Havoc Offroad HFB-08-003 Interior Storage Rack Installation Guide
- June 13, 2024
- HAVOC OFFROAD
Table of Contents
Havoc Offroad HFB-08-003 Interior Storage Rack
Product Information
- Product Name: Interior Storage Rack
- Model: HFB-08-003
- Compatible Vehicle: Ford Bronco
- Revision: Rev. 0
- Date: 08/22
Components and Hardware:
- Interior Storage Rack
Note:
This rack allows you the option to securely mount a Farm Jack in the interior of your Bronco. The mount and basket have a cutout to accommodate the Farm Jack. This cutout must be towards the back of the rear seat. This will assist in determining which rack mount is for the driver’s or passenger’s side.
Tools for Installation:
- Hand Knob (3)
- Washer (4)
- Nut (5)
Product Usage Instructions
-
Step 1: Remove the plastic cover in the trunk area that covers the soft-top hinge mechanism. These covers are attached with clips. Simply pull on the cover to release the clips.
-
Step 2 (For Soft-Top ONLY): Remove the top two bolts holding the soft-top hinge mechanism. DO NOT remove the lower third bolt, as it will hold the mechanism in place while mounting the rack mount. Keep these bolts to be reused.
-
Step 3 (For Soft-Top ONLY): Place Rack Mount (2) into place. Reuse the OE bolts to loosely install this mount. Use the outer slots to mount for soft-top.
Use bolt (6), washer (7), rack mount (2), and spacer (8). Thread the bolt into the threaded inserts of the vehicle. Use the inner slots to mount for hard- top.
Note: Keep the cutout near the back of the rear seat. Refer to the note on page 1 for more information. -
Step 4 : With both driver and passenger rack mounts loosely installed, place rack (1) into position. It is recommended to have an assistant to help hold it in position while installing hardware.
Note: The Jack cutout must be towards the back of the rear seat. -
Step 5 : Use Button Head Bolt (9) with washer (10) through the rack and mount. Secure with Flange Nut (11). Requires three on each side. Adjust the basket and mounts to align and level, then fully tighten all hardware.
-
Step 6 : Replace the plastic covers removed from step 1. Press firmly to ensure all the clips engage.
Components and Hardware
- Storage Rack………………………………………………………………………. (1)
- Rack Mount (Driver & Passenger Side)………………………………….. (2)
- M8 x 1.25mm Hand Knob…………………………………………………….. (2)
- M8 Large Flat Washer………………………………………………………….. (2)
- M8 x 1.25mm Hex Nut…………………………………………………………. (2)
- M8 x 1.25mm, 50mm Serrated Flange Bolt……………………………. (4)
- M8 Large Flat Washer………………………………………………………….. (4)
- 22mm Spacer……………………………………………………………………… (4)
- M8 x 1.25mm, 20mm Button Head Bolt…………………………………. (6)
- M8 Small Flat Washer………………………………………………………….. (6)
- M8 x 1.25mm Serrated Flange Nut……………………………………….. (6)
Tools for Installation
- 5mm Allen Wrench
- 13mm Wrench
- 13mm Socket Wrench
NOTE:
This rack allows you the option to securely mount a Farm Jack in the interior
of your Bronco. Notice the Mount and basket has a cutout to accommodate the
Farm Jack. This cutout must be towards the back of the rear seat. This will
assist which rack mount is drivers or passenger side. Use Hand Knob (3),
Washer (4), and Nut (5) to secure the Farm Jack to the basket.
Interior Storage Rack Bronco
Step 1:
Remove the plastic cover in the trunk area that covers the soft-top hinge
mechanism. These covers are attached with clips. Simply pull on the cover to
release the clips.
Step 2:
Soft-Top ONLY: Remove the top two bolts holding the soft-top hinge mechanism.
DO NOT remove the lower third bolt, this will hold the mechanism in place
while mounting the rack mount. Keep these bolts to be reused.
Step 3:
Soft-Top ONLY: Place Rack Mount (2) into place. Reuse the OE bolts to loosely
install this mount. Use the outer slots to mount for soft-top. Hard-Top ONLY:
Use bolt (6), to washer (7), to rack mount (2), into spacer (8). Thread bolt
into the threaded inserts of the vehicle. Use the inner slots to mount for
hard-top.
Note : Keep the cutout near the back of the rear seat. See note on page
Step 4:
With both driver and passenger rack mounts loosely installed, Place rack (1)
into position. This would be best accomplish with as assistant to help hold in
position while installing hardware.
Note : Jack cutout must be towards the back of the rear seat.
Step 5:
Use Button Head Bolt (9) with washer (10) through the rack and mount. Secure
with Flange Nut (11). Requires three on each side. Adjust basket and mounts to
align and level then fully tighten all hardware.
Step 6:
Replace the plastic covers removed from step 1. Press firmly to ensure all the
clips engage
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>