audio-technica ATW-R3210N UHF Wireless Systems User Manual

audio-technica ATW-R3210N UHF Wireless Systems

Product Information

• Product Name : 3000 Series UHF Wireless Systems
• Components
• ATW-R3210N Receive r
• ATW-T3201 Body-Pack Transmitter
• ATW-T3202 Handheld Transmitter
• Manufacturer: Audio
• Technica
• User Manual : https://manual-hub.com/

Product Usage Instructions

1. Making Connections (Basic Connections)
   • Connect the antenna to the antenna input jack on the rear panel of the ATW-R3210N receiver.
   • Connect the ATW-T3201 Body-Pack Transmitter or ATW-T3202 Handheld Transmitter to the ATW-R3210N receiver using the appropriate cables.
2. Achieving Stable Reception
   • Ensure that the receiver and transmitter are within the recommended operating range.
   • Avoid obstructions between the receiver and transmitter that may interfere with the signal.
   • If experiencing interference, try the following
   • Reorient or relocate the receiving antenna.
   • Increase the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
   • Consult the dealer or an experienced radio/TV technician for help.
3. Rack-mounting the Receiver
   • Follow the instructions provided in the user manual to rack-mount the ATW-R3210N receiver.
4. Troubleshooting
   • Refer to the troubleshooting section in the user manual (page 29) for assistance in resolving common issues.

Note: It is important to read through the entire user manual before using the product to ensure proper usage and understanding of all features and functions.

Introduction

Thank you for purchasing this Audio-Technica product.
Before using the product, read through this user manual to ensure that you will use the product correctly. Please keep this manual for future reference.

Important information

Warning
To prevent fire or shock hazard, do not expose this apparatus to rain or moisture.

Caution

• Do not expose this apparatus to drips or splashes.
• To avoid electric shock, do not open the cabinet.
• Refer servicing to qualified personnel only.
• Do not expose this apparatus to excessive heat such as that generated by sunshine, fire or other heat sources.
• Do not subject this apparatus to strong impact.
• This apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time.
• In case of emergency, disconnect the AC adapter quickly.
• Do not place any objects filled with liquids, such as vases, on this apparatus.
• To prevent fire, do not place any naked flame sources (such as lighted candles) on this apparatus.
• Do not install this apparatus in a confined space such as a bookcase or similar unit.
• Install this apparatus only in the places with good ventilation.
• The rating label is put on the bottom of this apparatus.

Battery caution

• Keep batteries out of the reach of children.
• Observe correct polarity as marked.
• Do not expose the battery to excessive heat such as sunshine, fire or the like.
• Always consider the environment issues and follow local regulations when disposing of batteries.
• Remove depleted battery immediately.
• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
• Use only disposable LR06(AA) alkaline or NiMH batteries.
• Do not use new batteries and old one at the same time.
• Do not use different battery types or models.
• Do not use a leaking battery. If battery leakage occurs, avoid contact with skin. If contact occurs, immediately wash thoroughly with soap and water.
• If battery leakage comes into contact with your eyes, immediately flush with water and seek medical attention.

For customers in the USA

FCC Notice

Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Caution
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

For customers in Canada

• IC statement
• CAN RSS-Gen/CNR-Gen
• This device complies with INDUSTRY CANADA R.S.S. 210. Operation is subject to the following conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference which may cause undesired operation.
• This device complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment.

Notes on use

• Be sure to read the user manual for any microphone or cable that you attach to the product.
• Disconnect the AC adapter from the outlet when this product is not in use.
• Turn off the power of this product before connecting or disconnecting cables.
• If you use the product near a TV or radio antenna, you may hear unwanted noise in the television or radio. If this occurs, move the product away from the device.
• Two waves of the same frequency can’t be used simultaneously.
• Be careful of interference noise caused by the surrounding radio wave environment and use of multiple systems.
• Wireless systems may be affected by the spark noise of vehicles, dimmer of lighting apparatus, computers, office automation apparatus and electronic musical instruments. Place and use the product where it is less likely to be affected by the above.
• Be sure to use this product in combination with components specified by our company.
• Be sure to use a general-purpose LAN that complies with the Ethernet standard (CAT5e or higher, with shielding is recommended).
• Disconnect the LAN cable when not using the network.
• Be sure the connected cable is plugged all the way into the product.
• When you connect the product with a mixer, turn off the phantom power source.
• If you use the product close to an electronic or communications device (such as a mobile phone), the product may produce unwanted noise. If this occurs, move the product away from the device.
• When setting up the product, make sure there are no obstacles between the transmitter and the receiver that might block the signal.
• To prevent the batteries from wearing out, turn the transmitter off when not in use.
• Over time, discoloration may occur due to ultraviolet rays (especially direct sunlight) and friction.
• It is legally prohibited to dismantle and modify this product. In addition, this product is so precisely manufactured that dismantling it could cause electric shock, failure or fire. Never dismantle this product.

Using multiple wireless systems

• If you use more than one device at the same time, use them in the same group.
• When using multiple units simultaneously, maintain 1 meter or more between individual transmitters and 3 meters or more between transmitters and receivers’ antennas.
• When using multiple units, power on transmitters one by one, making sure there is no unwanted noise.
• When a howling (beeping or squealing) sound is produced during use, turn down the output volume of the connected mixer/amplifier.

Maintenance

• If the product becomes stained or covered with dust, be sure to disconnect the power plug before wiping it off with a dry and soft cloth.
• Do not use benzine, thinner or electrical contact cleaner, etc. They may deform or otherwise damage the product, or cause operational failure.

Part names and functions

ATW-R3210N

Front panel

1. Power button ( )
   • Use to turn the receiver on or off.
2. IR sync window
   • Use to IR SYNC with the transmitter (ATW-T3201, ATW-T3202).
3. Display
   • Displays the receiver state and setting menus.
4. BACK button
   • Press to take the display back one screen.
   • Returns to the Main screen when pressed and held.
5. Control dial
   • Switches the screen when you turn the dial.
   • Displays the setting menu when you press the dial. Turn the dial to select a setting and press to confirm. When you press and hold the dial, QUICK SYNC is started.

Rear panel

1. Antenna input jack
   Each jack supplies DC12 V to a connected antenna.
   Additionally other compatible accessories (sold separately) can be connected.

2. Ground lift switch
   This switch isolates the GND pin of the balanced/unbalanced output from the ground.
   Normally this is kept in the GND position, but if a hum develops due to a ground loop, switch to the LIFT side.
   Balanced output jack (XLR 3-pin male)

3. Network interface
   By connecting to a PC via Ethernet, you can use the PC for monitoring and control. LAN : 100Base-TX

4. DC input terminal
   Connect DC plug from the included AC adapter.

5. AC adapter cord hook
   Hang the power cord of the AC adapter to prevent it from pulling loose accidentally.

ATW-T3201

1. Transmission antenna

2. MUTE switch
   Switches audio mute on and off.

3. Indicator
   LED that shows the status of the transmitter.
   When the power is turned ON: Solid green When the transmitter is muted: Solid red

4. Function button
   Press briefly to turn the screen back on if it shuts off. Press and hold to perform preselected function.

5. Input connector
   Connect a microphone, a headworn microphone, a guitar cable, etc.

6. Display
   Shows the current status.
   If no buttons are pressed for a period of 30 seconds, the display will turn off.

7. SYNC button
   Use to IR SYNC with the receiver (ATW-R3210N).

8. UP button
   Use to select various settings.

9. BACK button
   Press to return to the previous screen.
   Returns to the Main screen when pressed and held.

10. Power switch
    Use to turn the power on or off.

11. SET button
    Press to confirm a selection.

12. DOWN button
    Use to select various settings.

13. Battery cover

14. IR sync window
    Use to IR SYNC with the receiver (ATW-R3210N).

15. Charging terminal

ATW-T3202

1. Interchangeable microphone capsule

2. Display
   Shows the current status.
   If no buttons are pressed for a period of 30 seconds, the display will turn off.

3. Grip case

4. UP button
   Use to select various settings.

5. BACK button
   Press to return to the previous screen.
   Returns to the Main screen when pressed and held.

6. IR sync window
   Use to IR SYNC with the receiver (ATW-R3210N).

7. DOWN button
   Use to select various settings.

8. SET button
   Press to confirm a selection.

9. SYNC button
   Use to IR SYNC with the receiver (ATW-R3210N).

10. Power switch
    Use to turn the power on or off.

11. Battery cover

12. Function button
    Press to turn the screen back on if it shuts off. Press and hold to perform preselected function.

13. Indicator
    LED that shows the status of the transmitter.
    When the power is turned ON : Solid green When the transmitter is muted: Solid red

14. Charging terminal

How to insert batteries

ATW-T3201

1. Slide the battery cover latches down.
2. Open the battery cover while the latches are slid.
3. Insert the batteries according to the plus (+) and minus (-) marks found inside the battery compartment.

ATW-T3202

1. Rotate the grip case of the battery compartment.

2. Open the battery cover.
   Put your finger on the hook of battery cover and pull it to open the  battery cover.

3. Insert the batteries according to the plus (+) and minus (-) marks  found inside the battery compartment.

4. How to attach and detach the interchangeable microphone capsule (only for ATW-T3202)

How to attach

1. Attach the microphone capsule to the body of the transmitter.
2. Rotate the microphone capsule clockwise to tighten it.

How to remove

1. Rotate the microphone capsule counterclockwise to loosen it.
2. Detach the microphone capsule from the body of the transmitter.
   • Do not directly touch or scratch the connection surface.
   • Be sure to turn off the power of the transmitter before attaching/detaching the microphone capsule.
   • Do not forcibly attach the microphone capsule. Doing so may damage the transmitter or microphone capsule.

How to read the display

ATW-R3210N

Main screen

1. Transmitter information display area
   Information on the connected transmitter is displayed. Refer to “Transmitter information display area” (p. 10) for screen display.

2. RF level indicator
   Displays the strength of RF reception for antennas A and B.

3. Name display

4. Displays the specified name.
   Frequency indicator Displays the set frequency.

5. Receiver mute indicator
   A speaker icon with a slash through it is displayed when the receiver is muted.

6. AF level indicator
   Displays the strength of the received audio signal.

7. Group indicator

8. Channel indicator

9. Network indicator
   Icon is displayed when the receiver is connected to a network.

10. Backup frequency indicator
    “BU” icon is displayed when the backup frequency mode is ON.

11. Lock status indicator

12. Antenna input power indicator
    Icon is displayed when the antenna power supply is ON.

Transmitter information display area

1. Lock status indicator
2. High-pass filter indicator
3. RF transmission output indicator
4. Battery level indicator
5. Transmitter mute indicator
6. A microphone with a slash through it is displayed when the transmitter is muted.
7. Transmitter non-communication indicator

Level meter screen

1. RF transmission output indicator (transmitter)

2. Marker (when the minimum hold function is on) Shows the minimum level at which the RF is held.

3. Mute indicator
   A speaker icon with a slash through it is displayed when transmitter is muted.

4. Audio output indicator (receiver)

5. Gain indicator (transmitter)

6. Overload (excessive input) indicator

Minimum hold function
If you press the BACK button on the level meter screen, the minimum hold function turns on and its marker is displayed.

• The marker indicates the lowest level of RF signal received from the transmitter.
• The marker does not move if the input RF level is higher than the marker position.
• If the RF level input is lower than the marker position, the marker moves in tandem with the RF level.
• To reset the marker position, press the BACK button again.

Switching between screens
The screen is switched every time the control dial is rotated right or left.

ATW-T3201/ATW-T3202
The main screen is displayed when the power is switched on. If you press the UP/Down button on the main screen, the screen display is switched.

• Frequency indicator Displays the set frequency.
• Frequency indicator Displays the set frequency.
• Battery level indicator
• : 75% or more battery power remaining.
• : 50 to 75% battery power remaining.
• : 25 to 50% battery power remaining.
• : 25% or less battery power remaining.
• RF transmission output indicator
• : RF Power High (30 mW)
• : RF Power Low (10 mW)
• : RF Power Off
• High-pass filter indicator
• Name display
• Displays the specified name.
• Group indicator
• Channel indicator

Network
By connecting a receiver to a Windows PC/Mac, you can monitor and control the status of the receivers and the transmitters using a dedicated application, Wireless Manager.

What is Wireless Manager?
Wireless Manager is software that supports the setup, control, and monitoring of compatible Audio-Technica wireless devices. It allows the user to configure settings in the Device List tab, RF planning in the Frequency Coordination tab and keep track of critical system levels and alerts in the monitor tab. When linked to a compatible receiver, you can scan the RF environment, monitor connected devices, and view the system log.

• Read the user manual for any device used with this software.
• Before using Wireless Manager, update network settings as described in “Setting network” (p. 21).

How to operate

Basic operation

1. Turn on the power button of the receiver (ATW-R3210N).
   • The display lights and the main screen is displayed.
2. Set the operating frequency.
3. Turn on the power switch of the transmitter (ATW-T3201/ATW-T3202).
   • The indicator lights and the display shows the main screen.
4. Set the transmission frequency.
5. Check the RF level indicator on the receiver.
   • Check that antenna A or B lights up.
6. Speak into the microphone.
   • Make sure the AF level indicator lights up on the receiver.
   • Hold down the DOWN button of the transmitter while turning on the power switch to start up with the RF output in the OFF state (RF OFF mode).

Using IR SYNC
This function allows you to make settings on the receiver that are specified for the transmitter.

1. When IR SYNC is initiated on the receiver, the “Communication in standby” screen is displayed.
2. Position the IR sync windows of the receiver and transmitter so they face each other.
3. Press the SYNC button on the transmitter.
   • Wait several seconds until communication is established.
4. When the SYNC is complete, the “completed” screen is displayed.
   • The settings made on the receiver are automatically synced to the transmitter.
   • If an error occurs in the SYNC process, an error screen opens and then the display returns to the menu screen. Check the IR SYNC windows of the receiver and transmitter and then SYNC again.
   • To cancel the SYNC process, press the BACK button on the receiver. You will be returned to the previous screen.

Using QUICK SYNC
SYNC shortcut allows you to easily move to the settings screen where you can configure the transmitter settings from the receiver.

1. Press and hold the control dial on the main screen for approximately 2 seconds.
2. “TX SYNC” setting screen is displayed.
   • Refer to “Setting transmitters via IR SYNC” (p. 17) for subsequent steps.

Settings
Various settings can be made from the menu screen shown on the display.

ATW-R3210N

1. Press the control dial.
   • The main menu screen appears.
2. Turn the control dial to select the item you wish to set.
3. Press the control dial to open the settings menu of the selected item.
   • Press the BACK button to go back one screen.
   • To cancel partway through making a setting, press the BACK button.
   • While on the settings screen, the display will return to the main screen if approximately 60 seconds pass without a button or the control dial being used.

ATW-T3201/ATW-T3202

1. Press the SET button.
   • The menu screen appears.
2. Press the UP/DOWN button to select the item you wish to set.
3. Press the SET button to display the settings screen for the selected item.
   • Press the BACK button to go back one screen.
   • To cancel partway through making a setting, press the BACK button.
   • While on the settings screen, the display will return to the main screen if approximately 30 seconds pass without a button being used.

