ProMariner 53505 ProTournament Tournament Winning On Board Marine Battery Charger Owner’s Manual

ProMariner 53505 ProTournament Tournament Winning On Board Marine Battery

Charger

Product Information

The ProMariner ProTournamentelite Series is a professional-grade on-board marine battery charger designed for tournament-winning performance. It is IP67 waterproof and suitable for use with Flooded (Lead Acid), AGM, HP AGM, or LiFePO4 batteries. The charger comes with a 5-year warranty and is pre-wired for easy installation.

Specifications:

• Model: ProTournamentelite Series
• Available Models: ProTournament240 (2-4 bank), ProTournament360 (3-4 bank), ProTournament500 (5 bank), ProTournamentG360 (3-4 bank), ProTournamentG500 (5 bank)
• Voltage: 12/24/36/48 volts (depending on model)
• Amps: 2-5 amps (depending on model)
• Cable Length: 6′
• Dimensions (H x W x D): Vary depending on the model
• Weight: Varies depending on the model

Important Notice:
Please save and read all safety, operating, and installation instructions before installing or applying AC power to your ProMariner ProTournamentelite On-Board Marine Battery Charger.

Warranty Information:
If you require any warranty, service, or installation assistance, please contact the ProMariner Customer Care Department at 800-824-0524 from 8:30 am to 5 pm Eastern Time.

Product Usage Instructions

Charger Operation Note:
Once your new ProTournamentelite is installed and properly connected to batteries, follow the steps below:

1. Plug in the charger to an AC outlet.
2. The charger will automatically perform a self-test and analyze all battery connections.
3. The self-test takes approximately 1 minute to complete.
4. During the self-test, the analyze mode LED will pulse.
5. If everything is connected properly and the batteries are above 2.5 volts DC, the charger will register and illuminate the green system check indicator followed by a solid (non-flashing) red charge mode LED indicating that all batteries are charging.

For further information on product usage, please refer to the following sections in the user manual:

• Introduction
• Important Safety Instructions
• General Overview
• General Operation
• Approved Lithium Batteries
• CZone
• Installation
• Typical Wiring
• Charging your Batteries
• Maintenance
• Troubleshooting
• Warranty Information

Visit ProMariner online at www.promariner.com, for a complete selection of quality marine products.

Here are just a few:

• ProMar1DS Series – Recreational Grade Waterproof Marine Battery Chargers
• ProSportHD Series – Heavy Duty Recreational Grade Marine Battery Chargers
• ProTechOne – On-Board Battery Charger & Maintainer
• ProNautic P Series – Sailing and Cruising Marine Battery Chargers
• ProIsoCharge Series – Digitally Controlled Zero Loss Charging Isolators
• Digital Mobile Charge In-Transit Chargers
• ProSport 1.5 Amp Multi-Use Maintainer
• Universal AC Plug Holders
• Battery Isolators
• Galvanic Isolators
• Online Technical Support and Service Support

Owner’s Manual and Installation Guide

Part No.| Model| Volts| Total Amps| No. Bat| Cable Length| Size (H x W x D)| Weight| AC In/Max Amps
---|---|---|---|---|---|---|---|---
53242| ProTournament 240 Two Bank| 12/24| 24| 2| 6′| 7.1″ x 3.2″ x 13.4″| 9.0 lbs| 120±10% VAC / 7.5 A
53243| ProTournament240 Three Bank| 12/24/36| 24| 3| 6′| 7.1″ x 3.2″ x 13.4″| 9.5 lbs| 120±10% VAC / 7.5 A
53244| ProTournament 240 Four Bank| 12/24/36/48| 24| 4| 6′| 7.1″ x 3.2″ x 13.4″| 9.9 lbs| 120±10% VAC / 7.5 A
53363| ProTournament360 Three Bank| 12/24/36| 36| 3| 6′| 9.3″ x 4.2″ x 13.7″| 15.4 lbs| 120±10% VAC / 10 A
53364| ProTournament360 Four Bank| 12/24/36/48| 36| 4| 6′| 9.3″ x 4.2″ x 13.7″| 15.8 lbs| 120±10% VAC / 10 A
53505| ProTournament500 Five Bank| 12/24/36/48 + Eng| 50| 5| 6′| 9.3″ x 4.2″ x 14.7″| 16.9 lbs| 120±10% VAC / 13 A
55363| ProTournamentG360 Three Bank| 12/24/36| 36| 3| 6′| 9.3″ x 4.2″ x 14.7″| 16.1 lbs| 100-240 VAC / 8 A
55364| ProTournamentG360 Four Bank| 12/24/36/48| 36| 4| 6′| 9.3″ x 4.2″ x 14.7″| 16.8 lbs| 100-240 VAC / 8 A
55505| ProTournamentG500 Five Bank| 12/24/36/48 + Eng| 50| 5| 6′| 9.3″ x 4.2″ x 16.6″| 18.0 lbs| 100-240 VAC / 10 A

IMPORTANT NOTICE
Please save and read all safety, operating, and installation instructions before installing or applying AC power to your ProMariner ProTournamentelite On-Board Marine Battery Charger.

Your Satisfaction is Important to Us!
Do not return this product to the retailer or dealer for any service or warranty requirements. Please call our Customer Care Department at 800-824-0524 from 8:30 am to 5 pm Eastern Time for any warranty, service, or installation assistance. Thank you – ProMariner Customer Care

For use with Flooded, AGM, HP AGM, and LiFeP04 Batteries. Not for use with Gel batteries, 4D or 8D large capacity batteries.

