algam STAGEBAR-II Light Stand Rgb Led Projector Set Instruction Manual

algam STAGEBAR-II Light Stand Rgb Led Projector Set

Thank you!

Thank you for choosing one of our Algam Lighting products. Please read this user’s manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling. Keep this user’s guide for future reference

SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols to warn of potential hazards related to the use of electrical dangers associated with the use of electrical equipment. If any of these symbols are present on your device, please read the following instructions:

ATTENTION !
Before using your equipment, we recommend that you read all the instructions in this manual.
ATTENTION !
This device produces an intense and powerful light. Risk to the eyes. Do not look directly into the beam.
DANGER !
Hazardous voltage, risk of electric shock. Do not open the product. To reduce the risk of electric shock do not expose this equipment to rain or moisture.
ATTENTION !
Risk of burns. The exterior of the unit can become very hot. Do not touch within 10 minutes of use.
ATTENTION !
Fire hazard. Keep all combustible and flammable materials away from the materials away from the unit during operation.
DANGER !
Safety hazard. This appliance presents a significant risk of injury. Follow the safety instructions.
**** Place the unit at least 50cm away from flammable materials and walls.

INSTALLATION

• Unpack and check carefully for transport damage before using the product. Never put a damaged product into operation.

• This product must be installed with strong hooks of adequate size for the weight carried. The product must be screwed
  to the hooks and tightened properly to prevent it from falling due to vibrations. Also check that the structure (or hanging
  point) can support at least 10X the weight of the hanging unit. The device must be installed by a qualified person and must
  be placed out of reach of the public. It is necessary to use a secondary hanging system (safety sling) approved for the
  weight of the device.

• This unit is intended for indoor use only. Exposing the unit to rain or moisture may result in electric shock or fire.

• Do not place the unit, speakers or any other object on top of the power cord and make sure it is not pinched.

• For proper protection against electric shock, the unit must be connected to earth (ground). The electrical supply circuit
  must be equipped with a fuse or circuit breaker and a differential protection device.

• The FLORIDA-BAR II tripod must be installed flush with the ground on a stable, level surface.

• Incorrect mounting or the use of unsuitable fastening equipment can result in an unstable and dangerous installation

• Power Disconnection Notice: To disconnect the device from the power source, the power plug must be removed from the power outlet. For this reason, the device must be placed in a position that allows constant, unobstructed access to the power outlet. This way, in case of an emergency, you can disconnect the power plug immediately.

• The unit should only be installed in a well ventilated area. Make sure that no ventilation slots are blocked. To ensure adequate ventilation, leave at least 20 cm of free air space around the sides and top of the u

USAGE

• This appliance must not be used by persons (including children) with limited physical, physiological or mental capabilities or lack of experience and/or knowledge, unless they are supervised by a person responsible for their safety or are instructed by that person in the operation of the appliance.

• Never leave this equipment unattended.

• If you experience any problems with the unit, stop using it immediately. Do not attempt to repair it yourself. Contact your dealer or an authorized service center. There are no user replaceable parts.
  • NEVER use the unit under the following conditions:

  In areas subject to vibration or bumps,
  In places where the ambient temperature is above 45 ° C or below 2 ° C.
  In areas exposed to excessive dryness or humidity (ideal conditions: between 35% and 80%).

• Never use the unit near flames, flammable or explosive materials or hot surfaces. Doing so may cause a fire. • The exterior of the unit can become very hot. It is important to avoid contact with the unit during operation and for at least 10 minutes after use.

• It is important to use the supplied power cable (grounded cable).

• Before turning on the power, make sure that the voltage and frequency of the power supply match the power requirements of the unit, as described in this manual.

• Never cut or tamper with the power cord or plug. If a power cord is provided with a ground wire, it is required for safe operation! Risk of fatal electric shock!

• Always hold the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this may cause a short circuit or electric shock.

• Do not connect this device to a dimmer pack

• DO NOT allow liquids or objects to enter the unit. If liquid is spilled on the unit, immediately UNPLUG the power supply to the unit and contact customer service.

• You must ensure that the power cord never gets wet during operation. Before a thunderstorm and/or a lightning storm, unplug the unit from the mains.

• Under no circumstances should you open the housing of the device. If you do, your safety will not be assured. There are no operational components inside, only dangerous voltages that can give you a fatal shock!

MAINTENANCE / SERVICE

• Never attempt to disassemble, repair or modify the unit yourself. Otherwise, the warranty becomes void. Repairs by
  unqualified persons may result in damage or malfunction. Please contact the nearest authorized service center. The light
  source contained in this fixture should only be replaced by the manufacturer or its service agent or a person of equivalent
  qualification.

• Screens, lenses or UV filters should be replaced if they are visibly damaged to an extent that compromises their effectiveness, such as by deep cracks or scratches.

• The lamp should be replaced if it has been damaged or deformed by heat.

• Disconnect the unit from the mains before servicing.

• If the cable or flexible outer cord of this fixture is damaged, it must be replaced with a special cable or cord from the
  manufacturer or its service agent only.

• Never immerse the unit in water or any other liquid. Wipe only with a slightly damp cloth.

• CAUTION : To reduce the risk of fire replace fuse with same type and rating

PRODUCT INSTALLATION

POWER SUPPLY
Please use the attached power, note that power voltage and frequency are the same as the marked voltage and frequency of device when connecting power. Every device’s power should be connected separately, so that device can be controlled individually

CABLE SPEC.

CABLE SPEC.|
---|---
CABLE (EU)| CABLE (US)| PIN| INTERNATIONAL
Brown| Black| Live| L
Light Blue| White| Neutral| N
Yellow/Green| Yellow/Green| Earth|

DMX CONNECTION
Connection between laser lights and DMX must use the shied cable of diameter more than 0.5mm. Please use the attached 3 pin XL plug/socket to connect the DMX output/input interface. The connection between socket and cable as below (note the plug/socket’s 3 pin number and position

DMX-OUTPUT
XLR mounting-sockets (rear view)

DMX-INTPUT
XLR mounting-plugs (rear view)

When using standard DMX512 control signal, the last device’s output interface must be connected to a DMX plug.
This plug is putting a 120 ohm resistance between “canon” plug’s 2 pin and 3 pin. Showing as below pic. Sticking this plug into the last device’s signal output interface, it will avoid the interference during the process of signal transmission.

RIGGING

Attention! The installation must be carried out by qualifi ed service personal only. Improper installation can result in serious injuries and /or damage to property. Overhead rigging required extensive experience! Working load limits should be respected, Certifi ed installation materials should be used, the installed device should be inspected regularly for safety

OPERATION INSTRUCTIONS

| FUNCTION| DESCRIPTION
---|---|---
1| DMX input/output| 3PIN male/female XLR interface, for DMX communication
2| Power connection| Power output connect with next light
3| Power input| Power input socket, built-in protective tube and spare tube
4| Microphone| Receiving the audio signal through a microphone, and positive response to the intensity by the potentio
5| Potentiometer| To adjust the soung activated
6| LCD control interface| Various mode setting operations of the machine
7| LED strobe lights| 4 x 1W white LED strobe lights
8| LED PAR lights| 12xTri-9W

| FUNCTION| DESCRIPTION
---|---|---
1| MENU| To go forward in the selected functions or go back the last layer menu
2| | To go forward in the selected functions or increase parameter
3|  | To go backward in the selected functions or reduce parameters
4| ENTER| To go into the next layer menu

1. Press ENTER to save any operation, or will return to last menu in 10 seconds.
2. Touch Menu , and power on to restore factory setting.

mode)
| | Signal reception mode (the worlds will strobe if there’s ni signal)
| DMX channel selecting
| Channel adress setting
| | Slave mode
| Adress setting
| | Be the master for synchronous mode (under AUTO/SOUND/COLOR mode)
| Wireless pedal working mode
| Aging testing and main board testing program
| Restore the factory initial setup

FOOTSWITCH OPERATION INSTRUCTION

| FUNCTION| DESCRIPTION
---|---|---
1| AUTO| Press MUSIC to activate the sound program controls. When working, all the lights will begin in sound mode
2| MUSIC| Press MUSIC to activate the sound program controls. When working, all the lights will begin in sound mode
3| COLOR| Color setting : R-G-RG-B-RB-GB-RGB
4| BLACKOUT| Light off

All the operations from the footswitch is invalid to the DMX mode and the SLAVE mode.

DMX PROTOCOL

3 CHANNELS|
---|---
CHANNEL| VALUE| DESCRITPION
| 000 – 009| Blackout
| 010 – 050| Auto PAR show
| 051 – 090| Auto LED FLASH show
CH1| 091 – 130| MIX auto show
| 131 – 170| Sound PAR show
| 171 – 210| Sound LED FLASH show
| 211 – 255| MIX sound show
CHANNEL| FUNCTION| VALUE| DESCRITPION
---|---|---|---
Aut CH2o PAR show| 000 – 014| Auto PAR 01
015 – 029| Auto PAR 03
030 – 044| Auto PAR 03
045 – 059| Auto PAR 04
060 – 074| Auto PAR 05
075 – 089| Auto PAR 06
090 – 104| Auto PAR 07
105 – 119| Auto PAR 08
120 – 134| Auto PAR 09
135 – 149| Auto PAR 10
150 – 164| Auto PAR 11
165 – 179| Auto PAR 12
180 – 194| Auto PAR 13
195 – 209| Auto PAR 14
210 – 224| Auto PAR 15
210 – 224| Auto PAR 16
240 – 255| Auto PAR 17
Auto LED FLASH show| 000 – 024| Auto LED 01
025 – 049| Auto LED 04
050 – 074| Auto LED 04
075 – 099| Auto LED 04
075 – 099| Auto LED 05
075 – 099| Auto LED 06
075 – 099| Auto LED 07
175 – 199| Auto LED 08
200 – 224| Auto LED 09
225 – 255| Auto LED 10

3 CHANNELS

5 CHANNELS

24 CHANNELS

SPECIFICATIONS

This product is subject to the European Waste Electrical and Electronic Equipment Directive (WEEE) in its currently valid version.
Do not dispose with your normal household waste.
Dispose of this device through an approved waste disposal arm or through your local waste facility. When discarding the device, comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility

This Algam Lighting product is compliant to all required UE certifications and conformed to following standard and UE directives:
LVD Directive 2014/35/EU :
EMC Directive 2014/30/EU :
RoHS 2 Directive 2011/65/EU
The UE DECLARATION OF CONFORMITY is available, if you need it, please just ask for it at : contact@algam.net

Tous droits réservés. Aucun extrait de ce manuel ne peut être reproduit, sous quelque forme ou par quelque moyen que ce soit,sans permission écrite de la société ALGA
ALGAM 2 Rue de Milan, 44470 Thouaré-sur-Loire, FRANC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>