algam Eventpar Mini Led Projector User Manual

: June 13, 2024
: algam

Table of Contents

SAFETY INSTRUCTIONS
INSTALLATION
PRODUCT INSTALLATION
RIGGING
OPERATION INSTRUCTIONS
MENU OPERATING INSTRUCTION
IR REMOTE CONTROLLER
WIRELESS DMX
DMX PROTOCOL
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

algam Eventpar Mini Led Projector User Manual

Thank you for choosing one of our Algam Lighting products. Please read this user’s manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user’s guide for future reference.

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols to warn of potential hazards related to the use of electrical dangers associated with the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:

ATTENTION !
Before using your equipment, we recommend that you read all the instructions in this manual.

ATTENTION !
This device produces an intense and powerful light. Risk to the eyes. Do not look directly into the beam.

DANGER !
Hazardous voltage, risk of electric shock. Do not open the product. To reduce the risk of electric shock do not expose this equipment to rain or moisture.

ATTENTION !
Risk of burns. The exterior of the unit can become very hot. Do not touch within 10 minutes of use.

ATTENTION !
Fire hazard. Keep all combustible and flammable materials away from the materials away from the unit during operation.

DANGER !
Safety hazard. This appliance presents a significant risk of injury. Follow the safety instructions.

Place the unit at least 50cm away from flammable materials and walls.

ATTENTION !
This product contains button cell batteries. KEEP OUT OF REACH OF CHILDREN.

Ingestion may result in chemical burns, soft tissue perforation and death. Severe burns may occur within 2 hours of ingestion. Seek immediate medical attention.

Do not give to food or drink, and do not induce vomiting. If you have the battery packaging, present it to the doctors when you take over. Do not use if battery compartment is damaged or does not close. Do not allow children to replace batteries without adult supervision. Remove used batteries immediately and dispose of them in an appropriate recycling facility.

USAGE
Always select the correct battery size and type for the intended use. Follow the instructions on the device. Always insert batteries correctly, paying polarities (+ and -) marked on the battery and the equipment. Replace all batteries in a set at the same time. Do not short-circuit batteries. Do not charge batteries. Do not force discharge. Store batteries in a well- ventilated, dry place at a moderate temperature.

INSTALLATION

Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.
This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanging point) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for the weight of the device.
This unit is intended for indoor use only. Exposing the unit to rain or moisture may result in electric shock or fire.
Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.
For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit must be equipped with a fuse or circuit breaker and a differential protection device.
Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to the power outlet. This way, in case of an emergency, you can disconnect the power plug immediately.
The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the unit.

USAGE

This appliance must not be used by persons (including children) with limited physical, physiological or mental capabilities or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by that person in the operation of the appliance.
Never leave this equipment unattended.
If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
NEVER use the unit under the following conditions:
- In areas subject to vibration or bumps,
- In places where the ambient temperature is above 45 ° C or below 2 ° C.
- In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).
Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire.
The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.
It is important to use the supplied power cable (grounded cable).
Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.
Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!
Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.
Do not connect this device to a dimmer pack
DO NOT allow liquids or objects to enter the unit. If liquid is spilled on the unit, immediately UNPLUG the power supply to the unit and contact customer service.
You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or a lightning storm, unplug the unit from the mains.
Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!

SAFETY WARNING – RECHARGEABLE BATTERIE

Follow the manufacturer’s instructions; failure to observe the safety instructions may result in serious property damage and serious personal injury.
Do NOT modify the equipment without prior authorization. The battery must not be replaced by unauthorized persons..
The battery must not be replaced by another brand or one with different technical specifications.
Keep out of reach of children during use and/or charging.

CHARGING

Use only the original charger supplied with the equipment.
There is a danger of overcharging rechargeable batteries. The power supply to the equipment must be switched off after the batteries have been fully charged, and charging time must not exceed 2 hours.
Adult supervision is required throughout the charging process.
Products fitted with batteries must not be charged in environments temperature range [0-40°C].
When charging, place the device and charger on a non-flammable, heat-resistant, non-conducting surface away from any flammable materials or sources.
If the battery becomes too hot, remove it immediately from the charger and wait for the battery to cool before using or charging.
Do not recharge equipment with deformed or swollen batteries.

