rocstor Y10E028-B1 SolidRack Wall Mount Rack 2-Post Open Frame Adjustable Depth User Manual
- June 13, 2024
- rocstor
Table of Contents
Y10E028-B1 Solid Rack Wall Mount
Rack 2-Post Open Frame Adjustable Depth
User Manual
Solid Rack Wall Mount Rack 2-Post Open Frame
Adjustable Depth
Rocstor Legal Disclaimer
The information presented in this manual is not warranted by Rocstor to be
totally authoritative, error free, or complete. This publication is not meant
to be a substitute for a detailed operational and a site-specific development
plan for the use of the product. Therefore, Rocstor assumes no liability for
damages, violations of codes, improper installation, system failures, or any
other problems that could arise based on the use of this Manual.
THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE LIMITED IN TIME TO THE DURATION
OF THE WARRANTY AS STATED HEREIN AND IS EXCLUSIVE IN LIEU OF ALL OTHER
WARRANTIES, LEGAL THEORIES, REMEDIES AND CONDITIONS, WHETHER ORAL OR WRITTEN,
EXPRESS OR IMPLIED. IN NO EVENT SHALL ROCSTOR, OR ANY PARENT, AFFILIATE OR
SUBSIDIARY COMPANY OF ROCSTOR OR THEIR RESPECTIVE OFFICERS, DIRECTORS, OR
EMPLOYEES BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE,
SPECIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, DAMAGES FOR
LOSS OF BUSINESS, CONTRACTS, REVENUE, LOST PROFITS, DATA, INFORMATION,
GOODWILL OR BUSINESS INTERRUPTION RESULTING FROM OR ARISING OUT OF THE USE OF
THE PRODUCT OR FAILURE TO FOLLOW INSTRUCTIONS IN THE MANUAL.
FURTHERMORE, ROCSTOR SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IF
ROCSTOR CANNOT LAWFULLY DISCLAIM SUCH IMPLIED WARRANTIES, THOSE IMPLIED
WARRANTIES WILL BE LIMITED IN DURATION TO THE DURATION SET FORTH ABOVE.
FURTHER STILL, ROCSTOR RESERVES THE RIGHT TO MAKE CHANGES OR UPDATES WITH
RESPECT TO THE CONTENT OF THE PUBLICATION OR THE FORMAT THEREOF AT ANY TIME
AFTER PURCHASE WITHOUT
NOTICE.
Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages or exclusions or limitations on the
duration of implied warranties or conditions, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal
rights and you may also have other rights that vary by state or province.
Copyright, intellectual, and all other proprietary rights in the content of
the manual (including but not limited to software, audio, video, text, and
photographs) rests with Rocstor or its licensor. All rights in the content are
the property of Rocstor and are not granted, licensed, assigned or otherwise
passed to the purchaser’ of the product or to persons having access to the
information in the manual PHILLIPS® is a registered trademark of Phillips
Screw Company in the United States or other countries.
Important Safety Information
Please review and read the instructions very carefully in order to understand
the specification of the equipment. This is essential information before
installing, operating, service or maintaining your equipment. These messages
or alerts may appear throughout this publication and manual for your
purchased equipment. The messages are designed to warn you of possible hazards
or to bring to your attention the information that would assist and clarifies
steps and procedures.
This symbol and label provides Danger or Warning safety which indicates an
electrical hazard exists. If instructions are not fully followed, it may
result in personal injury.
This is a safety alert symbol. It is used to alert you to potential personal
injury hazards. Please follow the instructions very carefully and obey all
safety messages that follow this symbol to avoid possible injury or death.
DANGER
DANGER This symbol represents an imminently hazardous situation which, if
not avoided, will result in death or serious injury. Please follow
instructions carefully.
WARNING
WARNING This symbol represents a potentially hazardous situation which,
if not avoided, can result in death or serious injury. Please follow
instructions carefully.
CAUTION
CAUTION This symbol indicates a potentially hazardous situation which, if
not avoided, can result in minor or moderate injury.
CAUTION
CAUTION, This symbol is used without the safety alert symbol, indicates a
potentially hazardous situation which, if not avoided, can result in equipment
damage. Please follow instructions carefully. Please follow instructions
carefully.
NOTICE
NOTICE This symbol provides information’s and practices not related to
physical injury including certain environmental hazards, potential damage or
loss of data. Please follow instructions carefully.
Safety Instructions
Please follow the essential and important instructions in this manual. The information provides you useful instructions for installation and customization of the rack or equipment.
WARNING
TIP/ HEAVY EQUIPMENT HAZARD
- The content of this packaging is easily tipped. Please be extra careful and use extreme caution when moving or unpacking this cabinet.
- Two people are preferred and are required to move, unpack and install the cabinet.
- Not following these instructions carefully, can result in death, serious injury, or equipment damage. Please follow the assembly instructions very carefully.
- This cabinet enclosure has 85 lb (38.5 kgs) Maximum Load Capacity. Please do not exceed the weight capacity limit of this product. Overloading the capacity of this product may result in bodily and property damage.
- This product is designed for indoor use. Do not use outdoors or in an open area. • DO NOT push the rack from its sides.
- This enclosure is not designed to be stacked. Do not place any items or liquids on top or around the enclosure.
- It is important to survey the area that this rack will be installed to assure the area is able to handle the total weight of the cabinet and the equipment inside the rack after all equipment installation.
Warning:
Do not attempt to mount to wall, when equipment is mounted inside rack.
Rack can hold up to 85 pounds evenly distributed. Make sure wall surface can
hold weight of rack/equipment.
