DELL A10 Sliding Rails Installation Guide
- June 13, 2024
- Dell
Table of Contents
DELL A10 Sliding Rails
Product Information
The rail installation guide provides instructions on how to install and remove rails for your system. The rail kit is compatible with square, unthreaded round, and threaded round hole racks. The kit includes sliding rails, velcro straps, screws, and washers. The 1U and 2U rails have identical installation procedures.
Product Usage Instructions
Installing the Rails
- Fully extend the rear sliding bracket of the rail so that the rail is as long as possible.
- Position the rail end piece labeled “FRONT” facing inward and orient the rear end piece to align with the holes on the rear rack flanges.
- Push the rail straight toward the rear of the rack until the latch locks into place.
- For the front end piece, rotate the latch outward pull the rail forward until the pins slide into the flange, and release the latch to secure the rail in place.
- Repeat the preceding steps to install the right rail.
Removing the Rails
- Open the front latch and disengage the rail from the flange.
- Pull the entire rail forward to release the rear end of the rail from the flange.
Before you begin
WARNING: Before you begin, read and follow the safety instructions in
your Safety, Environmental, and Regulatory information document shipped with
your system.
WARNING: To avoid injury, do not attempt to lift the system by yourself.
NOTE: The illustrations in this document do not represent a specific
system.
NOTE: The procedures to install the 1U and 2U rails are identical.
NOTE: This rail kit is compatible with square, unthreaded round, and
threaded round hole racks.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
NOTE: A NOTE indicates important information that helps you make better
use of your system.
Identifying the rail kit contents
A10 sliding rail assembly – 1U systems
- A10 sliding rail (2)
- velcro strap (2)
- screw (4)
- washer (4)
B13 sliding rail assembly – 2U systems
- B13 sliding rail (2)
- velcro strap (2)
- screw (4)
- washer (4)
Installing the rails
To install the left rail:
- Fully extend the rear sliding bracket of the rail so that the rail is as long as possible.
- Position the rail end piece labeled FRONT facing inward andorient the rear end piece to align with the holes on the rear rack flanges.
- Push the rail straight toward the rear of the rack until the latch locks into place.
- For the front end piece, rotate the latch outward pull the rail forward until the pins slide into the flange, and release the latch to secure the rail in place.
- Repeat the preceding steps to install the right rail.
Installing the rear end of the rail
- rear-end latch
Installing the front end of the rail
- front latch
Removing the rails
To remove the rails:
- Open the front latch and disengage the rail from the flange.
- Pull the entire rail forward to release the rear end of the rail from the flange.
Installing the system into the rack
(option A: Drop-In)
- Pull the inner rails out of the rack until they lock into place.
- Locate the rear rail standoff on each side of the system and lower them into the rear J-slots on the slide assemblies.
- Rotate the system downward until all the rail standoffs are seated in the J-slots.
- Push the system inward until the lock levers click into place.
- Pull the blue slide release lock tabs forward on both rails and slide the system into the rack until the system is in the rack.
Installing the system into the rack (Option B: Stab-In)
- Pull the intermediate rails out of the rack until they lock into place.
- Release the inner rail lock by pulling forward on the white tabs and sliding the inner rail out of the intermediate rails.
- Attach the inner rails to the sides of the system by aligning the J-slots on the rail with the standoffs on the system and sliding forward on the system until they lock into place.
- With the intermediate rails extended, install the system into the extended rails.
- Pull the blue slide release lock tabs forward on both the rails, and slide the system into the rack.
- intermediate rail
- inner rail
Securing or releasing the system
-
To secure the system, push the system into the rack until the slam latches engage and lock into the rack.
NOTE: To secure the system for shipment in the rack or in other unstable environments, locate the hard mount captive screw under each latch and tighten each screw using a Phillips #2 screwdriver. -
Release the system from the rack by lifting the slam latches and sliding the system out of the rack.
NOTE: If applicable, use a Phillips #2 screwdriver to unscrew the captive screws that secure the system to the rack
- Slam Latch (2)
Securing rails to the rack
To secure the rails to the rack for shipping or in unstable environments,
install the supplied screws to the rails.
NOTE: For square hole racks, install the supplied conical washer to the
screw before installing the screw.
NOTE: For unthreaded round-hole racks, install only the screw without the
conical washer.
-
Align the screws with the designated U spaces on the front and rear rack flanges.
NOTE: Ensure that the screw holes on the tab of the system retention bracket are seated on the designated spaces. -
Insert and tighten the two screws using the Phillips #2 screwdriver to secure the rails to the rack.
Routing the cables
NOTE: To install the Cable Management Arm (CMA), refer to the document shipped with your CMA.
If you did not order the CMA, use the two straps provided in the rail kit to route and secure the cables at the back.
-
Locate the CMA bracket slots on the rear end of both rails.
-
Bundle the cables gently, pulling them clear of the system connectors to the left and right sides.
NOTE: Ensure that there is enough space for the cables to move when you slide the system out of the rack. -
Thread the straps through the CMA bracket slots on each side of the system to hold the cable bundles.
CMA bracket slot
- P/N RM2HW Rev. A00
- © 2017 Dell Inc. or its subsidiaries.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>