YENKEE YHP 01BTWE True Wireless Earphone User Manual

June 6, 2024
YENKEE

YENKEE YHP 01BTWE True Wireless Earphone

YENKEE YHP 01BTWE True Wireless Earphone

PARTS LIST

  1. Charging contacts
  2. LED indicator
  3. Multifunction button
  4. Multifunction touch button
  5. Charging contacts
  6. Headphone LED indicator
  7. Microphone
  8. USB-C charging connector

Putting into operation

Before first use, be sure to read the safety instructions contained in this user’s manual carefully. Before first use, please charge the BT headphones to a maximum level. The headphones are automatically ready to use after removing from the charging box.

Caution: To prevent damage to your hearing, before connecting the BT headphones to your mobile phone, make sure that your device’s volume level is always set to minimum.

Note: The BT headphones will turn off after a longer period of inacti­vity unless they are paired to another device.

Pairing your headphones via Bluetooth

You can start pairing the BT headphones with your mobile device using one of the following procedures:

a) When used for the first time, the headphones will automatically turn on after opening the charging box will be ready for pairing to your mobile device.
b) While the headphones are placed in the charging box, long-press the multifunction button in the box for 3 seconds until the LED indi­cator next to the multifunction button starts flashing slowly in white. The LED indication notifies of starting the pairing mode. While the BT headphones are being paired to your mobile device, leave the char­ging box open.

Then, find the Bluetooth headphones narne “Gemini” in the device to which you wish to pair and start the pairing process. If you are requested to enter a pairing code while your device and the BT headphones are pairing, use the following code: “ODDO”.
To cancel the pairing process, disconnect the BT headphones from your mobile device [cancel the Bluetooth pairing]

Note: To ensure a stable Bluetooth connection, make sure that the dis­tance between the BT headphones and your paired device is kept within 10 meters. Depending on the surrounding interference, it is sometimes ne­cessary to keep a shorter distance between the BT headphones and your paired device.

Headphone LED indicator

  • The headphones are correctly inserted in the charging box – solid orange LED lights
  • The headphones are in the state of searching for an already paired Bluetooth device – orange slowly flashing LED
  • The headphones are connected to another device via Bluetooth – orange LED goes out
  • The headphones are in the pairing mode – fast flashing orange LED

Operation of the BT headphones

Turning the BT headphones off: Inserting the BT headphones in the char­ging box will disconnect them from the Bluetooth transmission and turn them off automatically.
Answering/ending a phone call: To answer an incoming call to a paired mobile device on the BT headphones, tap twice the multifunction touch button area on the headphone. To hang up an ongoing call, tap twice the multifunction touch button on the headphone.

Rejecting an incoming call: To reJect an incoming call to a paired mobile device, hold down the multifunction touch button area on the headphone for several seconds until the call is rejected.
Switching the ongoing call between the BT headphones and your mobile device: During an ongoing call, hold down the multifunction button area on the headphone for several seconds.

Ta start/pause the music playback: To start/pause the music playback from your connected mobile device, tap twice the multifunction touch bu­tton area on the headphone.

Ta skip ta previous/next track being played: To skip to previous track du­ring the music playback from your connected mobile device, hold down the multifunction touch button area on the left BT headphone for several seconds [to skip to next track, penform the same procedure on the right BT headphone].

Charging
A charged battery provides power for several hours of operation at normal volume levels. A high volume consumes more battery power; therefore, we recommend listening at normal volume levels.
If the BT headphones are placed in the charging box, the LED inside the box shows the BT headphones charging status:

a. Orange indication – the BT headphones are not fully charged and their charging is in progress
b. Green indication – the BT headphones are fully charged and their charging is finished

If the BT headphones are located outside the charging box, the LED indicator inside the box shows the charging box status:

a. Orange flashing indication – charging box battery level <10%
b. Orange solid indication – charging box battery level 10-50%
c. Green indication – charging box battery level 50-100%

You can verify the charging box battery level even while your BT headphones are being charged. To do so, press the multifunction button inside the box briefly.
While the box charging is in progress, the LED inside the box shows the charging status:

a. Orange indication – the box is being charged
b. Green indication – the charging box is fully charged

Caution: For charging, use only the original accessories supplied with the appliance. To achieve the maximum battery lifetime, it is best to start charging the battery after the low battery power notification. Charge continuously until fully charged. When the battery operating time becomes very short. the battery lifetime has been used up; we recommend that you have the battery replaced at your authorized centre.

Recommendation: If your headphones are not to be used for an ex­tended period of time, we recommend to fully charge the batteries once every two to three months. We recommend to store the BT headphones and the charging box with the battery charged to pre­vent irreparable damage to the battery [loss of capacity].

Factory settings
To erase the history of mobile devices paired to your BT headphones, reset your BT headphones to default factory settings. Insert the BT headphones in the charging box, leaving the box open. Hold down the multifunction button inside the charging box forl □ seconds until the LED inside the charging box lights 5 times in green.

Specification

Bluetooth: v5.0
BT profiles: A2DP AVRCP HFP HSP
Operating range: 75 m
Charging voltage: DC 5V [Type C] Charging time: s 2 h
Playback time: up to 4 h
Stand-by time up to 60 h
Speakers diameter: 10 mm
Frequency response: 2□-2□Khz
Sensitivity: 92±3D
lmpendance: 320± 10%
Maximum transmitter power at 2.4 GHz – 2.4835 GHz: 3mW
Charging case capacity: 500 mAh
Earphone capacity: 35 mAh
Charging case dimensions: 73 x39 x 28 mm
Earphone dimension: 41 x12 xll mm
Charging case weight: 44 g
Earphone weight: 3.5 g

Instructions and information regarding the disposal of used packaging materials
Dispose of packaging material at a public waste disposal site.

Disposal of used electrical and electronic appliances
The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this product at your applicable collection point for the recycling of electrical & electronic equipment waste. Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product.

The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative im pact on the environment and human health, which could be caused as a result of improper liquidation of waste. Please ask your local authorities or the nearest waste collection centre for further details. The improper disposal of this type of waste may fall subject to national regulations for fines.

For business entities in the European Union
If you wish to dispose of an electrical or electronic device, request the necessary information from your seller or supplier.

Disposal in other countries outside the European Union
If you wish to dispose of this product, request the necessary information about the correct disposal method from local government departments or from your seller. This appliance complies with EU rules and regulations regarding electromagnetic and electrical safety.

Changes to the text, design and technical specifi cations may occur without prior notice and we reserve the right to make these changes.
Hereby, FAST CR, a.s. declares that the radio equipment type [YHP 018T WE] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.yenkee.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals