MYSON T6 IVC Radiator User Manual
- June 10, 2024
- MYSON
Table of Contents
MYSON T6 IVC Radiator
T6 IVC Radiators
The T6 IVC Radiator is a center-connection radiator that features innovative design, high-quality workmanship, and high heat output. This dual panel, double convector radiator offers the advantage of a standard 2 central connection and the standard 4 corner connection options. Pre-planning and installation are greatly reduced, saving time and money. The new T design allows installers the flexibility to connect to the most convenient location for installation.
The Myson T6 Radiator comes ready-to-install with a wall-mounting bracket set, a thermostatic valve insert, drain-off plug, air bleed vent, and compression fittings for 1/2 copper tubing. Compression fittings for 1/2 pex are available as a substitute. Herz TRV Head is available as an option.
Swapping the right-hand side built-in valve to the left-hand side is no problem at all at any time. Radiators are delivered with protective caps. After removing the protective cap (pos. A) the following thermostat heads can be fitted directly to the built-in valve (pos. B): RA 2000, RAW by Danfoss, VK by Heimeier, D by Herz, thera DA by MNG and UNI XD by Oventrop.
Usage Instructions
- Remove the protective cap (pos. A) from the radiator.
- Select one of the following thermostat heads: RA 2000, RAW by Danfoss, VK by Heimeier, D by Herz, thera DA by MNG and UNI XD by Oventrop.
- Fit the selected thermostat head directly to the built-in valve (pos. B).
- Mount the radiator on the wall using the wall-mounting bracket set.
- Connect the compression fittings to 1/2 copper tubing or 1/2 pex (if available as a substitute).
- Install the thermostatic valve insert and air bleed vent.
- Open the water supply and check for any leaks.
The T6 IVC Radiator is available in various sizes and weights:
Nominal Height (in)| Nominal Length (in)| Output (Btu/hr)| Order Code| Water
Content (gals)| Weight (lbs)
---|---|---|---|---|---
23 5/8| 28 9/10| 2890| TK2-3-06| 0.56| 31.7
11-13/16| 39 3/8| 4814| TK2-3-10| 0.90| 51.2
55 1/8| –| 6742| TK2-3-14| 1.27| 70.7
78 3/4| –| 9632| TK2-3-20| 1.64| 100.0
23 5/8| 42 1/7| 4217| TK2-5-06| 0.85| 53.5
36 1/4| –| 6466| TK2-5-92| 1.30| 81.3
19-11/16| 47 1/4| 8434| TK2-5-12| 1.65| 105.5
63| –| 11246| TK2-5-16| 2.21| 140.2
70 7/8| –| 12652| TK2-5-18| 2.49| 157.6
78 3/4| –| 14057| TK2-5-20| 2.77| 174.9
23 5/8| 48 1/11| 4811| TK2-6-06| 1.01| 64.5
36 1/4| –| 7377| TK2-6-92| 1.55| 98.3
23-5/8| 47 1/4| 9622| TK2-6-12| 1.98| 128.0
63| –| 12829| TK2-6-16| 2.65| 170.6
70 7/8| –| 14433| TK2-6-18| 2.99| 191.5
78 3/4| –| 16036| TK2-6-20| 3.33| 212.6
The radiator comes with copper compression fittings unless otherwise specified. The pressure loss graphs, conversion factors, and wall rail details are also provided in the user manual for reference.
T6 IVC Radiators
The center-connection Radiator features innovative design, high quality workmanship, and high heat output.This dual panel, double convector radiator offers the advantage of a standard 2” central connection and the standard 4 corner connection options. Pre-planning and installation are greatly reduced, saving time and money. The new T design allows installers the flexibility to connect to the most convenient location for installation.
The Myson T6 Radiator is a ready-to-install radiator and includes a wall- mounting bracket set, a thermostatic valve insert, drain-off plug, air bleed vent and compression fittings for 1/2” copper tubing. Compression fittings for 1/2” pex are available as a substitute. Herz TRV Head is available as an option.
Setting Information
- Bottom center connections must be used for internal valve function.
- Remove Site Cap or Probe Element.
- Turn the Setting Ring counter-clockwise to the desired presetting—the setting value (1, 2, … 7, N) must be positioned above the mark.
- Presetting can be selected in grades from 0.5 between 1 and 7. Presetting is released in the setting “N”.
Snap Element Details
With integrated anti-lift out device and a device that prevents movement
Wall Rail Details
DIMENSION
General Specifications
Approval and Certification
All MYSON T6 IVC Radiators are manufactured and tested to DIN EN 442
Operating Pressures and Temperatures Every Radiator is pressure tested to
188.5 psi Maximum working pressure 145 psi Maximum working temperature 230ºF
Paint Finish
Every Radiator undergoes a multistage pre-treatment process followed by an
epoxy polyester powder coat in white (RAL 9016) is applied to all front and
rear surfaces allowing the MYSON T6 IVC to be fitted without further painting.
Conversion Factors
Factors for differences between average water temperature and room temperature
in ºF other than 108ºF, (example: water temperature 180ºF minus room
temperature 72ºF equals T of 108ºF). See page 8 for Heat Output Adjustment
Factors.
Pressure Loss Graphs
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>