ATOMSTACK F03-0107-0AA1 MAKER AC1 Camera for Laser Engraver User Manual
- June 13, 2024
- ATOMSTACK
Table of Contents
F03-0107-0AA1 MAKER AC1 Camera for Laser Engraver
User Manual http://qr71.cn/oIsRvn/qodW6yZ
Declaration
ATOMSTACK MAKER AC1 camera functions need to be controlled by Light Burn, please download the official version of Light Burn software. Lightbar is a third-party software, so ATOMSTACK service is not responsible for any loss caused by the operation of Light Burn, the firmware of ATOMSTACK has been tested in detail by ATOMSTACK, and the situation of incompatibility with software or hardware is still possible occur. If an error occurs due to incompatibility, you can contact our customer department service for technical support. support@atomstack.com
Precautions
- Do not collide or move the camera during the calibration process.
- Do not collide or move the camera after the alignment of the calibration camera is completed. If the camera is collided and the camera is shifted left and right, the camera lens and camera alignment need to be recalibrated.
- Cardboard and dot cards need to be flat.
Assembly steps
Preparation
(installation and debugging)
4.1 Place the 100mm100mm cardboard flatly in the working area of the
engraving machine, fix the focus, and then return the laser to the origin of
the machine to engrave a pattern of 400400mm.
4.2 Fix the assembled camera on the machine (Picture
1), Pay attention to keep the position of the machine and the paper unchanged;
adjust the position of the camera so that the distance between the working
plane and the camera lens is 420mm (Picture 2), and make the center of the
camera lens align with the cross position as much as possible (Picture
3).!ATOMSTACK F03-0107-0AA1 MAKER AC1 Camera for Laser Engraver -
Preparation 1
Calibrate Camera Lens
5.1 Check camera control in the Window drop-down menu 5.2 Select the camera in
the camera control window. 5.3 Right-click in the camera control window and
click Calibrate Camera Lens. 5.4 Click Update Overlay, select the Camera name,
Standard Lens, and None – do full calibration in the pop-up window.
5.5 Click to close Honeycomb check enabled. 5.6 Observe
whether the fixed focus plate in the preview window is tilted or not. If it is
tilted, adjust the knob to fine-tune the camera lens so that the cross mark is
in the center of the field of view, and the top, bottom, left, and right are
as
symmetrical as possible. 
5.7 Place the dot card in five positions, left, right,
top, bottom, and middle, and capture 5 times. If the captured result Score≤1
and the pattern is slightly deformed or not deformed, click Next; if the
pattern cannot be captured, repeat step 2 Fine-tune the lens or move the
position of the dot card to capture again (the recommended order of dot card
placement is left, right, top, bottom, and middle) until the capture is
successfully completed.
Calibration Camera Alignment
6.1 Take away the fixed focus card, click on the “Camera Alignment” window, if
this interface is closed, please click “Camera Control” -> “Camera Alignment”
-> “Camera” -> Next
6.2 Set the engraving parameters (refer to the
laser parameter table), and set the Scale value according to the actual
positioning size, see the table below
| Scale | Sizemm^2 |
|---|---|
| 100 | 200*200 |
| 150 | 300*300 |
| 200 | 400*400 |
6.3 Click Frame to see if there is a collision, if there is a collision, you
need to set a smaller Scale value, or recalibrate the camera
6.4 Click Start
and make a positioning mark
6.5 After the engraving is complete, click the
button in the red box to move the laser to the upper position so as not to
block the engraved pattern, click Capture Image, and then click
Next.
6.6 First zoom in on
the pattern at position 1, double-click the cross point, and click the cross
point position in the order of numbers 1-4. If the double-clicked cross has
obvious deviation, you can click Undo Last or a blank position, and then
double-click to re-select the cross point. 
6.7 Remove the cardboard when finished and click
Update Overlay
How to use positioning
7.1 Place the engraving or cutting material within the engraving range, and
fix the focus, click “Home” to return the laser to the machine origin, click
Update Overlay, and move the engraving pattern to the position you want to
engrave.
7.2 Set the parameters of engraving and click
start
7.3 The engraving is
completed, the effect is shown below
How to record video
8.1 Select None in the camera control to turn off the camera
8.2 Windows system, turn on the camera, it is
recommended to select low resolution when recording video, so as not to occupy
too much memory
8.3 The Windows system uses its
own camera to record videos within 3H. If it exceeds 3H, it is recommended to
download free video recording software, such as PotPlayer. It is recommended
to use Camera Record-Video Recorder and Quick Player for macOS system.
FAQ
1. How to deal with the edge collision in Step 6.3 calibration camera alignment?
Check whether there is a phenomenon that the captured image is severely deformed and you continue to click Next during the process of calibrating the camera lens. If yes, please recalibrate the camera lens.
2. How to deal with the positioning accuracy error > 2mm?
- During the process of calibrating the camera lens, whether there is a phenomenon that the captured image is seriously deformed and you continue to click Next? If yes, please recalibrate the camera lens. 2) After the calibration of camera alignment is completed, whether there is a collision or the camera is moved, if the camera is collided and the camera is displaced left and right, please recalibrate the camera lens and the camera alignment.
3.Does it need to be recalibrated when changing the material to be tested, removing or adding honeycomb panels?
The height range between the camera and the measured object can be between 400-440mm, and no recalibration is required for changing the tested material, removing or adding honeycomb panels.
Customer service:
For detailed warranty policy, please visit our official website:
www.atomstack.com
For technical support and service, please email
support@atomstack.com
Manufacturer:
Shenzhen AtomStack Technologies Co.,Ltd
Address: 17th Floor, Building 3A, Phase II, Intelligent Park, No. 76,
Baohe Avenue,
Biolung Street, Longing District, Shenzhen, Guangdong, China
Zip code: 518172
Scan QR code: QR code reader/barcode scanner or any app with a scanner
Documents / Resources
|
ATOMSTACK F03-0107-0AA1 MAKER AC1 Camera for Laser
Engraver
[pdf] User Manual
F03-0107-0AA1 MAKER AC1 Camera for Laser Engraver, F03-0107-0AA1, MAKER AC1
Camera for Laser Engraver, Camera for Laser Engraver, for Laser Engraver,
Laser Engraver
---|---
|
ATOMSTACK F03-0107-0AA1 MAKER AC1 Camera for Laser
Engraver
[pdf] User Manual
F03-0107-0AA1 MAKER AC1 Camera for Laser Engraver, F03-0107-0AA1, MAKER AC1
Camera for Laser Engraver, Camera for Laser Engraver, Laser Engraver, Engraver
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>