USAGE

Product battery may explode or emit toxic substances. Risk of fire or burns. Do not open, crush, tamper with, disassemble or incinerate.
Products fitted with batteries must not be used in environments exceeding the temperature range [0-60°C].
The product must not be exposed to excessive heat (e.g. sunlight, fire, etc.). Do not exceed a temperature of 60°C during use or storage. Avoid combustible materials around the battery area.
Protect from water and moisture. Do not spill liquid on equipment, charger or battery.
If the product or its battery is damaged, stop using the product immediately, and store the equipment and battery in a well-ventilated place, on a non-flammable, heat-resistant, non-conductive surface and away from all flammable materials or sources. Keep the equipment under surveillance and contact an authorized repairer.
Unplug charger from wall socket after use.
Consider environmental aspects when disposing of the battery. Follow local instructions for battery collection.

MAINTENANCE / SERVICE

Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes void. Repairs by unqualified persons may result in damage or malfunction. Please contact the nearest authorized service center. The light source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent qualification.
Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.
The lamp should be replaced if it has been damaged or deformed by heat.
Disconnect the unit from the mains before servicing.
If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the manufacturer or its service agent only.
Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.
CAUTION : To reduce the risk of fire replace fuse with same type and rating.

PRODUCT INSTALLATION

POWER SUPPLY
Power adapter included.

Power IN: 100-240V~
Power OUT: 16,8V DC 2000mA

DMX CONNECTION
Connection between laser lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XL plug/socket to connect the DMX output/input interface. The connection between socket and cable as below (note the plug/socket’s 3 pin number and position).

DMX-OUTPUT
XLR mounting-sockets (rear view)

DMX-INTPUT
XLR mounting-plugs (rear view)
Instructions

When using standard DMX512 control signal, the last device’s output interface must be connected to a DMX plug.
This plug is putting a 120 ohm resistance between “canon” plug’s 2 pin and 3 pin. Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the interference during the process of signal transmission.

RIGGING

Attention! The installation must be carried out by qualified service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certified installation materials should be used, the installed device should be inspected regularly for safety

OPERATION INSTRUCTIONS

Operation Instructions

Digital display
WDMX receiver/transmitter built-in module : Button to switch on wireless
WDMX receiver/transmitter built-in module : Wireless status indicator
Keyboard – menu and function access
RJ-45 connector DMX IN & OUT (please use included adapter RJ45/XLR)
DC power IN
Main power switch

Mode Option, to choose the operating mode of laser.

Confirmation, to confirm the laser to show the present mode at the next operation.

UP/DOWN, to change operating mode, parameter or DMX address.

DISPLAY SHOW	VALUE	FUNCTION
1 D001	001- 512	DMX512 address setting -4-channel mode
2 A001	000-555	DMX512 address setting -8-channel mode
3 100	000-100	Percentage of electricity displayed
4 S-SL	SL / FA	DMX512 dimming speed setting SL: slow dimming FA: fast

Menu Operating

IR REMOTE CONTROLLER

Remote Controller

BUTTON	FONCTION
1 AUTO	Automatic mode will enable you to run the automatic programs on the

product. Press on the
remote controller, display shows “CC10”. Press or to either increase or decrease the speed
of programm. Press to turn off the auto mode.
2 BLACK OUT| Press off existing mode. Press return the last modes.
3 STROBE| Strobe effect for automatic mode, sound control and preset colors. Press on the remote
controller. Press again, it’s 25% speed, press the 2nd time, it’s 50% speed, press the 3rd time,
it’s 75% speed, press the 4th time, it’s 100% speed. Press again to turn off the strobe function.
4 %

| % mode will enable you to run the color pulse programs on the product. Press on the remote
controller, display shows “CC15”. Press or to either increase or decrease the speed of program. Press to turn off the color pulse mode.
5 0-9| 0-9 kinds Static color mode, press one time for your wanted color, press or to either
increase or decrease brightness.
6 SPEED| No function
7 SOUND| Sound-Active mode will enable the product to respond to the music. Press on the remote
controller. Press and then press or to either increase or decrease the sound sensitivity.
Press return the last modes.
8 SENSITIVITY| Y To adjust sound sensitivity for in Sound-Active mode, press on the remote controller and then
press or to either increase or decrease the sound sensitivity.
9 FADE| It is a color gradient mode. Press on the remote controller, then Press again to turn off the
Fade mode. Press or to either increase or decrease the speed of the program.
10 MANUAL| Press one time, the menu display show “dIon”, turn on the remote controller. Press
to choose your Wanted colour. Press the 1st time, it is 20% brigtness, press the 2nd time, it is
40% birghtness, press the 5th time, it is 100% bightness, press the 6th time, turn off the manual color
which you chosen.

