BOSCH FPE-7039 MUX Expansion Module Instruction Manual

June 13, 2024
Bosch

BOSCH FPE-7039 MUX Expansion Module

BOSCH-FPE-7039-MUX-Expansion-Module-product

Product Information

Product Name MUX Expansion Module
Model Number FPE-7039
Manufacturer Bosch Security Systems. Inc.
Version 1.0

Product Usage Instructions

  1. Before installing the MUX Expansion Module, ensure you have read and understood the Installation and Operation Guide for the control panel you are using.
  2. Install, test, and maintain the module according to the provided instructions, NFPA codes, local codes, and the authority having jurisdiction (AHJ).
  3. Ensure all power is removed before making any electrical connections to avoid personal injury and/or damage to equipment.
  4. Perform a complete system-wide functional test following any modifications, repairs, upgrades, or adjustments made to the system’s components, hardware, wiring, programming, and software/firmware as required by NFPA 72.

Note: Failure to follow these instructions can result in the failure of a detector to initiate an alarm event. Bosch Security Systems, Inc. is not responsible for improperly installed, tested, or maintained devices.

Notices
These instructions cover the installation of the FPE-7039 Multiplex Expansion Module in a fire system supervised by an FPD-7024 Fire Alarm Control Panel (FACP).
Open Source Software information

Notice!
For general information regarding open-source software in
Bosch Security Systems please visit http://www.boschsecurity.com/oss.

MUX expansion module

This product may contain the following open-source components:
BSD 3-clause “New” oz “Revised” License:

  • ARM CMSIS (limited to CMSIS/Include directory) (1.00)|
  • ProtoThreads (1.4)
  • STMicroelectronics software License agreement liberty v2:
  • SIM32F10x StdFeriphDriver (3.6.1)|
  • License Texts
  • Component: ARM CMSIS (limited to CMSIS/Include directory)|
  • Version: 4.00
  • UrL: http://www.arm.com/.
  • License Type: BSD 3-clause “New” or “Revised” License
  • Copyright (c) 2009 – 2014 ARM LIMITED
  • All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
  • Redistributions of source code aust retain the above copyright notice, this list of conditions and the following disclaimer.
  • Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other naterials provided with the distribution.
  • Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
    THIS SOFTWARE IS PROVIDED BY THE COPYRIGET HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; TOSS OF USE, DATA, OR PROFITS: OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT STABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY KAY OUT OF THE USE OF THIS SOFTWARE, EVEN IP ADVISED OF THE POSSIBILITY OF SUCH DAMAGE

Component: ProtoThreads
Version: 1.4
URL: http://dunkels.com/adam/pt/
License Type : BSD 3-clause “New” or “Revised’ License
Copyright (c) 2004-2005, Swedish Institute of Computer Science.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are a mess

  1. Redistributions of source code must retain the above copyright notice, this list of conditions, and the following disclaimer.
  2. Redistributions in binary form must reproduce the above copyright. notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  3. Neither the name of the Institute nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE INSTITUTE AND CONTRIBUTORS ‘AS IS’ AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ARE DISCLAIMED. IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES, LOSS OF’ USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDINGNEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

  • Component: STM32F10x StaPeriphDriver
  • Version: 3.6.1
  • URL: http://www.85.com/.
  • License Type: STMicroelectronics software licenge agreement liberty v2
  • SOFTWARE LICENSE AGREEMENT

By using this Licensed Software, You are agreeing to be bound by the terms and conditions of this License Agreement.
Do not use the licensed Sottwaro unit You have read and agreed to tne following terms and conditions.
The use of the Licensed Software implies automatically the acceptance of the following terms and conditions.

DEFINITIONS
Licensed Software: means the enclosed SOFTWARE/FIRMWARE, EXAMPLES, PROJECT TEMPLATE and all the related documentation and design tools licensed and delivered in the form of object and/or source code as the case may be.
Product: means Your and Your’s end-users product or system, and all the related documentation, that includes or incorporates the Licensed Software and provided further that such Licensed Software or derivative works of the Licensed Software execute solely and exclusively on microcontroller devices manufactured by or for ST.
LICENSE
STMicroelectronics (“ST”) grants You a non-exclusive, worldwide, non- transferable (whether by assignment or otherwise unless expressly authorized by ST) non sub-licensable, revocable, royalty-free limited license of the Licensed Software to:

  • make copies, prepare derivative works of the source code version of the Licensed Software for the sole and exclusive purpose of developing versions of such Licensed Software only for use within the Product;
  • make copies, and prepare derivative works of the object code versions of the Licensed Software for the sole purpose of designing, developing and manufacturing the Products;
  • make copies, and prepare derivative works of the documentation part of the Licensed Software (including non confidential comments from source code files if applicable), for the sole purpose of providing documentation for the Product and its usage;
  • make, have made, use, sell, offer to sell, import and export or otherwise distribute Products also through multiple tiers.

OWNERSHIP AND COPYRIGHT
Title to the Licensed Software, related documentation, and all copies thereof remain with ST and/or its licensors. You may not remove the copyright notices from the Licensed Software and to any copies of the Licensed Software. You agree to prevent any unauthorized copying of the Licensed Software and related documentation.

RESTRICTIONS
Unless otherwise explicitly stated in this Agreement, You may not sell, assign, sublicense, lease, rent or otherwise distribute the Licensed Software for commercial purposes, in whole or in part. You acknowledge and agree that any use, adaptation, translation or transcription of che Licensed Software or any portion or derivative thereof, for use with processors manufactured by or for an entity other than ST is a material breach of this Agreement and requires a separate license from ST.
No source code relating to and/or based upon Licensed Software is to be made available or sublicensed by You unless expressly permitted under the Section “License”

You acknowledge and agree that the protection of the source code of the Licensed Software warrants the imposition of reasonable security precautions. In the event ST demonstrates to You a reasonable belief that the source code of the Licensed Software has been used or distributed in violation of this Agreement, ST may, by written notification, request certification as to whether such unauthorized use or distribution has occurred. You shall cooperate and assist ST in its determination of whether there has been unauthorized use or distribution of the source code of the Licensed Software and will take appropriate steps to remedy any unauthorized use or distribution.

NO WARRANTY
The Licensed Software is provided “as is” and “with all faults” without warranty of any kind expressed or implied. STand its licensors expressly disclaim all warranties, expressed, implied or otherwise, including without limitation, warranties of merchantability, fitness for a particular purpose, and noninfringement. of intellectual property rights. ST does not warrant that the use in whole or in part of the Licensed Software will be interrupted or error-free, will meet your requirements or will operate with the combination of hardware and software selected by You. You are responsible for determining whether the Licensed Software will be suitable for your intended use or application or will achieve your intended results.ST will not be liable to You and/or to any third party for the derivative works of the Licensed Software developed by You.
ST has not authorized anyone to make any representation or warranty for the Licensed Software, and any technical, applications or design information or advice, quality characterization, reliability data or other services provided by ST shall not constitute any representation or warranty by ST or alter this disclaimer or warranty, and in no additional obligations or liabilities shall arise from ST’s providing such information or services. ST does not assume or authorize any other person to assume for it any other liability in connection with its Licensed Software.
Nothing contained in this Agreement will be construed as:

  • a warranty or representation by ST to maintain production of any ST device or other hardware or software with which the Licensed Software may be used or to otherwise maintain or support the Licensed Software in any manner; and
  •  a commitment from ST and/or its licensors to bring or prosecute actions or suits against third parties for infringement of any of the rights licensed hereby, or conferring any rights to bring or prosecute actions or suits against third parties for infringement.

However, ST has the right to terminate this Agreement immediately upon receiving notice of any claim, suit or proceeding that alleges that the Licensed Software or your use or distribution of the Licensed Software infringes any third party intellectual property rights. All other warranties, conditions or other terms implied by law are excluded to the fullest extent permitted by law.

LIMITATION OF LIABILITIES
In no event ST or its licensors be liable to You or any third party for any indirect, special, consequential, incidental, punitive damages or other damages (including but not limited to, the cost of labor, re-qualification, delay, loss of profits, loss of revenues,loss of data, costs of procurement of substitute goods or services or the like) whether based on contract, tort, or any other legal theory, relating to or in connection with the Licensed Software, the documentation or this Agreement, even if ST has been advised of the possibility of such damages. In no event shall ST’s liability to You or any third party under this Agreement, including any claim with respect of any third party intellectual property rights, for any cause of action exceed 100 uss. This section does not apply to the extent prohibited by law. For the purposes of this section, any liability of ST shall be treated in the aggregate.