• Model Number:
• Serial Number:
• Date of Purchase:

Important Charger Operation Note:

• Once your new ProTournamentelite is installed and properly connected to batteries you will be ready to plug it in.
• Please note the ProTournamentelite has a built-in self-test feature that will also analyze all battery connections and batteries to determine if your boat’s batteries are capable of being charged correctly. The self-test is automatic and will take place every time the unit is plugged into an AC outlet. The self-test takes approximately 1 minute to complete.
• During the self-test, the analyze mode LED indicated will pulse. When completed if everything is connected properly and the batteries are above 2.5 volts DC then the charger will register and illuminate the green system check indicator followed by a solid (non-flashing) red charge mode LED indicating all batteries are charging.
• If the charger does not go into the charge mode with a solid red charge mode indicator and the System Check indicator is not illuminated with a solid green LED then a red battery bank fault LED will illuminate identifying the battery(s) that have either a wiring fault present i.e. poor connection, a blown DC cable fuse, the DC cable is wired in reverse polarity, battery cable is wired across multiple batteries in series, or the battery itself may be under 2.5 volts DC. In any of these cases, refer to the troubleshooting section on page 32 of this manual.

Introduction

Thank you from all of us at ProMariner and congratulations on your recent purchase of the new ProTournamentelite Generation 3 On-Board Marine Battery Charger. ProTournamentelite3 provides a competitive edge getting you on the water first with power to last. Using advanced thermal modeling, its tri- surface aluminum heat sink delivers true-rated constant current charging amperage for the fastest charge times.

Packed with new features, the ProTournamentelite3 boasts an industry-first LED Charge Status AC Glow Plug, that when connected to an extension cord outside of your boat, illuminates 3 individual colors for charging, conditioning, or auto-maintaining your fully charged batteries. High Power ProTournamentelite 360 and 500 models feature an industry-leading selectable TurboCharge Mode with Forced Induction Power Flow Cooling* for time-critical charging.
Give your batteries what they demand with ProTournamentelite’s four digitally selectable performance-matched 5-stage charge profiles now including ProMariner-approved LiFeP04** batteries as well as pure lead AGM and flooded lead acid batteries.

Have the edge with our elite Professional Performance feature set:

• Charge Status AC Glow Plug*
• TurboCharge Technology and Power Flow Cooling* (360 and 500 Models)
• Fastest Charge Times with Distributed-On-Demand™ Technology
• Full Output 5-Stage Digital Performance Charging
• Digital LED Display with Dual Function Battery Status Monitor
• System Check OK and Check Battery Indicators
• Auto Maintain/Energy Saver Mode
• Tri-Surface Heat Sink Design
• Waterproof Connector Port For Optional Remote
• Global AC Input with CZONE NMEA2000® system models available (360G and 500G models only)

Have 4 or 5 batteries to charge at one time on board?
Try our New! 50 Amp 5 Bank and 24 Amp 4 Bank Models. Designed to last in harsh environments and certified to UL Marine 1236 while meeting new energy- efficient CEC and DOE requirements. Built-in safety features include dual inline waterproof fuses, reverse polarity, over-temperature, over-current, over-voltage, and ignition protection.

For more information on the ProTournamentelite3 Series, scan and visit us at:

• Patent Pending
• See manual or promariner.com/Li for approved LiFePO4 batteries and warnings

Specifications are subject to change.

Important Safety Instructions

SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for the ProTournamentelite On-Board Marine Battery Charger.

CAUTION

• To reduce the risk of injury, charge only Lead-acid or LiFeP04-type rechargeable batteries; Flooded, AGM, HP AGM, and LiFeP04. Other types of batteries may burst, causing personal injury.
• Use of attachments not recommended or sold by ProMariner may result in a risk of fire, electrical shock or personal injury.
• EXTERNAL CONNECTIONS TO CHARGER SHALL COMPLY WITH THE UNITED STATES COAST GUARD ELECTRICAL REGULATIONS (33CFR183, SUBPART 1).
• Before connecting your batteries or applying AC power, read all instructions and cautionary markings on the battery charger, cables, and batteries.

WARNING
To reduce the risk of injury to the user or property; the user must read and understand the instruction manual and all warnings on the charger and batteries before use.

WARNING
RISK OF EXPLOSIVE GAS MIXTURE. Read the instructions in the manual before using the charger.

1. Connect and disconnect battery leads only when the supply cord is disconnected.
2. Do not overcharge battery – See Instruction Manual.
3. Do not smoke, strike a match, or cause a spark in the vicinity of the battery.
4. Use in a well-ventilated area.
5. Refer to the Instruction Manual for further details.

CAUTION

• Risk of Electric Shock. Connect only to properly grounded GFCI (ground fault circuit interrupt) protected outlets.
• Do not expose AC Power cord connection to rain or snow.
• If cords or wires/cables become damaged, return the complete unit to ProMariner for service/repair immediately.

WARNING

1. WARNING – RISK OF EXPLOSIVE GASES.

   • WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
   • To reduce the risk of battery explosion, follow these instructions and those marked on the battery.

2. Use a charger for charging a LEAD-ACID or LiFeP04 battery only. It is not intended to supply power to an extra-low-voltage electrical system or to charge dry-cell batteries. Charging dry-cell batteries may burst and cause injury to persons and property.

3. NEVER smoke, strike a match, or cause a spark or flame in the vicinity of the battery.

4. NEVER charge a frozen, damaged, or leaking battery.

5. Study all battery manufacturer’s specific precautions such as removing or not removing cell caps while charging and recommended rates of charge.

6. Use of an attachment not recommended or sold by ProMariner may result in a risk of fire, electric shock, or injury to persons.

7. To reduce the risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger.

8. Extension cords should not be used unless absolutely necessary. Use of an improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used make sure:

   • Pins on the plug of the extension cord are the same number, size, and shape as those on the plug of the charger.
   • Use only a properly wired extension cord in good electrical condition.
   • Use an industrial grade/heavy duty UL or CSA-approved and grounded extension cord. Check the extension cord before use for damage, bent prongs, and cuts. Replace if damaged. Always make your extension cord connection on the charger side first. After connecting the extension cord to the charger proceed to plug the extension cord into a nearby GFCI-protected (Ground Fault Circuit Interrupt) outlet. Below are manufacturer recommendations for the right size UL or CSA-approved grounded extension cord.
   • Up to 50 feet in length use a 3 conductor 14 AWG extension cord.
   • 50 to 100 feet in length use a 3 conductor 12 AWG extension cord.
   • 100 to 150 feet in length use a 3 conductor 10 AWG extension cord.

9. Do not operate the charger if any protective AC and DC cable insulation, charging clamps, DC fuse holders, and/or maintainer ring terminals have been damaged or compromised. Return the charger for service and repair to ProMariner immediately.

10. Do not operate the charger if it has received a sharp blow, direct hit of force, been dropped, or otherwise damaged in any way. Return the charger for service and repair to ProMariner immediately.

11. Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock or fire. If service or repair is required please call ProMariner customer service at 800-824-0524 between 8:30 am-5 pm (EST) Monday through Friday, or via www.promariner.com. Unauthorized attempts to service, repair, or modify may result in a risk of electrical shock, fire, or explosion and will void the warranty.

12. To reduce the risk of electric shock, unplug the charger from the outlet before attempting any maintenance or cleaning.

13. Do not expose the AC power cord connection to rain or snow.

14. GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS

    • The charger should be grounded to reduce the risk of electric shock. The charger is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a GFCI-protected (Ground Fault Circuit Interrupt) outlet that is properly installed and grounded in accordance with all local codes and ordinances.
      DANGER
      Never alter the AC cord or plug provided – If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection can result in a risk of an electric shock.

    • This battery charger is for use on a nominal 120-volt circuit and has a grounding plug that looks like the plug illustrated in Figure A. A temporary adapter, which looks like the adapter illustrated in Figure B may be used to connect this plug to a two-pole receptacle as shown in Figure B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded GFCI-protected outlet can be installed by a qualified electrician.
      DANGER
      Before using the adapter as illustrated, be certain that the center screw of the outlet plate is grounded. The green-colored rigid ear or leg extending from the adapter must be connected to a properly grounded outlet – make certain it is grounded. If necessary, replace the original outlet cover plate screw with a longer screw that will secure the adapter ear or lug to the outlet cover plate and make a ground connection to the grounded GFCI-protected outlet.
      The use of an adapter is not allowed in Canada. If a grounding-type receptacle is not available, do not use this appliance until the proper GFCI-protected outlet is installed by a qualified electrician.

• PERSONAL PRECAUTIONS
  CAUTION

  • Consider having someone close enough or within the range of your voice to come to your aid when you work near a lead-acid battery.
  • Have plenty of soap, water, and baking soda nearby in case battery acid comes in contact with skin, clothes, or eyes.
  • Wear complete eye protection, and hand and clothing protection. Avoid touching your eyes while working near a battery.
  • If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters the eye, immediately flood the eye with running cold water for at least 15 minutes and get medical attention immediately.
  • NEVER smoke, strike a match, or cause a spark or flame in the vicinity of the battery or engine.
  • Be extra cautious to reduce the risk of dropping a metal tool onto the battery. It might spark or short-circuit a battery or other electrical hardware which may cause an explosion or fire.
  • Remove all personal metal items such as rings, bracelets, necklaces, watches, and jewelry when working near a battery. A battery can produce a short circuit current high enough to weld a ring or any other metal, causing serious burns.
  • Use a charger for charging a LEAD-ACID or LiFeP04 battery only. It is not intended to supply power to a low-voltage electrical system other than in a start-motor application. Do not use a battery charger for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause injury to persons and damage to property.
  • NEVER charge a frozen, damaged, or leaking battery.
  • Keep other persons, children, and pets away from batteries and your charger during operation to avoid serious injury, death, fire or explosion.
    DANGER: RISK OF ELECTRIC SHOCK
    Do not touch the uninsulated portion of the output connector or uninsulated battery terminal if 3 or more batteries are connected in series.

• PREPARING TO CHARGE A BATTERY
  CAUTION

  • If necessary to remove a battery from a boat to charge, always remove the grounded negative terminal from the battery first. Make sure all accessories in the boat are off, so as to not cause an arc. Be sure the area around the charger and batteries is well-ventilated while the batteries are being charged. Gases can be forcefully blown away using a piece of cardboard or other nonmetallic material as a fan.
  • Be sure the area around the charger and batteries is well-ventilated while the battery is being charged.
  1. If the electrolyte is splashed into an eye, immediately force the eye open and flood it with clean, cool water for at least 15 minutes. Get prompt medical attention.
  2. If electrolyte is taken internally, drink large quantities of water or milk. DO NOT induce vomiting. Get prompt medical attention.
  • Neutralize with baking soda any electrolyte that spills on a vehicle or in the work area. After neutralizing, rinse the contaminated area clean with water.
  • Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.
  • For flooded batteries with removable caps, ONLY ADD DISTILLED WATER in each cell until the electrolyte reaches levels specified by the battery manufacturer. Do not overfill. For a maintenance-free battery without removable caps, such as valve-regulated lead acid batteries, carefully follow the manufacturer’s recharging instructions.
  • Study all battery manufacturers’ specific precautions; warnings and instructions while charging and recommended rates of charge. Never charge a battery with missing safety vent caps.
  • Do not overcharge batteries by selecting the wrong battery type or by trying to charge a non-12 Volt battery as defined by the 12 Volt battery types specified in this manual.
    Always remove the extension cord from the outlet first when charging is completed followed by unplugging the charger, and completely disconnecting.