Not following these instructions carefully, it can result in death, serious
injury, or equipment damage
Introduction
Solid Rack Wall Mount Rack – 2-Post Open Frame – Adjustable Depth 18-28″ – Weight Capacity 85 lb (38.5kg) – For Audio/Video, Server Room, Switches & Routers, Computer Equipment – With M6 screws/cage nuts – 19in Width Compatible – Wall mount network rack Cabinet – Cold-rolled Steel CRS – EIA/ECA-310 compatible – Black
Component Identification
Parts List
| |
---|---|---
| | 
Hardware and Accessories
| |
---|---|---
To ensure proper and secure installation, cage nuts need to be installed horizontally as shown below. Installing cage nuts in the incorrect orientation can cause injury or equipment damage.
Assemble the Rack
-
Start by placing both Side Brackets (1) parallel to each other.
-
Find your required server or networking equipment depth, and then adjust depth of the rack and mount top and bottom brackets. Then secure the top and bottom brackets (2) to the side brackets (1). Use the included 12x M6 screws and nuts.
(Please use 3 screws and 3 nuts for each of the four sides, like seen above)
-
Place and attach Mounting Section (3) to the top and bottom brackets (2). Once the Mounting Section (3) is placed to the front opening of the frame, then pull back the metal pins which are located on the inside bottom of the mounting section (3). At this time align the mounting section to the frame opening of the bracket, then release the metal pins which are located on all four corners of the bracket. Release the pins into the holes on the top and bottom brackets (2). At this time your installation is now complete and your IT server or equipment are ready to be installed.
Enclosure Installation
CAUTION
CAUTION, This symbol is used without the safety alert symbol, indicates a
potentially hazardous situation which, if not avoided, can result in equipment
damage. Please follow instructions carefully. Please follow instructions
carefully.
NOTICE
NOTICE This symbol provides information’s and practices not related to
physical injury including certain environmental hazards, potential damage or
loss of data. Please follow instructions carefully.
Tools Requirement & Preparation for Installation
Make sure you inspect the area that this racks will be installed. This
enclosure should be installed in a structurally sound area that can handle the
load and the weight of the racks. If you place the enclosure on a level floor,
make sure the floor can bear the weight of the enclosure, all equipment that
will be installed in the enclosure. For permanent wall mount installation,
make sure to securely fasten the enclosure to the building structure.
The following tools are required for proper installation:
- Level (not included)
- Phillips-head screwdriver (not included)
- Appropriate tools for wall mounting (not included)
- Appropriate hardware for wall mounting (not included)
Five-Year Factory Warranty
Rocstor provides a Limited Factory Warranty which applies to products you have
purchased for commercial or industrial use in the ordinary course of your
business.
Terms of warranty
Rocstor warrants its Solid Rack product series to be free from defects in
materials and workmanship for a period of five years from the date of
purchase. Rockstar’s obligation under this warranty coverage is limited to
repairing or replacing, at its sole discretion, any such defective products.
This warranty does not apply to equipment that has been damaged by accident,
negligence, or misapplication or has been altered or modified in any way. In
the event Rocstor repairs or provide a replacement of a defective product or
part, the warranty does not extend the original warranty period. Rocstor
reserves the right to repair or replace any parts under warranty as new or
factory re manufactured.
Non-transferable warranty
This warranty extends only to the original purchaser who must have properly
registered the product.
The product may be registered at the Rocstor Web site, https://rocstor.com
/customer-support/warranty registration.
Exclusions
If Rocstor tests or examines the alleged defect in the product and finds that
the damages or defects do not exist or were caused by a third party or an end
user’s misuse, improper installation or testing, or negligence, then Rocstor
shall not be liable under the warranty. Furthermore, unauthorized attempts to
repair or modify the product by wrong or inadequate electrical connection or
voltage, inadequate or inappropriate site operation conditions, repair,
installation corrosive area or atmosphere, a change in location or operating
conditions or use, repair by non-Rocstor designated personnel, exposure to the
elements, fire, Acts of God, theft, or equipment installation not recommended
or contrary to Rockstar’s specifications or recommendations. Warranties will
be void and Rocstor will not be liable if the product serial number is
tampered with, altered, removed, defaced or any other cause beyond the range
of intended use.
Contact Information
Corporate Headquarters
12979 Arroyo Ave
San Fernando, CA 91340 – USA
Office: +1 818-727-7000
Fax: +1 818-875-0002
Email: info@Rocstor.com
Technical Support / RMA
Hours: 9:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
Tell: +1 818-727-7000 (Domestic and
Internationals)
Fax: +1 818-875-0002
Email: support@Rocstor.com
Sales Info
Hours: 8:00 am – 5:00 pm PST
Mon – Fri (excluding holidays)
Tell: +1 818-727-7000 (Domestic and
Internationals)
Fax: +1 818-875-0002
Email: support@Rocstor.com
Corporate, Government and Academic Customers
Our Corporate Sales Team’s goal is to help our U.S.A. and Canadian customers
find a storage solution that best serves their needs. We will help you
determine your best purchasing options. For more information please contact
the appropriate department below or call us at +1
818-727-7000.
General sales information: sales@Rocstor.com
Corporate sales information:
corporate_sales@Rocstor.com
Educational sales information:
academic_sales@Rocstor.com
Federal, State & Local government sales information:
government_sales@Rocstor.com
Resellers/Business Development/OEM Partners
All Channel National and International Resellers, VARs, Consultants …
contact Rocstor Channel Sales:
call: +1 818-727-7000
Email: reseller_info@Rocstor.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>