TERMINATION
ST may terminate this License Agreement license at any time if You are in material breach of any of its terms and conditions and You have failed to cure such breach within 30 (thirty) days upon occurrence of such breach. Upon termination, You will immediately destroy or return all copies of the Licensed Software and documentation to ST. After termination, You will be entitled to use the Licensed Software used in Products tha: include microcontroller devices manufactured by or for ST, purchased by You before the date of the breach. APPLICABLE LAW AND JURISDICTIONIn case of dispute and in the absence of an amicable settlement, the only competent jurisdiction shall be the Courts of Geneva, Switzerland. The applicable law shall be the law of Switzerland
SEVERABILITY
If any provision of this agreement is or becomes, at any time or for any reason, unenforceable or invalid, no other provision of this agreement shall be affected thereby, and the remaining provisions of this agreement shall continue with the same force and effect as if such unenforceable or invalid provisions had not been inserted in this Agreement.
RAIVER
The waiver by either party of any breach of any provisions of this Agreement shall not operate or be construed as a waiver of any other or a subsequent breach of the same or a different provision.
ASSIGNMENT
This Agreement may not be assigned by You, nor any of Your rights or obligations hereunder, to any third party without prior written consent of the other party (which shall not be unreasonably withheld).  In the event that this Agreement is assigned effectively to a third party, this Agreement shall bind upon successors and assigns of the parties hereto.

RELATIONSHIP OF THE PARTIES
Nothing in this Agreement shall create, or be deemed to create, a partnership or the relationship of principal and agent or employer and employee between the Parties. Neither Party has the authority or power to bind, to contract in the name of or to create a liability for the other in any way or for any purpose.

Regulatory and safety
Before installing the module, become familiar with the Installation and Operation Guide for the control panel you are using.
Install, test and maintain the module according to these instructions, NFPA codes, local codes, and the authority having jurisdiction (AHJ). Failure to follow these instructions can result in the failure of a detector to initiate an alarm event. Bosch Security Systems, Inc. is not responsible for improperly installed, tested or maintained devices.

Warning!
Follow these instructions to avoid personal injury and damage to equipment.

NFPA 72 requires that you perform a complete system-wide functional test following any modifications, repairs, upgrades or adjustments made to the system’s components, hardware, wiring, programming and software/firmware.

Description

The FPE‑7039 MUX expansion module is designed to enhance the conventional features of the D7024 or FPD-7024/DS9400 Fire alarm control panels (FACPs). The module connects directly to the FACP for either two Class B multiplex buses or one Class A multiplex bus. When installed as two Class B multiplex buses, you can program addresses 9 through 255. When installed as one Class A multiplex bus, you can program addresses 9 through 128. The module also increases the number of relay outputs (to 58 on the D7024/DS9400 control panels and 59 on the FPD‑7024 control panels). It adds an additional 400 events to the history buffer for a total of 499 non‑volatile events. It also allows for up to 100 system users (an addition of 84 PINs from the base system). The module can be programmed remotely from a PC using RPS Remote programming software. The module can be used with the Bosch Security Systems, Inc. control panels and modules indicated in the following table.

Control panels

Active:| FPD-7024 Fire alarm control panels
**Legacy:*| D7024 Fire alarm control panels
DS9400 Control panels
Modules
Active:**| D7042 Multiplex eight-input remote module
 | D7042B Multiplex eight-input remote module with enclosure
 | D7044 Multiplex single-input module
 | D7044M Multiplex mini single-input module
 | D7050 Addressable photoelectric smoke detector
---|---
 | D7050DH Addressable photoelectric duct smoke detector head
 | D7050TH Addressable photoelectric smoke/ heat detector
 | D7050-B6 Smoke detector base
 | D7052 Multiplex dual-input module
 | D7053 Multiplex Input-output module
 | FLM-7024-ISO MUX bus isolator module
 | FMM-7045 Multiplex addressable manual pull station
 | FMM-7045-D dual-action multiplex addressable manual pull station

  • Legacy products were investigated to comply only to UL864 8th edition

Mounting

Danger!
Make sure all power is removed before making any electrical connections. Failure to do so may result in personal injury and/or damage to equipment.

Caution!
Static-sensitive components! The FACP and modules contain static‑sensitive components and must be handled with care. Follow proper antistatic handling procedures.

FPE-7039 board mountingBOSCH-FPE-7039-MUX-Expansion-Module-
FIG-1

Figure 3.1: Mounting the FPE-7039

1 FPE-7039 2 FACP
3 Mounting holes (4) for plastic standoffs 4 FACP connector pins (align

with FPE-7039)
5| Mounting screw| 6| Ground wire

If the FACP (see callout 2 in the above figure) is already installed in an enclosure, remove it.

  1. Place the FACP on a flat surface with the component side facing up.
  2. Insert the four plastic standoffs in the mounting holes (callout 3 above) without bending or flexing the FACP.
  3. Align the standoff tabs so they do not touch the module components.
  4. Firmly press the standoffs into the board, allowing the ears to expand out.
  5. Mount the board (callout 1 above) on the standoffs ensuring the connector pins (callout 4 above) are properly aligned.
  6. Install the FACP in the enclosure.
  7. Use the mounting screw (callout 5 above) to secure the FPE‑7039’s ground wire (callout 6 above) to the FACP.