• CHARGER LOCATION
  CAUTION

  • Locate the charger as far away from the batteries as possible.
  • Never place a charger directly above a battery being charged; gases or fluids from the battery will corrode and damage the charger.
  • Do not operate the charger in an enclosed area or in an area with restricted ventilation in any way.
  • Never allow battery acid to drip on the charger when reading electrolyte-specific gravity or filling a battery.
  • Do not set a battery on top of the charger.
  • Do not install on or over combustible surfaces.

• DC CONNECTION PRECAUTIONS
  CAUTION

  • Connect and disconnect DC output cables only after removing the AC cord from the electric outlet. Never allow cables to touch each other.

IMPORTANT NOTICE: FCC CLASS B PART 15 NOTIFICATION
Your On-Board Marine Battery Charger has been designed and tested to comply with FCC Class B part 15. These regulations are to provide adequate protection against harmful interference while operating in a commercial application. If in a residential setting, you are encountering interference with TV and radio reception, simply remove AC power from the ProMariner unit to confirm if your battery charger is causing interference. The end user can explore the following to minimize interference:

1. Choose a different AC circuit to power your On-Board Marine Battery Charger.
2. Make sure your outlet is properly grounded.
3. Re-position the receiving antenna.
4. Purchase a separate AC line filter.
5. Relocate the charger so that it is at the furthest point from the home receiving equipment, TV, radio, etc.

General Overview

ProTournamentelite Generation 3 is our most advanced, fully automatic, digitally controlled, multi-stage on-board marine battery charger. ProTournamentelite is pre-wired for easy installation and is 100% waterproof for fresh and saltwater applications. ProTournamentelite’s multi-stage performance charging process delivers five modes of operation that include: start up diagnostics, charging, conditioning, auto maintenance and storage auto reconditioning of each battery. This process is proven to extend the life of your batteries and will fully charge your batteries each time you connect to AC power. ProTournamentelite delivers the fastest charge time with time- saving features like TurboCharge and Power Flow Cooling* which allows maximum charging performance with forced induction air cooling.

The ProTournamentelite’s Distributed-On-Demand™ Technology will automatically sense and distribute 100% of the available charging output (up to 18 amps per battery) in proportion to the discharge state of each battery connected.
ProTournamentelite’s easy to view Charge Status AC Glow Plug* provides at a glance status of: charging, conditioning and auto maintaining fully charged batteries without having to get in the boat to see.
Included on the front of ProTournamentelite is a dual function battery status monitor, System Check OK and Check Battery indicators providing: individual battery charge level monitor with an on-the-water push-to-test feature for percent of battery power remaining. Eliminate time consuming trouble shooting by indicating system OK or specific batteries requiring attention.

Battery profile selection and charge mode LEDs are also captured on the front user interface in an easy-to-view layout.

• Patent Pending

Note:
The ProTournamentelite must be connected to batteries to operate. It will not operate as a 12 volt power supply.

How Distributed-On-Demand™ Charging Technology Works

ProTournamentelite’s Distributed-On-Demand™ Charging technology ensures 100% of the available (up to 18 amps per battery) charging amps are fully utilized to meet the demand of each battery on-board. For example, if your engine start battery only needs 2 amps from your ProTournament240elite, the unused 6 amps will automatically be Distributed-On-Demand™ to your house or trolling motor batteries, providing 11 amps to each of your deep cycle batteries for faster charging.

**General Operation

**

Install your ProTournamentelite On-Board Marine Battery Charger to the guidelines in this manual. Do not alter the ProTournamentelite during the installation process. Extra equipment and cable extenders are available for purchase if required.

• The ProTournamentelite will automatically charge and condition your batteries. Always leave your charger plugged in to reduce sulfate build-up inside the battery; this extends your battery life by allowing the charger to automatically maintain and charge your batteries while you are away. Your batteries will always be ready for your next fishing trip!
• The ProTournamentelite design incorporates a Storage Recondition mode that stimulates and reconditions your on-board batteries for 3 hours once a month and when completed will resume its normal energy saver auto maintain mode.
• During this mode the Auto Maintain bar will illuminate green with a fade-in fade-out pulse, indicating Storage Recondition mode is active with the green Auto Maintain LED still illuminated indicating your batteries remain fully charged during this process.

ProTournamentelite LED Status Center – Operation & Display

ProTournamentelite includes various LEDs for operation status and up to 5 battery bank trouble LEDs depending on the model.

1. The Blue On LED
   Illuminates when AC power is applied

2. The Battery Type LED
   Will illuminate blue for Flooded/AGM, green for AGM 1, amber for AGM2, or red for LiFePO4.

3. The System Check LED
   After applying AC power the ProTournamentelite will self test and analyze all battery connections and batteries. If all checks are OK, the LED will illuminate green. This can take up to 1 minute. If the LED illuminates red, the system has detected an internal fault and shutdown.

