MYSON PUMV011 Unisenza Plus Electronic Thermostatic Head User Guide

MYSON PUMV011 Unisenza Plus Electronic Thermostatic Head

Product Information

The Unisenza Plus Electronic Thermostatic Head is a device that allows for precise control of temperature in your home. It can be easily installed on standard valves or Danfoss RA valves. The pack contents include the electronic thermostatic head, 2 x AA-sized alkaline batteries, and an RA adaptor.

Overview

• 1. Display LCD: Shows the current temperature and other information.
• 2. Button: Used for various operations and mode changes.
• 3. Button: Used for various operations and mode changes.
• 4. Button: Used for various operations and mode changes.
• 5. Battery compartment: Holds the 2 x AA-sized alkaline batteries.
• 6. Securing ring: Used to secure the thermostatic head on the valve.

Display Icons

• Antenna: Indicates the pairing status with the Unisenza Plus Network.
• Heating On: Indicates that the device is demanding heat and the valve is open.
• Schedule mode: Indicates that the device is operating according to the schedule defined in the app.
• Off mode: Indicates that the device is turned off with frost protection active.
• Battery icon: Shows the battery level.
• Digits: Displays the set point or other information.
• Key lock: Indicates that the key is locked.
• Alert: Indicates a system fault with an error code.
• Temperature unit: Indicates the temperature unit in Celsius or Fahrenheit.

Product Usage Instructions

Installing the Battery
To install the batteries, follow these steps:

1. Open the battery compartment located on the thermostatic head.
2. Insert 2 x AA-sized alkaline batteries, ensuring correct polarity.
3. Close the battery compartment securely.

Installation of Standard Valve

To install the thermostatic head on a standard valve, follow these steps:

1. Remove the old thermostatic head (if present) from the valve.
2. Place the Unisenza Plus Electronic Thermostatic Head on the valve.
3. Secure the thermostatic head using the provided securing ring.

Installation on Danfoss RA Valve

To install the thermostatic head on a Danfoss RA valve, follow these steps:

1. Remove the old thermostatic head (if present) from the Danfoss RA valve.
2. Attach the provided RA adaptor to the valve.
3. Place the Unisenza Plus Electronic Thermostatic Head on the RA adaptor.
4. Secure the thermostatic head using the provided securing ring.

Joining Unisenza Plus Network

To join the thermostatic head to the Unisenza Plus Network, follow the appropriate steps below:

Joining Unisenza Plus Gateway without APP

1. Ensure that the Unisenza Plus Gateway is powered up.
2. Press and hold the UP button on the thermostatic head for 3 seconds.
3. Wait for the thermostatic head to pair with the Unisenza Plus Gateway.

Joining Unisenza Plus Gateway with APP

1. Ensure that the Unisenza Plus Gateway is powered up and connected to the internet.
2. Follow the instructions provided in the Unisenza Plus Gateway Instruction Manual to join the thermostatic head to the network using the app.

Changing Operation Mode

To change the operation mode of the thermostatic head, follow these steps:

1. Press the button on the thermostatic head to enter the mode change.
2. The LCD will display and flash the available modes.
3. Press the button to select the desired mode.

Note: The available modes are Schedule mode, Off mode, and Manual mode. The device operates according to the selected mode.

Pack contents

• a. Electronic Thermostatic Head
• b. 2 x AA-sized Alkaline Batteries
• c. RA adaptor

Overview

1. Display LCD
2. Button
3. Button
4. Button
5. Battery compartment
6. Securing ring

Display icons

Installation

USE

Change operation mode

Press to change one of the following operation mode. During mode change, the LCD displays and flashes the mode indication.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>