SPEC-D Tuning 2019-Up Dodge Ram 1500 Projector Sequential Headlight Installation Guide

SPEC-D Tuning 2019-Up Dodge Ram 1500 Projector Sequential Headlight

BEFORE INSTALLATION

• If you experience any difficulties that the instructions did not cover, please seek assistance at a local automotive shop.
• Please wear proper protective equipment before you work on any vehicle.
• An assistant is recommended when removing the front bumper from your vehicle.
• Please be cautious when working with the bumper or any parts belonging to the vehicle’s body to prevent scratching.
• Do not make direct contact with the halogen bulbs or the wire assembly until the unit has cooled down after use.

TOOLS AND SUPPLIES REQUIRED

INSTALLATION INSTRUCTION

• STEP 1
  Remove the twelve plastic fasteners on the radiator upper support cover

• STEP 2
  Remove the radiator upper support cover

• STEP 3
  Remove the eight 10mm bolts at the top of the upper grille trim

• STEP 4
  Remove the upper grille trim

• STEP 5
  Remove the four 8mm bolts on the fender liner

• STEP 6
  Pull away the fender liner

• STEP 7
  Remove the 10mm bolt

• STEP 8
  Grab the edge and pull forward to unseat the filler panel

• STEP 9
  Grab the other end and pull out to remove the filler panel, repeat for the other side

• STEP 10
  Remove the three 10mm bolts at the bottom of the front grille

• STEP 11
  Remove the four 10mm bolts at the top of side

• STEP 12
  Unseat the front grille upper leg for both the front grille

• STEP 13
  Remove the front grille

• STEP 14
  Remove the 10mm bolt at the bottom of the headlight

• STEP 15
  Remove the 10mm bolt at the top of the headlight

• STEP 16
  Unseat the factory headlight housing

• STEP 17
  Disconnect the headlight harness and remove the factory headlight housing

• STEP 18
  Remove the parking light socket from the factory headlight housing

• STEP 19
  Remove the parking light bulb from the parking light socket

• STEP 20
  Insert the parking light connector from the new headlight housing to the parking light socket, (+) to (+) and (-) to (-)

• STEP 21
  Reinstall the parking light socket to the new headlight housing

• STEP 22
  Connect the headlight harness

• STEP 23
  Seat the new headlight assembly in place

• STEP 24
  Reinstall the 10mm headlight bolt at the top of the headlight

• STEP 25
  Reinstall the 10mm headlight bolt at the bottom of the headlight

• STEP 26
  Please repeat the steps from 13 to 25 for the opposite side

• STEP 27
  Remove the fuse box cover

• STEP 28
  Locate the #35 fuse

• STEP 29
  Remove the #35 fuse

• STEP 30A
  Install the ACC wire fuse to the #35 fuse spot

• STEP 30B
  Install the ACC wire fuse to the #35 fuse spot

• STEP 31
  Reinstall the fuse box cover

• STEP 32
  Connect the ACC wire to the LH headlight connector

• STEP 33
  Connect the ACC wire to the RH headlight connector

• STEP 34
  Start the car to make sure the LED light bar is working before reinstall the front grille

• STEP 35A
  Cable tie the loose wires

• STEP 35B
  Cable tie the loose wires

• STEP 36
  Reinstall the front grille

• STEP 37
  Reinstall the three 10mm bolts at the bottom of the front grille

• STEP 38
  Reinstall the four 10mm bolts at the top of the front grille

• STEP 39
  Reinstall the filler panel

• STEP 40
  Pull away the fender liner and reinstall the 10mm bolt

• STEP 41
  Reinstall the fender liner and the four 8mm bolts

• STEP 42
  Reinstall the upper grille trim

• STEP 43
  Reinstall the eight 10mm bolts at the top of the upper grille trim

• STEP 44
  Reinstall the radiator upper support cover

• STEP 45
  Reinstall the twelve plastic fasteners on the radiator upper support cover

• STEP 46
  Close the hood to complete the installation

• **FINISH

**

BEFORE INSTALLATION

• If you experience any difficulties that the instructions did not cover, please seek assistance at a local automotive shop.
• Please wear proper protective equipment before you work on any vehicle.
• An assistant is recommended when removing the front bumper from your vehicle.
• Please be cautious when working with the bumper or any parts belonging to the vehicle’s body to prevent scratching.
• Do not make direct contact with the halogen bulbs or the wire assembly until the unit has cooled down after use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>