I/O module mountingBOSCH-FPE-7039-MUX-Expansion-Module-
FIG-2

Figure 3.2: Mounting the FPE-7039 I/O module

1 FACP enclosure 2 FPE-7039 I/O module
3 Plastic standoffs (3) 4 4-wire (red, black, yellow, green) harness
5 Connector terminal plug 6 Yellow/green wire connecting the I/O module to

the FACP ground terminal
---|---|---|---

If the FPE-7039 board is not mounted to the FACP board, mount it using the instructions above.

  1. Insert the three plastic standoffs (see callout 3 in the above figure) in the mounting holes in the enclosure.
  2. Mount the I/O module (callout 2 above) in the FACP enclosure (callout 1 above).
  3. Connect the wire harness of the I/O module to the terminal on the FPE-7039 (callout 5 above).
  4. Connect the yellow and green earth ground wire (callout 6 above) to the FACP‘s earth ground terminal.

Wiring

You can configure the FPE‑7039 with a single fault-tolerant Class A loop or as a pair of supervised Class B branches. For programming information, see the FPD‑7024 Installation and Operation Guide (IOG).

Determining system limits

Notice!
Do not use shielded wire. The twisted-pair wire is not recommended but is acceptable if wire length is reduced by 50%.

Notice!

In the following graphs,

  • data points falling in the light area are acceptable.
  • data points falling in the middle area depend on your configuration. They must be verified with the battery calc table.
  • data points falling in the dark area require changes in wire length or size, number of devices, or configuration.
  1. Find the intersection of the desired number of devices and wire length/resistance you want on the first graph below. If the data point falls in the light area, note the available wire sizes (AWG or ISO) for your installation. Then go to the next step. If it does not, see the Notice above.
  2. Look up the capacitance for the specific wire size/length/ type.
  3. Check the intersection point of the capacitance and number of devices on the second chart below. If the data point falls in the light area, your choices are acceptable. If not, see the Notice above.BOSCH-FPE-7039-MUX-Expansion-Module-FIG-3

Maximum wire length

Maximum wire resistance| 50 Ω at +20°F (+68°C), depending on method and wire size used
Wire length| 5950 ft. (1810 m), depending on wire size and number of devices
Wire capacitance*| <0.12 μF (maximum per bus), depending on wire size and number of devices

Maximum wire length

This table gives capacitance in microFarads (μF), but the graph gives it in nanoFarads ( nF). For example, 0.12 μF = 120 nF.

Wiring the loops
Determine the appropriate configuration (number and type of devices and wire size and length).

  1. Run solid wire from the FACP to the device locations and connect the multiplex loop.BOSCH-FPE-7039-MUX-Expansion-Module-FIG-4

Figure 4.1: Wiring Class A loops and Class B branches

1 I/O module wired as Class A 2 Wiring harness
3 Ground wire 4 Class A loop (addresses 9 to 128)
5 I/O module wired as Class B 6 Wiring harness
7 Ground wire 8 Class B branch (addresses 129 to 255)
9 Class B branch (addresses 9 to 128)

All MUX terminals are power-limited and supervised

  • Ensure the loop is disconnected from the FPE‑7039 Module.
  • Measure loop resistance by shorting: the end of the farthest device in Class B. the return wire in Class A.
  • Read the total resistance of all wires associated with the loop.BOSCH-FPE-7039-MUX-Expansion-Module-FIG-5

Figure 4.2: Measuring Class B loop resistance

1 50 Ω maximum 2 MUX bus wires
3 Clip lead

BOSCH-FPE-7039-MUX-Expansion-Module-FIG-6

C 50 Ω maximum 2 MUX bus wires
3 Clip lead

Specifications

Environmental

Environment Indoor, dry

Power

Current Draw

Alarm

Load, Class A Load, Class B Standby

| ****

190 mA maximum

100 mA maximum

100 mA maximum for each bus 190 mA maximum

---|---
Bus Voltage| 8.5 V to 13 V
Wire Resistance (maximum)| 50 Ω Class A or Class B

  • Bosch Security Systems, Inc.
  • 130 Perinton Parkway
  • Fairport, NY 14450
  • USA
  • www.boschsecurity.com.
  • © Bosch Security Systems, Inc., 2016
  • Bosch Sicherheitssysteme GmbH
  • Robert-Bosch-Ring 5
  • 85630 Grasbrunn
  • Germany

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals