ATOMSTACK M100 130W Quad-Laser Module With Air Assist System Instruction Manual

ATOMSTACK M100 130W Quad-Laser Module With Air Assist System

Security statement and warning

1. This product is a laser engraver system component, that must be installed in other manufacturers of laser engravers for use.And the product belongs to Class 4 laser products, the laser system itself must meet the requirements of IEC 60825-1 latest version, otherwise, the product is prohibited to be used.

2. Your laser engraver shall have a protective housing which, when in place, prevents human access to laser radiation.

3. If protective housing is equipped with an access panel that provides “walk-in” access then:

   • means shall be provided so that any person inside the protective housing can prevent activation of a laser hazard that is equivalent to Class 3B or Class 4.
   • a warning device shall be situated so as to provide adequate warning of emission of laser radiation equivalent to Class 3R in the wavelength range below 400 nm and above 700 nm, or of laser radiation equivalent to Class 3B or Class 4 to any person who might be within the protective housing.
   • where “walk-in” access during operation is intended or reasonably foreseeable, emission of laser radiation that is equivalent to Class 3B or Class 4 while someone is present inside the protective housing of Class 1, Class 2, or Class 3R product shall be prevented by engineering means.
     NOTE Methods to prevent human access to radiation when persons are inside the protective housing can include pressure-sensitive floor mats, infrared detectors, etc.

4. The laser itself has a protective cover, the protective cover is fastened by screws. When the laser is installed on the laser engraver, the protective cover should be checked to be reliably locked, and can not be removed in the energized state.

5. The housing of the laser engraver should have an interlock function. When the housing is opened or removed, the laser can be automatically turned off.

6. The laser engraver should have an emergency stop button, which can immediately stop the output of the laser when pressed under unexpected circumstances.

7. The laser engraver should have a reset button, which can resume work under the condition of confirming safety after lifting the interlock or emergency stop.

8. Laser engravers should use physical keys, dongles, password systems and other ways to manage and control, to prevent personnel without security training operating of this kind of equipment.

9. On the laser engraver any window or channel that can actively observe or passively receive the laser radiation should be set up warning marks.

10. If the laser burns the skin or eyes, please go to a nearby hospital for examination and treatment immediately.

Disclaimer and warning

This product is not a toy and is not suitable for people under 15 years of age. Do not allow children to touch the laser Module. Please be careful when operating in scenes with children. This product is a laser module, visit http://www.atomstack3d.com/laserengraverdownload for a complete “user manual” and the latest instructions and warnings. Shenzhen AtomStack Technologies Co., Ltd. (Atomstack) reserves the right to update this Disclaimer an d Safe Operation Guidelines.
Please be sure to read this document carefully before using the product to understand your legal rights, responsibilities and safety instructions; Otherwise, it may bring property loss, safety accidents,s and hidden dangers of personal safety. Once you use this product, you shall be deemed to have understood, accepted and accepted all terms and contents of this document. The user undertakes to be responsible for his or her actions and all consequences arising therefrom. User agrees to use the Product only for legitimate purposes and agrees to the entire terms and contents of this document and any relevant policies or guidelines that AtomStack may establish. You understand and agree that AtomStack may not be able to provide you with the cause of the damage or accident and provide you with AtomStack’s after-sale service unless you provide the original engraving or cutting files, engraving software configuration parameters used, operating system information, video of the engraving or cutting process, and operational steps prior to the occurrence of a problem or failure. AtomStack is not liable for any and all losses arising from the user’s failure to use the product in accordance with this manual. Atomstack has the ultimate right to interpret the document, subject to legal compliance. Atomstack reserves the right to update, modify or terminate the Terms without prior notice.

Accessories list

Function description of the adapter board

If your laser is in the form of the picture below, please follow the steps below to install the combination slider

Installation Steps

1. Remove the original laser fixing plate and lase
2. Find this combination slide in accessories
3. Fixed combinationslider
4. Fixed combination slider
5. Install the laser
6. Install theair pipe

If your laser is in the form of the picture below, please follow the steps below to install the slider

installation step

1. Remove the original laser rail and laser
2. Find the slide rail that fits the model in the accessories
3. Fixed slider
4. Laser installation
5. Assemble the trachea

How to connect the power adapter

The voltage of the M100 module is DC24V, the following models need to add a power adapter board to use. A5 10W; A5 20W; A5 30W; A5 PRO; A5 PRO+ ;A5 M30; A5 M40

The user’s original adapter is connected to the one-to-two transfer cable, and one end of the one-to-two transfer cable is connected to the air pump; the other end is connected to the control box. The 24V adapter in the M100 module is connected to the “POWER” position on the adapter board. The 3PIN cable of the engraving machine originally connected to the laser is now connected to the adapter board “Input c”. Find the laser adapter cable from the accessories, connect one end of the 3PIN to the adapter board “Output”, and connect the 4PIN end of the laser adapter cable to the M100 module

A5 M50; A5 M50 PRO; X7; X7 PRO; A10; A10 PRO; S10 PRO The connection method of the power adapter of these models

The user’s original laser engraving machine adapter is connected to the air pump; the DC24V adapter equipped with the M100 module is connected to the control box. The control box can be compatible with DC24V

Precautions:
The 20W module is relatively heavy, in order to make the machine work without shaking and work more stably. We added a screw on the laser to limit the laser to work as close to the height of the POM wheel as possible. Can be removed if not needed

A lot of smoke is generated in engraving or cutting wood and other objects, be aware of cleaning the air guide hood and anti-skid cover, since there may be a lot of dust accumulation on it, especially working with more than 50% of the laser power. Remove the shield if you could, or turn on the air assit while the machine working, all of which would significantly reduce dust accumulation.

warning

The laser power of this machine is very high, if you need to cut wood and other flammable materials with a power of more than 70%, please ensure someone is watching the machine in case of the flammable materials catch fire.

Cautions LASERBEAMC AND AMAGE EYES

Laser Light can damage the human eyes and skin. Do not expose the eye or skin to laser light directly. This Laser product has an optical lens and emits a collimated laser beam. The light from this product, both direct and reflected, is very harmful as it can propagate a long distance while maintaining high optical density. When handling the product, wear appropriate safety glasses (OD5+) to protect your eyes from laser light including reflected and stray light. The reflected and stray light spilling into an unintended area should be attenuated and/or absorbed.

Maintenance instructions and warning

This product uses a highly integrated design and requires no maintenance. However, if the laser system installed with this product needs to be repaired or tuned, please:

1. Unplug the power cord on the laser, so that the laser is in a state of power failure;
2. If you need laser assistance for tuning, please:
   • All present personnel wear protective glasses, OD5+ protective glass is needed ;
   • Make sure there are no flammable or explosive materials around;
   • The position and direction of the laser are fixed to ensure that the laser will not accidentally move and shine on people, animals, flammable, explosive, and other dangerous and valuable objects during debugging.
   • Don’t look at lasers
   • Do not shine the laser on the mirror object, lest the laser reflection cause accidental injury

Customer Service:

• For a detailed warranty policy, please visit our official website at: www.atomstack.com
• For technical support and service, please email: support@atomstack.com

Manufacturer: Shenzhen AtomStack Technologies Co., Ltd. Address: 17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Baolong Street, Longgang Dist., Shenzhen, 518172, China

Scanner APPLICATION:

QR code reader/ Barcode scanner or any APPwithscanner.

References

• AtomStack Official Website | Unleash Your Creativity With Laser

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>