4. The Charge Mode LEDs and Charge Status AC Glow Plug

   • Analyze: Blue LED pulses during the self test and battery test mode (approximately 1 minute). Note: AC Glow Plug is off in Analyze mode
   • Charging: Red LED illuminates while charging.
   • Conditioning: Amber LED illuminates while conditioning.
   • Auto Maintain: Green LED illuminates when the batteries are fully charged and automatically maintained until you are ready to use your boat.
   • Auto Storage Recondition: Green LED pulses when performing a once-a-month storage recondition mode.

5. Dual Function Battery Status Monitor

   • Mode 1 – Charge completion status
     During this mode, when the ProTournamentelite is connected to the AC power, the dual-function battery status monitor will automatically display the charge level for each battery during the charge process until all batteries are fully charged.

   • Mode 2 – Push-to-test charge status
     During this mode, use the push-to-test button when the ProTournamentelite is NOT connected to AC power to display the current charge level remaining.

6. Battery Bank Trouble Status LEDs
   Individual red LEDs will illuminate indicating a wiring problem or fault at each of the batteries connected to the ProTournamentelite charger. See page 32 for further details.

7. Check Fan LED (360 and 500 models)
   ProTournament360elite and ProTournament500elite models have a fan-powered cooling feature. If the fan becomes inoperable, the “Check Fan” LED indication will illuminate red. See page 32 for troubleshooting details.

Multi-Stage Charging Overview

• Stage 1 – System Check and Battery Analyzing: During this stage, the blue “Analyze” LED will pulse. This indicates that ProTournamentelite is performing a self-test, analyzing all battery connections, and checking if each battery is capable of being charged. Upon completion, the “System Check” LED will illuminate green followed by Stage 2.
  Note: While in analyze mode, the battery type can be changed by following the steps in the “Selecting a Charging Profile” section on page 12. The charger will not leave analyze mode if a fault is detected.

• Stage 2 – Charging: During this mode, the “Charging” indicator will be solid red. The ProTournamentelite Series will use all of its available charging amps (as controlled by temperature) until the battery voltage is raised to 14.4 VDC (Flooded/AGM factory setting).

• Stage 3 – Conditioning: During this mode the “Conditioning” indicator will be amber. Batteries will hold at 14.4 VDC (factory set for Flooded/AGM batteries) to complete charging while conditioning each battery connected. Upon completion, the ProTournamentelite will go into Auto Maintain mode.

• Stage 4 – Auto Maintain (Energy Saver Mode): During this mode the green “Auto Maintain” LEDs will be on indicating Stage 2 charging and Stage 3 conditioning are completed. At this time the ProTournamentelite will initiate its Auto Maintain (Energy Saver Mode) which will monitor and Auto Maintain batteries only when needed to maintain a full state of charge.

• Stage 5 – Auto Storage Recondition Mode: During this mode the green “Auto Recondition Mode” indicator will illuminate with a slow fade in and out pulse. This indicates that while your batteries/boat are in storage the ProTournamentelite will automatically recondition all batteries for up to 3 hours once a month extending battery life and maximizing the water battery power performance.

5 Stage Performance Charge Profile

Understanding Battery Types & Charger Settings
There are three primary types of batteries in the marketplace today; standard Flooded (Lead-Acid), AGM (Absorbed Glass Mat)/high-performance AGM, and Gel cell (Gelled Electrolyte Lead-Acid). Traditionally, the most common type of batteries used are Flooded (Lead-Acid) batteries. In addition to the 3 lead acid batteries, lithium batteries are becoming readily available as lead acid battery replacements. Almost all Gel cell batteries will state that they are Gel cell on the battery case or labels. Shown below are typical battery voltages at absorption and float levels.

For use with approved lithium batteries only. See page 12 or visit https://www.promariner.com/Li for a list of approved batteries.

Understanding Battery Types & Charger Settings Continued

NOTE:
AGM (Absorbed Glass Mat) batteries are not Gel (Gelled Electrolyte Lead-Acid) batteries. Gel batteries require a completely different charge profile that must be selected versus the out-of-the-box factory setting. AGM batteries can accept the same charging profile as Flooded (Lead-acid) batteries.

• Note: In LiFePO4 mode, the DC terminals are powered when AC is present.
• Note: If you are still unsure what kind of battery(s) you have, we recommend that you contact the manufacturer of the battery(s).

Selecting a Charging Profile
Your battery charger is equipped with a user-programmable battery type selector that is factory-set for standard Flooded (Lead-Acid) batteries.

• CAUTION: Connect the charger to the battery before applying AC Power.
• CAUTION: Remove AC power before disconnecting the charger from the battery.

To select a different battery profile, use the following steps:

1. Power on the charger.

2. Press and hold the select button for more than 2 seconds to enter battery type select.
   Note: You can only enter battery type selection in analyze mode (Pulsing blue “Analyze” LED)

3. Press and release the select button to cycle through battery types.

4. Press and hold the select button for more than 2 seconds to set the battery type.

Approved Lithium Batteries

Mastervolt MLI 1250
Tracker WRM60, WRM80, WRM100, TLi60, TLi80, TLi100 RELiON RB60, RB75, RB80, RB100, RB100-HP, RB100-LT Battle Born BB10012

To see a complete and up-to-date list of approved lithium batteries, please visit https://www.promariner.com/Li.

TurboCharge (360 and 500 models)

TurboCharge

Turbo Charge Mode
The ProTournamentelite comes with a TurboCharge button. To use this function, simply press the TurboCharge button once the unit is in charge mode and the fan will turn to full speed to keep the charger cool and maximize the current output.

CZone

CZone (Global models only)

Com ID Selection (For Global AC Input Models Only)
Your battery charger is equipped with a CZone/NMEA2000® communication interface. If you are using more than one ProTournamentelite to charge your system in the same CZone/NMEA2000® network, the Com ID must be set to be different for each ProTournamentelite charger. If you are using only one ProTournamentelite, you do not need to change the Com ID.

To set the Com ID, follow the 3 steps below:

1. Press and hold the com button for 3 seconds and release. The comm ID number and LED will be blinking indicating that the Com ID can be set.
2. Press the com button to change the selected Com ID. Repeat the button press until the desired Com ID is selected.
3. Press and hold the com button for 3 seconds to save the selected Com ID in the charger.

CZone Communication
The CZone interface communicates battery chemistry, charge mode, real-time charging voltage, amperage, and fault status. See examples below:

Note: The CZone interface reports the charger’s voltages and currents.

For a complete communication list, please visit www.promariner.com /ProTournament-Elite-3-Global See the CZone configuration tool manual for setup.

Installation

• All ProTournamentelite Battery Chargers are designed to be permanently mounted on-board and should be mounted with extruded fins placed horizontally.
• Always mount your ProTournamentelite in a compartment area that can be properly ventilated during use.
• Do NOT mix battery types on board. All batteries should be of the same age and in good operating condition.
• Do NOT make any electrical connections to the ProTournamentelite or batteries until the following steps are completed:

Easy-to-Follow Installation Steps:

1. 1. Select a mounting location that allows for free air ventilation with a minimum of 8 inches of clear unobstructed space around and in front of the battery charger. Open all battery and engine compartments and ventilate for at least 15 minutes before starting the installation of the charger. Confirm all battery cables can reach each of the batteries.
   Do not install charger on carpeted, upholstered, vinyl, or varnished areas. Be sure to place the ProTournamentelite in an accessible area where all indicators are viewable. Install this unit on a hard surface.
   Note: For installations requiring an extension of the DC battery charger cables, please call or visit your retailer or dealer to purchase ProMariner’s 5 foot or 15 foot battery charger DC cable extenders. Our innovative cable extenders are properly fused and do not require any cutting or stripping of wires. If you have any problems locating this accessory call ProMariner at 1-800-824-0524.

2. Using the ProTournamentelite or the enclosed paper template, mark the position of each mounting hole. Ensure the mounting screws will not puncture or protrude into a live well, a fuel or oil tank or the bottom of the boat.

3. Using a 1/8″ drill bit, drill pilot holes in the (4) marked locations as described in step 2. Apply a silicon sealer in each of the mounting locations to waterproof the screw holes.

4. Position the charger over the mounting holes and secure with a power screwdriver by installing 4 stainless steel #10 screws. (mounting screws included).
   For aluminum boat installation we recommend installing your ProTournamentelite Charger on a wood or fiberglass panel and not directly on the aluminum hull.
   1/8″ pilot hole w/ silicon sealer
   IMPORTANT NOTICE

   • Maintain an obstruction-free area of 6 inches around the product.
   • Prior to mounting, confirm mounting surface has adequate strength and thickness.
   • Check for electrical or fuel lines on or behind the surface.
   • Consult the boat manufacturer for suggested mounting location or procedure.

5. Prepare each battery in advance by cleaning each terminal post with a wire brush until a shiny surface is obtained.

6. Run cables free from sharp objects and hold each in place with cable ties. Coil excess cable, do not cut or shorten the length of the cables, as in-line fuses are located 4 inches from the end of each positive (red) cable. These fuses protect the charger and output cables in the event of a wiring short. We recommend the use of wire ties or cable clamps to provide strain relief for the cables and to reduce the risk of damage to the cables or connections.

7. Connect the DC output cables as illustrated on pages 17-29. Make sure the (black) wires are connected as illustrated to the negative side of the battery and the (red) wires are connected to the positive side of the battery.
   CAUTION: Connect the charger to the battery before applying AC Power.
   Important Note: Your ProTournamentelite charger will not operate properly if it is not correctly connected to your batteries. Reminder: Each DC jacketed bank cable must be connected to a 12V battery. If there are more charger outputs than batteries, then sets of leads can be doubled on the larger battery in your system. Example: A 3-bank ProTournamentelite should be connected to three 12V batteries, but can be connected to as few as two, provided all the charger leads are connected and the 2 banks are connected to the highest capacity battery. Select the applicable wiring illustration on pages 17-29.

8. Make sure all DC connections are correct, tight, and free from corrosion.

9. Locate the AC power cord in an open-air area of your boat at least 21 inches from the charger, batteries, and fuel fill lines.

10. Connect a heavy-duty UL-approved extension cord to the battery charger first. After connecting the extension cord to the charger, proceed to plug the extension cord into a nearby GFCI-protected (Ground Fault Circuit Interrupt) outlet. Always remove the extension cord from the outlet first when charging is completed, followed by unplugging the charger. You are now connected and charging your batteries. View the LED indicators.

Wiring your ProTournamentelite Charger Correctly
Simply choose the illustration that has the same number of charger output bank cables as your ProTournamentelite Battery Charger in hand and wire exactly as shown (choose the illustration that best matches your application) for proper charger operation.

Incorrect wiring can result in reverse polarity, caused by putting the “red” + lead on a negative battery terminal and the “black” – lead on the positive terminal. In the event this happens, the ProTournamentelite Battery Charger has been designed to not fail as a result; however, it will cause the charger to “internally disconnect” and provide “no output” until the reverse polarity is corrected. In the event of a miswired battery(s), the charger will illuminate a red battery trouble status LED for the specific battery requiring attention.

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important: The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

WHEN CONNECTING TO AN ENGINE START BATTERY only connect the battery bank cable that is LABELED: “FOR ENGINE BATTERY USE THIS BANK CABLE ONLY”.

Application Tip
If your application is for 4D or 8D large capacity batteries, please refer to ProMariner’s website www.promariner.com and view our ProNauticP Hardwired Charger Assortment for a model that is correct for this group size of batteries.

If there are more charger outputs than batteries, then sets of leads can be doubled on the larger battery(s) in your system. Typically these are connected to the more drained trolling motor battery. Please contact ProMariner if you require assistance.

Note:

• Note: ProTournamentelite Waterproof Marine Battery Chargers are designed for any combination of group 24, 27, 29, 30 and 31 or equivalent batteries. Each DC output cable must be connected to one (1) 12 Volt DC battery (even if batteries are configured for 24, 36, or 48 VDC trolling motor or system applications). Most specifically you do not have to remove series or parallel jumper cables to use your ProTournamentelite Charger. See typical wiring diagrams for these systems in the installation section of this manual.
• Note: The ProTournamentelite must be connected to batteries to operate. It will not operate as a 12 volt power supply.

Typical Wiring

Fig. 1 ProTournamentelite Two Bank for 2 12V Batteries
Dedicated 24 VDC Trolling Motor Battery Configuration with (2) 12 VDC Batteries Connected with a Series Jumper

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 2 ProTournamentelite Two Bank for 2 12V Batteries
12 VDC Engine Start and a 12 VDC Trolling Motor or House Battery Configuration with (2) 12 VDC Batteries

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
  Black Wire = – (Negative) Battery connection
  The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 3 ProTournamentelite Two Bank for 2 12V Batteries in Parallel
Dedicated 12 VDC Parallel Trolling Motor or House Configuration

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important: The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 4 ProTournament240elite Three Bank for 3 12V Batteries
24 VDC Trolling Motor or House Battery Configuration with (2) 12 VDC Batteries Connected with a Series Jumper Plus Dedicated 12 VDC Engine Start Battery

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 5 ProTournamentelite Three Bank for 3 12V Batteries
Dedicated 36 VDC Trolling Motor Battery Configuration with (3) 12 VDC Batteries Connected with (2) Series Jumpers

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 6 ProTournamentelite Three Bank for 3 12V Batteries
Dedicated 12 VDC Trolling/House Bank and 2 Engine Crank Batteries Typical Configuration

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 7 ProTournamentelite Four Bank for 4 12V Batteries
36 VDC Trolling Motor Battery Configuration with (3) 12 VDC Batteries Connected with (2) Series Jumpers plus Dedicated 12 VDC Engine Start Battery

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 8 ProTournamentelite Four Bank for 4 12V Batteries
Dedicated 24 VDC Trolling/House Bank and 2 Engine Crank Batteries Typical Configuration

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 9 ProTournamentelite Four Bank for 4 12V Batteries
Dedicated 48 VDC Propulsion System Battery Configuration with (4) 12 VDC Batteries Connected with (3) Series Jumpers

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 10 ProTournamentelite Five Bank for 5 12V Batteries
Dedicated 12 VDC Batteries for House/Trolling Motors and Engines

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 11 ProTournamentelite Five Bank for 5 12V Batteries
Dedicated 24 VDC Trolling Motor Batter with Two 12VDC Engine Crank Batteries and One 12 VDC House Battery

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 12 ProTournamentelite Five Bank for 5 12V Batteries
Dedicated 36 VDC Trolling Motor Battery with 12VDC Engine Crank and House Battery

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Fig. 13 ProTournamentelite Five Bank for 5 12V Batteries
Dedicated 48 VDC Propulsion System Battery Configuration with One 12 VDC Engine Crank or House Battery

Installation
When connecting each jacketed battery charger cable, make sure it is connected to only one 12 VDC battery and observe the polarity and color of all connections:

• Red Wire = + (Positive) Battery connection
• Black Wire = – (Negative) Battery connection
• The black wire can never be connected to a terminal with red wires. Only black.

Important:
The pair of red and black wires in 1 cable jacket MUST GO TO THE SAME 12VDC battery.

• Note 1: One bank cable connects to no more than one battery
• Note 2: ProTournamentelite is designed to be used with group 24, 27, 29, 30 and 31 batteries

Charging your Batteries

The ProTournamentelite is designed to charge, condition, and auto maintain your batteries during short or long term periods of storage or non use. Please follow these steps each time you use your ProTournamentelite Battery Charger:

1. Read manual and all warnings.

2. Review “Preparing to Charge a Battery” on page 6.

3. Ensure charger is installed as per the installation instructions.

4. Connect a heavy duty UL approved extension cord to the ProTournamentelite Battery Charger first. After connecting the extension cord to the charger, proceed to plug the extension cord to a nearby GFCI protected outlet. Anytime power is applied to the ProTournamentelite the blue LED will illuminate.

5. The “Analyze” LED will pulse blue indicating the charger is in Analyze mode. While the charger is analyzing your batteries, check that you have the correct battery profile selected. This mode takes approximately 1 minute for the ProTournamentelite to do a self test, check all wiring connections, and make sure the batteries are greater than 2.5 Volts DC and are able to take a charge.
   Assuming there are no battery faults, the green “System Check OK” LED will illuminate and the following charger operation sequences will proceed:
   Note: If there is a bad connection, reverse polarity, or a battery that is below 2.5 VDC that can not accept a charge, then a RED Battery Trouble status LED will illuminate for the battery that requires attention. See page 32 for further troubleshooting details.

