HUBBARDTON FORGE 302580 Tura Sconce Small Instruction Manual

HUBBARDTON FORGE 302580 Tura Sconce Small

Product Information

• Product Name: Tura Sconce Small 302580
• Model Number: B503
• Component Parts
  • A – Fixture
  • B – Crossbar
  • C – Ground Screw
  • D – Knurled Balls (2)
  • E – Threaded Stud (2)
  • F – Caulking Lip
  • G – Socket
  • H – Bulb (Not Included)
  • I – Glass
  • J – Retaining Ring
  • K – Retaining Ring Tool
  • L – White Washer

Product Usage Instructions

Installation of Fixture

1. Make sure the power is off at the main breaker box before installation.
2. Carefully unpack the fixture (A) from the carton.
3. Thread two studs (E) into the appropriate holes in the crossbar (B) that align with fixture (A) and desired orientation.
4. Attach the crossbar (B) to the electric box using two machine screws (not provided), using the outer oval holes to orient the fixture. Note: If replacing a fixture, retain the existing screws for use with the new fixture.
5. Adjust the studs (E) to the proper length to ensure the fixture fits snugly against the wall.
6. Connect the fixture wires to the supply using suitable wire connectors (not provided). Connect the ground wires as well.
7. Apply a generous bead of suitable caulking material (not provided) to the caulking lip (F) on the fixture.
8. Tuck all wires behind the fixture and push the fixture firmly against the wall.
9. Secure the fixture by threading the knurled balls (D) onto the threaded studs (E). Make sure no wires are pinched between the wall and the fixture, and ensure that the threaded studs are fully seated in knobs.
10. Refer to the instructions on the last page to install the glass.

Installation of Glass

1. Remove and retain the retaining ring (J) that is shipped installed. Carefully unpack the glass (I).
2. Slide the glass (I) over the socket (G), followed by the white washer (L).
3. Using the provided retaining ring tool (K), secure both the glass and white washer with the retaining ring (J). Do not over tighten to avoid breaking the glass.
4. Install the bulb (H), not included, into the socket (G).
5. Restore electricity at the main breaker.

If you need further assistance or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!

• Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping, or use of this fixture.

Component Parts

• A Fixture
• B Crossbar
• C Ground Screw
• D Knurled Balls (2)
• E Threaded Stud (2)
• F Caulking Lip
• G Socket
• H Bulb – Not Included
• I Glass
• J Retaining Ring
• K Retaining Ring Tool
• L White Washer

ASSEMBLY & INSTALLATION INSTRUCTIONS

Tura Sconce Small 302580

• CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician. This product must be installed in accordance with applicable installation code(s), by a person familiar with the construction and operation of the product and the hazards involved.*
• Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
• Please Note : After installation extra hardware and accessories are possible; our kits are used on multiple products.

To Install Fixture (Figure 1 & 2 – On following page)

CAUTION: BE SURE POWER IS OFF AT THE MAIN BREAKER BOX PRIOR TO INSTALLATION.

1. Carefully unpack the fixture (A) from the carton.

2. Thread two studs (E) into the appropriate holes in the crossbar (B) that align with fixture (A) and desired orientation.

3. Using two machine screws (not provided) attach crossbar (B) to the electric box using outer oval holes to orient fix- ture.
   Note: A new electric box comes with screws. When replacing a fixture, retain the existing screws for use with the new fixture.

4. Adjust the studs (E) to proper length to ensure the fixture will fit snugly against the wall.

5. Using suitable wire connectors (not provided) connect fixture wires to supply (white to white and black to black). At-tach a pigtail lead to the crossbar ground screw (C). Connect all ground wires (bare copper or green to bare copper or green).
   CAUTION: MAKE SURE WIRE CONNECTORS ARE TWISTED ON SECURELY, AND NO BARE WIRE IS EXPOSED.

6. Apply a generous bead of a suitable caulking material (not provided) to caulking lip (F) on the fixture (Figure 2).

7. Carefully tuck all wires behind fixture, push fixture firmly against the wall. Secure by threading knurled balls (D) onto threaded studs (E).
   Note: Be sure no wires are pinched between the wall and the fixture. Be sure threaded studs are fully seated in knobs.

8. See instructions on last page to install glass.

To Install Glass (Figure 3)

1. Retaining ring (J) is shipped installed. Remove and retain for next steps.

2. Carefully unpack glass (I).

3. Slide glass (I) over socket (G) followed by white washer (L) and, using tool (K) provided, secure both with retaining ring (J).
   Note: Be sure not to over tighten as this could break the glass (N).

4. Install bulb (H), not included, into socket (G).

5. Restore electricity at the main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased this product. We hope you enjoy your fixture!

• Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>