ASTRALPOOL 70870 Lumiplus Essential Projector Instruction Manual

LUMIPLUS ESSENTIAL PROJECTOR
INSTALLATION AND MAINTENANCE MANUAL

IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before beginning installation and start-up. Keep this manual for future reference.
To achieve optimum performance of the Lummi Plus Essential Projectors follow the instructions provided below:

VERIFY THE CONTENTS OF THE PACKING

The following accessories are included inside the box:

PROJECTOR:
70870, 75434, 75776, 75435, 75777, 75778| CONCRETE POOL PROJECTOR:
66828, 74558, 75780, 75437, 75781, 75782| PREFABRICATED POOL PROJECTOR:
70528, 75439, 75783, 75440, 75784, 75785
---|---|---
Projector unit| Projector unit| Projector unit
Lamp| Lamp| Lamp
| Housing body| Housing body
| Watertight joint
Clamp
Bag of screws:
2 DIN 7981 4,8×16 screws
16 DIN 966 M-6×24 screws (1)
16 DIN 7982 5,5×25 screws (2)
(1) For projectors with metric pitch housing
(2) For projectors with self-threading housing

GENERAL CHARACTERISTICS

This projector has been designed to be used fully submerged underwater in fresh water swimming pools. It is a Class III electric apparatus with very low safety voltage (12V with alternating current).
The projector compiles with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a nominal immersion depth of 2 m.
This projector compiles with international safety standards for lights, especially the EN 60598-2-18 standard. LIGHTS PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components which have been inserted or handled at locations other than its own premises.

INSTALLATION

• Never install in vertical position with the lamp facing downwards.
• In order to clearly light a pool it is recommended lo install a projector every 25 or 35 m² of water surface.
• In order to prevent glare, the projectors should be installed so that they face away from the residence or usual view of the swimming pool.
• In the event that lighting is used in training or competition pools, the projectors should be installed on the sides to prevent glare on the swimmers.
• To avoid the need to empty the pool to change the lamp, we recommend that the projector be installed in areas which are accessible from the upper edge of the pool.

Prior to installation verify that the gland seal (nº 8) has been fully tightened.
The projector should be placed on the wall of the pool at approximately 400-700 mm from the water surface (Fig.1).
The method of fastening the housing to the pool wall varies depending on whether it is a projector for concrete pools or prefabricated pools.
Concrete swimming pool
To install a projector in a concrete swimming pool the housing (nº 10) should be fixed in the wall of the swimming pool (Fig. 2). Make sure that the cable outlet of the housing remains on the upper part.
Prefabricated swimming pool
To install a projector in prefabricated swimming pool make a circular hole with a diameter of 240 mm (Fig. 2).
Install the housing (nº 10) on the outer side of the pool (The housing incorporates the joint that carries out the water tightness). Install the adhesive joint on the inner side and use two screws DIN 7981 4,8×16 (nº 12) to secure the two components (Fig. 3). Make sure that the cable outlet of the housing remains on the upper part.
To install the clamp (nº 13) on the inner side of the swimming pool, make sure that the heads of the screws DIN 7981 4,8×16, which have been installed previously (nº 12), coincide with the area reserved for them on the back part of the clamp.
Secure the clamp (nº 13) to the pool wall using 16 screws:
DIN 966 M-6 x 24 point if the housing is for screws with metric pitch (Fig. 4).
DIN 7982 5,5 x 25 if the housing is for self-threading screws (Fig. 4).

ASSEMBLY

After installation of the housing and the clamp, if it is a prefabricated swimming pool, assemble the projector. To connect the projector to the electric power supply insert the cable through the gland seal nut (nº 5). Tighten the gland seal nut until you can verify that the cable will not yield when you pull on it with your hand.
Take the precaution of leaving 1.5 m of cable wound on the base of the projector (nº 11) in order to be able to remove the projector to the edge of the pool in the event that lamp replacement or handling is required (Fig. 5).
Insert the entire projector assembly in the housing (Fig. 6). In order to obtain good pool lighting it is important that the anagram of the decorative ring (nº 1) is located on the upper part (Fig. 7).
Screw in the two M-6 x 80 screws (nº 7) until the fastening dog is secured in the inner walls of the housing (Fig.8).

MAINTENANCE

To remove the projector to the edge of the swimming pool (Fig. 5) loosen the two DIN 966 M-6 x 80 screws (nº 7) until the fastening dog yields sufficiently so that the projector unit can be separated from the housing.
To remove the lamp, unscrew the 6 nuts (nº 2) which secure the decorative ring (nº 1) to the base of the projector (nº 5) (Fig. 9).
Remove the lamp (nº 9) from the inside of the base of the projector and disconnect the two terminals, loosening the two screws which secure them to the lamp (Fig. 10),
Change the lamp and assemble the Projector, in the opposite order described in point 4 of assembly, taking special care to:

• Connect the cable terminals to the lamp, using the 2 screws supplied with the lamp (Fig. 11).
• Fully centre the 110×11 O-ring (nº 4) in its seat.
• Firmly tighten the nuts.

Attention:

• Before any handling ensure that there is NO voltage supplied to the projector.
• We recommend fitting Astral Pool’s Lummi Plus Essential lamps.
• In order to ensure full weathertightness, clean the seat of the O-ring (nº 4) for the lamp or replace the O-ring if you observe any notches or permanent damage.

START-UP

Ensure that the voltage the lamp receives is never greater than 12 V.
The projector should only operate underwater while secured to the vertical walls of the pool. Never switch on the projector if it is not underwater.

SAFETY WARNINGS

• The persons who are in charge of assembly should have the required qualifications for this type of work.
• If the end cable of this light fitting is damaged, it should only be replaced by the manufacturer, its technical service or by a similarly qualified person, to avoid any danger.
• Avoid making contact with the electric voltage.
• Comply with the current standards regarding accident prevention.
• In this regard, the IEC 364-7-702 standards must be observed. WIRING IN BUILDINGS. SPECIAL WIRING. SWIMMING POOLS.
• Any operation related to the maintenance or replacement of parts should be performed with the projector disconnected from the electric power system.
• Do not handle with wet feet.
• The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components which have been inserted or handled at locations other than its own premises.

CONCRETE POOL
66828; 74558; 75780 75437; 75781; 75782

PREFABRICATED POOL
70528; 75439; 75783 ,75440; 75784; 75785

TECHNICAL CHARACTERISTICS

TO BE USED ONLY WITH A SECURITY TRANSFORMER
THE UNDERWATER LIGHT NEVER TO BE SWITCHED ON IF IT IS NOT SUBMERGED
LAMP FOR SPECIAL USE PROJECTORS

Made in Spain
Scopa, S.A.U.
Fluidram S.A.-Astral pool
www.astralpool.com
Made by NIF A-17092610
75434E201
©2022 Fluidram S.A. All rights reserved. This document is subject to changes without prior warning.

References

• Español

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>