6. The “Charging” LED will be solid red indicating the charger has entered the Charging stage as outlined in the Multi-Stage Charging Overview section of this manual.
   CAUTION: HOT SURFACE. Avoid contact during charging operation as unit will be hot to the touch but operating safely and properly.

7. The “Conditioning” LED will be solid amber indicating that the ProTournamentelite will hold all batteries at the selected absorption voltage to complete charging by conditioning each battery for up to 3 hours as needed.

8. When the charge process is complete (or if your batteries are fully charged when you apply AC power) the “Auto Maintain” LED will be solid green indicating your batteries are fully charged and the charger is in auto maintain mode.

Optional ProTournamentelite Charge Status Remote
See your local dealer or retailer for the ProTournamentelite Charge Status Remote. The tri-color remote indicator is easy to install to the twist lock quick connector cable pre-wired on ProTournamentelite Chargers. The innovative design has an LED indication of charge status as well as an illuminated halo corresponding to the current charge mode (red for charge, amber for conditioning and green for ready).

Maintenance

Owner’s Periodic Maintenance Guide

Troubleshooting

No LEDs turn on when Plugged in.

1. Check for AC power
2. Check AC power quality by using a lamp or similar appliance to verify:
3. The GFCI has not tripped.
4. The extension cord is of good quality with good connections.
5. If AC power quality is verified with a lamp or similar appliance and LEDs do not illuminate, contact ProMariner.

System Check is Red
Your system has detected an internal problem and shutdown.

1. Contact ProMariner for assistance.

Red Fault LED is ON

1. Identify the bank LED that is on.
2. Check for the following on the corresponding bank for:
   • Clean and tight connections.
   • Blown fuses.
   1. Visually inspect fuses or test with multimeter.
   • Reverse Polarity.
   1. Verify that the red lead is connected to the positive terminal and the black lead is connected to the negative terminal.
   • Leads are across more than one 12 volt battery.
   1. Verify leads are connected to only one 12V battery.
   • Low battery voltage
   1. Verify the battery voltage is above 2.5 volts DC.
3. If none of the above situations are found and the Red Fault LED is still on, contact ProMariner.
4. Check Fan LED is ON after Self-test
   1. Disconnect the charger from AC Power.
   2. Clear the fan of any obstructions or blockages.
   3. If there is no obstruction, contact ProMariner.

Charger is in Auto-maintain & Red Fault LED is Pulsing
Your battery did not complete charging during a normal charge cycle.

1. Power off your charger
2. Allow batteries to rest for 1 hour
3. Power on your charger.
4. If the fault occurs again, have your battery tested.
5. If your battery is good, the charger may be undersized for your battery, contact ProMariner.

Contact ProMariner at 1-800-824-0524 from 8:30am to 5pm Eastern, by email at support@promariner.com, or visit us on the web at www.promariner.com.

Warranty Information

ProTournamentelite Marine Battery Charger Warranty
We are committed to customer satisfaction and value your business. If at any time during the warranty period you experience a problem with your new ProTournamentelite Marine Battery Charger, simply call us at 1-800-824-0524 between 8:30am-5pm (EST) Monday through Friday, for technical support or email info@promariner.com.

WARRANTY CARD CAN BE REGISTERED AT WWW.PROMARINER.COM or the warranty card included in this manual can be completed and sent to ProMariner by mail.

PROMARINER PROTOURNAMENT ELITE ON-BOARD MARINE BATTERY CHARGER LIMITED FIVE-YEAR FACTORY WARRANTY
Each ProTournamentelite Marine Battery Charger model is guaranteed against defects in material and workmanship to the original consumer in normal use for 5 years from the date of purchase. ProMariner will at its discretion repair or replace free of charge any defects in material or workmanship.

The following conditions apply:

• Warranty and repair adjustment calculated from manufacture date if not registered or proof of purchase within two weeks of sale.
• Warranty void if unauthorized repairs attempted
• Warranty void if any cables are cut or modified
• Deep water damage not covered under warranty
• Customer is responsible for shipping return unit to the ProMariner factory service center listed below.
• Cosmetic repairs are done at the owner’s request and expense.

Purchase or other acceptance of the product shall be on the condition and agreement that ProMariner SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. (Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.) This warranty is made in lieu of all other obligations or liabilities on the part of ProMariner. ProMariner neither assumes nor authorizes any person for any obligation or liability in connection with the sale of this product.

To make a claim under warranty, go to www.promariner.com and click on the resources tab and follow the instructions making sure to identify the product and the problem. If you can not use our online warranty claim registration, please feel free to call the ProMariner factory service center at the toll free number listed below. ProMariner will make its best effort to repair or replace the product, if found defective within the terms of the warranty, within 30 days after return of the product to the company. ProMariner will ship the repaired or replaced product back to the purchaser. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. This warranty is in lieu of all others expressed or implied.

ProMariner
Factory Service Center & Technical Support 15 Dartmouth Drive, STE 101 Auburn, NH 03032.

• USA TOLL FREE: 1-800-824-0524
• Tel: 603-433-4440
• Fax: 603-433-4442
• Email: support@promariner.com.
• Visit us on the web at: www.promariner.com.

References

• Approved Lithium batteries for use with the ProSport HD
• Home | ProMariner
• Approved Lithium batteries for use with the ProSport HD

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>