WIRELESS DMX

This ALGAM LIGHTING fixture is equipped with a DMX wireless transmission system. “WIRELESS DMX”.

PAIRING YOUR DMX FIXTURE

Connect the transmitter (Algam Lighting DMX-WT) to your DMX controller OUTPUT or turn ON the EVENTPAR MINI set up as transmitter.
Power up transmitter and the EVENTPAR MIN receiver.
Press the pairing button on the EVENTPAR MINI’s WIRELESSDMX receiver 2 for 4 seconds, and the LED 3 will flash blue. When you release the button, the LED 3 turns white, indicating that your receiver is waiting to be paired.
Press now on transmitter button to start pairing. Both receiver and transmitter will blink rapidly (transmitter in blue color and receiver in green color). The pairing is processing. Once pairing is done, the transmitter status LED is now fixed blue color and receiver status LED is fixed green color.

If Transmitter or receiver looses DMX signal, the status LED will blink slowly

The EVENTPAR MINI fixture is automatically set as «Receiver» if the fixture is set in DMX mode and if no DMX signal is received by the connector «DMX IN».

The EVENTPAR MINI fixture is automatically set as «Transmitter» if it receives a DMX signal on its input «DMX IN» or if it is set up in : AUTO, COLO, STAT or SOUN mode.

ADD A FIXTURE IN AN ACTIVE GROUP

Press and hold 3 seconds on receiver button on your new fixture to reset the pairing until the status LED becomes white.(this means that receiver is now ready to be paired).
Press now on transmitter button to start pairing. Both receiver and transmitter will blink rapidly (transmitter in blue color and receiver in green color). The pairing is processing. Once paring is done, the transmitter status LED is now fixed blue color and receiver status LED is fixed green color. The other fixtures already paired in this group with this transmitter remain paired of course.

SET UP A NEW GROUP
To set up a new group is very easy. You need one more transmitter of course. Keep the existing groups active , and start the procedure above called « Pairing you DMX fixture».

NOTES
This DMX wireless system from Algam Lighting is not limited in number of groups and in number of fixtures connected in a group.

DMX PROTOCOL

4 CHANNEL

CHANNEL	VALUE	FUNCTION
CH1	R dimming	Red dimming – From dark to bright
CH2	G dimming	Green dimming – From dark to bright
CH3	B dimming	Blue dimming – From dark to bright
CH4	W dimming	White dimming – From dark to bright
CH1	Master Dimmer	RGBW master dimmer – From dark to bright
CH2	R dimming	Red dimming – From dark to bright
CH3	G dimming	Green dimming – From dark to bright
CH4	B dimming	Blue dimming – From dark to bright
CH5	W dimming	White dimming – From dark to bright
CH6	Master strobe	RGBW master strobe – From slow to fast
CH7	Function selection	0 – 50 no function

51 – 100 static colors output, controlled by CH8
101 – 150 Color jumping
151 – 200 Color Gradual change
201 – 250 Color Pulse change
251 – 255 Sound control
CH8| Function speed| Function speed from slow to fast (When color output,it is color selection )

Rated voltage: 100-240V~ – 50/60Hz
Power consumption: 32W
Light source: 4 x 10W RGBW LED
Lamp rated life: > 50000 hours
Angle du faisceau: 40°
DMX 512 channels mode: 4 or 8 channels
Dimming: 0-100%
Protection rating: IP20
Specifications: Batterie, télécommande HF, DMX sans fil intégré
Working time: 6 hours full colors, 18 hours single color
Control mode: WDMX, DMX, AUTO, SOUND, MASTER/SLAVE, STATIC COLOR
Dimensions: 130x130x122 mm
Net weight: 1.9kg

This device contains lithium-ion batteries.

The shipment of devices containing lithium-ion batteries may require marking.
Please observe national regulations.

This product is subject to the European Waste Electrical and Electronic
Equipment Directive (WEEE) in its currently valid version.

Do not dispose with your normal household waste.

Dispose of this device through an approved waste disposal arm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility

CE Icon
This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:

RED Directive 2014/53/EU

RoHS 2 Directive 2011/65/EU

The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at contact@algam.net

Tous droits réservés. Aucun extrait de ce manuel ne peut être
reproduit, sous quelque forme ou par quelque moyen que ce soit,sans
permission écrite de la société ALGAM.
ALGAM
2 Rue de Milan, 44470 Thouaré-sur-Loire, FRANCE

Symbols