HAVOC OFFROAD HFB-09-001 Mesh Shade Top 2 and 4 Door Bronco Installation Guide

: June 13, 2024
: HAVOC OFFROAD

Table of Contents

HAVOC OFFROAD HFB-09-001 Mesh Shade Top 2 and 4 Door Bronco
Product Information
Product Usage Instructions
Components and Hardware
Mesh Shade Top, 2 & 4 Door Bronco
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HAVOC OFFROAD HFB-09-001 Mesh Shade Top 2 and 4 Door Bronco

HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco-
product

Product Information

Product Name: Mesh Shade Top
Part Number: HFB-09-001
Compatible with: 2 & 4 Door Bronco

Components and Hardware:

Mesh Shade Top – Quantity: 1
Cross Bow – Quantity: 1
Turn Knob – Quantity : 2

Tools for Installation:
No specific tools mentioned in the user manual. However, it is recommended to have general hand tools available for installation.

Product Usage Instructions

Step 1:
Lay the Mesh Shade Top on top of the vehicle. Make sure that the metal hooks are towards the front and facing downward.

Align the eyelet holes on the Mesh Top over the torx head bolts in the front corner.
Remove the inboard factory bolt, pass it through the eyelet, and hand tighten.
Repeat the previous step on the outboard torx bolt.

Step 2:
Insert the metal hooks into the 2 factory metal tabs.

Step 3:
Repeat Step 1 on the Passenger Side. TIGHTEN ALL HARDWARE AT THIS TIME.

Step 4:
Insert the front corner strap into the round hole on the side of the roll-bar and tighten the strap. Repeat this step on the Passenger Side.

Step 5:
Connect the cross bow pieces. Install the middle Support Bow:

For 4-door vehicles, install the cross bow using the forward most hook and loop sleeve.
For 2-door vehicles, install the cross bow using the rear most hook and loop sleeve.

Step 6:
Secure the Support Bow to the roll-bar using either the factory torx head bolt OR the supplied turn knob.

Step 7:
Install the 3 rear straps around the soundbar and the 2 rear corner straps as shown in the user manual.

Step 8:
The flaps at the front corners can be secured open to maintain access to the windshield clamps.

Components and Hardware

$HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco- $1$$

Components and Hardware:

Mesh Shade Top …………………………………………………………………..(1)
Cross Bow…………………………………………………………………………….(1)
Turn Knob……………………………………………………………………………..(2)

Tools for Installation:

T50 Torx

Mesh Shade Top, 2 & 4 Door Bronco

Lay Mesh Top on top of vehicle. Ensure metal hooks are towards the front and are facing downward.

Align eyelet holes on Mesh Top over torx head bolts in front corner. Remove inboard factory bolt, pass bolt through eyelet and hand tighten. Repeat on outboard torx bolt.
$HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco- $2$$
Insert metal hooks into the 2 factory metal tabs.
$HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco- $3$$
Repeat Step 1 on the Passenger Side. TIGHTEN ALL HARDWARE AT THIS TIME.
Insert front corner strap into the round hole on the side of the roll-bar and tighten strap. Repeat on Passenger Side.
Connect cross bow pieces.
Install the middle Support Bow:
4-door, install cross bow using forward most hook and loop sleeve.
2-door, install cross bow using rear most hook and loop sleeve.
$HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco- $7$$
Secure the Support Bow to the roll-bar with either factory torx head bolt OR supplied turn knob.
$HAVOC-OFFROAD-HFB-09-001-Mesh-Shade-Top-2-and-4-Door-Bronco- $8$$
Install the 3 rear straps around the soundbar and the 2 rear corner straps as shown below.
The flaps at the front corners can be secured open to maintain access to the windshield clamps.