CALIBER CA 100.2M Amplifier Marin 2 Channel 800 Watt User Manual
- June 13, 2024
- CALIBER
Table of Contents
CALIBER CA 100.2M Amplifier Marin 2 Channel 800 Watt
SPECIFICATIONS, CONNECTIONS AND BUTTONS
Max. power output at 14.4V:| 2x 250W/4O
2x400W/2O
1x B00W/4O (bridged)
---|---
RMS output at 14.4V:| 2x 100W/4O
2x 160W/2O
1x 320W/4Q (bridged)
Frequency response| 20Hz-20kHz
Input Sensitivity RCA input| 0,25- 6V
Low/high pass filter| 40 – 400Hz
Total Harmonic Distortion| <1%
Signal to noise ratio (A-Weighted)| >90dB
Output Impedance| 2 -16 Ω
Power protection| Thermal-, Overload- and Short-circuit protection
Dimensions:| 188(W) x 107(D) x 40.2(H) mm
Description
- Crossover select
- Input Sensitivity RCA input
- Variable low/high pass filter frequency
- LED indicator power protection
Features
- Class-D amplifier.
- Stereo output.
- Bridgeable outputs.
- Variable input sensitivity: RCA input 0.25V to 6V.
- RCA output.
- Thermal-, Overload- and Short-circuit protection.
- Excellent muting circuitry assures no turn on/off ‘pops’.
- Built-in High/ Low Pass Filter
- European design and engineering.
- IPx6 waterproof standard rating.
- It will not fail or allow water seepage when exposed to heavy splashing or rain.
- UV and salt resistant
Mounting
The amplifier has to have at least 5 cm (2″) ventilation space at all sides, to allow the heat to rise away from the amplifier. To avoid the risk of malfunction, make sure that power and signal cables are connected securely to the amplifier cables. Don’t place the power- and signal cables together to reduce any noises and make sure that connections are placed so they can’t get wet.
The amplifier is rated IPX6, but we highly recommend to place the amplifier so
that it is protected from exposure to large amounts of water or rain and
direct sunlight.
Always make sure the amplifier is securely mounted on a flat surface and
doesn’t come loose due to vibration.
Installation
Remember to always disconnect battery ground before working on a
boat/vehicle’s electrical system!
Always place a fuse (20A) or circuit breaker no more than 30 cm (12″) from the
battery, for optimal protection.
Getting your power started
-
First, the +12V terminal is connected directly to the battery of your boat/vehicle.
Use a cable of at least 10 mm2, and make sure that the connectors are of the same value.
– Don’t forget the “Vehicle protection” fuse (20A).
– The +12V terminal should NOT be connected to the fuse box of the boat/vehicle. -
Second, the ground terminal (GND) must be fastened securely to the negative pole of the battery with the same mm2 cable as the positive cable (the same amount of power has to run through it). In case of a boat; do never connect it to the chassis.
-
Third, the last cable to connect is your remote turn-on (REM). Many head units have an output terminal for connection of the REM of an amplifier. If you don’t have such an output, a separate switch must be installed to control your amplifiers on/off function.
Signal Input
- Connect the RCA-outputs of your head unit to the RCA input terminals of the amplifier. Take good care that you connect the Right output of your head unit to a Righi input of your amplifier, and that you connect the Left output of your head unit to a Left input of your amplifier. Make sure that the connectors are placed so they can’t get wet.
- The Caliber Marine amplifiers feature a built-in variable crossover which allows you to fine-tune your amplifiers response as you like ii. Either for the Full Range sound, in which case the HPF-FLAT-LPF switch remains in its FLAT position, or you can specifically select the High-Pass-Filter (HPF) or Low-Pass-Filter (LPF) to adjust to your speakers requirements. The built-in variable crossover can be adjusted in a range from 40Hz – 400Hz.
Amplifier adjustments
- Put the input level adjustment knob to the minimum.
- Put the volume of your radio to 3/4 of the maximum.
- Now adjust the input level of the front channel. Slowly turn up the input level and listen carefully until you hear the amplifier begin to distort. A Caliber Amplifier “clips” very softly, so this can sometimes be a difficult adjustment.
Caliber Warranty
Due to the complexity of our products, we strongly recommend that this amplifier is installed by your authorized Caliber dealer. If properly installed by your dealer we provide a warranty for 12 months from the date of purchase
Precautions
Points to observe for safe usage
Read this manual carefully before using this item and its components.
They contain instructions on how to use this product in a safe and effective
manner. Caliber Europe BV cannot be responsible for problems resulting from
failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.
Failure to do so may cause personal injury or damage to the product.
Return it to your authorized Caliber Europe BV dealer for repairing.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more severe
stains, please dampen the cloth with water only. Anything else has the chance
of dissolving the paint or damaging the plastic.
Temperature.
Ensure that the ambient temperature is between 0°C and +45°C before turning on
the device.
Maintenance.
If you have problems, do not attempt to repair the unit yourself.
Return it to your Caliber Europe BV dealer for servicing.
Placement.
Place the product on a flat surface. Provide enough space
around the product for sufficient ventilation.
Heat.
Do not locate the appliance in the vicinity of a heat surface or
in direct sunlight.
Accessories.
Use only supplied accessories.
Caliber hereby declares that the item CA 100.2M is in compliance with the essential requirements and other relevant provisions of Directive 2014/30/EU (EMC) and 2011/65/EU (RoHS).
WWW.CALIBER.NL
CALIBER EUROPE BV · Kortakker 10 • 4264 AE Veen • The Netherlands
Documents / Resources
|
CALIBER CA 100.2M Amplifier Marin 2 Channel 800
Watt
[pdf] User Manual
CA 100.2M Amplifier Marin 2 Channel 800 Watt, CA 100.2M, Amplifier Marin 2
Channel 800 Watt, Marin 2 Channel 800 Watt, 2 Channel 800 Watt, 800 Watt
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>