlet. The charging indicator will light up blue and blink to indicate that the char- ging has begun. Charging is com- plete after 3 hours.

3. The adapter may become warm while This is normal.

4. Preserving the battery: in order to maintain the optimum capa- city of the rechargeable battery, the clipper should be recharged for 3 hours approximately every 6

5. Make sure the switch is in the OFF position when the clipper is not

6. If the charging light starts to flash rapidly (more than 4 flashes per second), the appliance is If this happens, stop charging and remove the adapter from the outlet and contact an authorized service center.

FOR DIRECT PLUG-IN OPERATION

Make sure clipper is off. Connect charging jack into the receptacle at the end of clipper and plug the adapter into power outlet.

ON/OFF SWITCH

To operate, simply slide switch to ON (marked «I»). To stop operation, set to the OFF (marked «0») posi- tion.

VERY IMPORTANT: BLADES MUST BE CLEANED AND OILED ON A REGULAR BASIS FOR PRO- PER FUNCTIONING. FAILURE TO REGULARLY CLEAN AND OIL THE BLADES WILL VOID THE WARRANTY.

USER MAINTENANCE INSTRUCTIONS

MAINTENANCE OF THE BLADE

Always apply oil to the blades be- fore and after use. This will ensure maximum cutting performance and proper maintenance. Hold the clipper away from your body in a downward position and apply a drop of BaBylissPRO lubricating oil on the front and sides of the cutter blade. Wipe off excess oil with a soft, dry cloth.
Do not pull, twist, or wrap the
power cord around the appliance.

HOW TO USE COMB ATTACH- MENTS

To use the comb attachments, turn the clipper to the «0» (OFF) position. Slide the comb attach- ment onto the top of the clipper blade, and then pull down and over the back of the blade. To remove, pull up on the back of the comb attachment and then pull away from the blade.

REPLACEMENT (REMOVAL) OF BLADE SET

Step 1. Unplug the unit and adjust the taper (see position in illustra- tion A)

Step 2. Remove the screws and the fixed blade. Save the screws.
Step 3. Lift off the small moving blade and replace it with the new one on the plastic oscillator (see illustration B).
Step 4. Replace the fixed blade using the screws and lightly tigh- ten them. Adjust the teeth, as shown in illustration C, to a gap

of 1 mm to 1.5 mm. The small, mo- ving blade should be as centered and as parallel as possible to the fixed blade’s teeth.

IMPORTANT NOTE:

The top edge of the fixed blade must be a minimum of 1 mm higher than the top edge of the moving blade and as centered as possible. This is important so that the moving blade does not come in contact with the skin.
Be sure to add a few drops of BaBylissPRO lubricating oil to the blades before running the clipper. Don’t forget to tighten the screws after the blades have been alig- ned.

BLADE SHARPENING

BaBylissPRO cutting blades are ground from the finest quality gra- phite and are hardened to extend the cutting performance. As with any cutting appliance, the cutting edges become dull from repea- ted use. Increasing blade tension

Plastic Oscillator

to force the blade cutting would cause the clipper to overheat and reduce its motor life. When the blade is no longer able to cut smoothly, sharpening is required or replace it with a new BaByliss- PRO blade set.

ADJUSTABLE TAPER LEVER

The taper lever is positioned at your thumb. You can hold the clipper in your hand and adjust the lever while you are clipping.

PRODUCT FEATURES

1. 8 comb
2. Graphite fade blade
3. Speed setting: 6,800 RPM
4. Power adapter
5. LED charge indicator light
6. LED BLUE Blinking – Charging
7. LED BLUE Solid – Fully Charged
8. LED BLUE Flashing – 10 minutes battery left

Discharge time: up to 2.5 hours

CLIPPER CHARGING PRECAUTIONS

• Avoid charging the battery at temperatures below 5°C or above 35°C.
• Avoid charging the battery in direct sunlight or near a radiating heat
• Even though the clipper may not be used for an extended period, charge battery 3 hours every 6 months to maintain
• The power cord cannot be re- placed. If it is damaged, the AC adapter should be

CLIPPER OPERATING PRECAUTIONS

• This clipper has a built-in rechar- geable Do not throw into fire, apply heat, or charge, use, or leave in a high-temperature envi- ronment.

DISPOSAL OF LITHIUM-ION BATTERY

This clipper has a lithium-ion bat- tery. To protect the environment, this battery should be removed and properly disposed of when the unit is no longer operating. To remove the battery block for disposal or recovery, follow these instructions:

1. Disconnect the clipper from household
2. Discharge the battery pack completely before
3. Remove the 3 screws from the top
4. Remove the plastic PCB cover by hand (no screws).
5. Remove the 2 small screws hol-ding the PCB in place.
6. Unplug lithium-ion
7. To protect the environment, do not dispose of the battery with your ordinary household waste. For more details on recovery of material and waste-treatment facilities, please contact the waste disposal services in your

CONTAINS LITHIUM-ION BAT- TERY. MUST BE COLLECTED, RECYCLED OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>