Setting ATW-R3210N

List of setting items

Gr/Ch
NAME| Set the channel name.
AUDIO| Set the audio output level.
GROUP SCAN| Scan for open channels.
TX SYNC| Set transmitters via IR SYNC.
SQUELCH| AUTO| Set the squelch level.
MANUAL
UTILITIES| LOCK| Set this function to prevent the receiver settings from being changed.
ANT PWR| Set whether to turn power on or off to the antenna input terminals.
Gr/Ch EDIT| Edit the channel allocation for user groups (U1 and U2).
BACKUP FREQ| Set the backup frequency.
DISPLAY| Set the item prominently displayed at the center of the main screen.
AF METER| Switch the level meter on the main screen between receiver and transmitter.
BRIGHTNESS| Set the display brightness.
ACCESS| Set the user access level.
RESET| This returns the receiver settings to their factory defaults.
VERSION| This function displays product information such as the version of the receiver.
NETWORK| DEVICE ID| Set the receiver’s ID No.
IP SETTING| Set the IP.
REMOTE CTRL| Set the remote control.
SYSLOG| Set whether to send the log message to the Syslog server.
DISCOVERY| Set automatic detection by the application.
NTP| Set the NTP (Network Time Protocol).
MAC ADDRESS| Display the MAC address.

Setting the operating frequency

Manual setting

1. From the menu screen, turn the control dial, select [FREQUENCY] and then press the control dial.
2. Select [MANUAL] and press the control dial.
3. Turn the control dial to set the first 3 digits. When finished setting them, press the control dial.
4. Turn the control dial to set the last 3 digits. When finished setting them, press the control dial.
   • The setting is complete.

Setting by group/channel

1. From the menu screen, turn the control dial, select [FREQUENCY] and then press the control dial.
2. Select [Gr/Ch] and press the control dial.
3. Turn the control dial to set the group. When finished setting it, press the control dial.
4. Turn the control dial to set the channel. When finished setting it, press the control dial.
   • The setting is complete.

Setting the channel (receiver) name
The following characters can be entered:

The following characters can be entered

1. From the menu screen, turn the control dial, select [NAME] and then press the control dial.
2. Turn the control dial, select the desired character and then press the control dial.
   • The character is input and the cursor moves.
3. Repeat the operation in Step 2 to enter all characters.
4. Turn the control dial, select [End] and then press the control dial.
   • The setting is complete.

Setting ATW-R3210N
Setting the audio output level

1. From the menu screen, turn the control dial, select [AUDIO] and then press the control dial.
2. Turn the control dial to set the audio output level.
   • The level changes 2 dB +/- each time you turn the control dial.
   • It can be set from -60 to 0 dB.
3. Press the control dial.
   • The setting is complete.

Scanning for open channels
Scan for unused channels in the current environment for use.

1. From the menu screen, turn the control dial, select [GROUP SCAN] and then press the control dial.
2. Turn the control dial to select the group you want to scan. After selecting a group, press the control dial.
3. Turn the control dial to select the preferred threshold. After selecting the threshold, press the control dial.
   • You can select [Normal], [High] or [Low] sensitivity
4. Scan starts.
5. Confirm the scan result by selecting [OK] and then pressing the control dial.
   • If you want to scan over again, select [Retry].
6. Available channels and frequencies are shown in a list. Turn the control dial, select an available channel and then press the control dial.
   • The setting is complete.

Setting transmitters via IR SYNC
This function allows you to make transmitter settings on the receiver and then automatically configure the transmitter via IR SYNC. The following are the available settings and setting values

1. From the menu screen, turn the control dial, select [TX SYNC] and then press the control dial.
2. Turn the control dial to select a setting you would like to sync to the transmitter and then press the control dial.
3. Turn the control dial to select the setting value and then press the control dial.
4. Repeat Steps 2 and 3 for each setting you would like to sync to the transmitter.
5. Turn the control dial, select [SYNC START] and then press the control dial.
   • Communication function is in standby.

Refer to “Using IR SYNC” (p. 14) for subsequent steps.

Setting the squelch level
Setting automatically

1. From the menu screen, turn the control dial, select [SQUELCH] and then press the control dial.

2. Turn the control dial, select [AUTO] and then press the control dial.

3. Turn the control dial, select [Normal], [High] or [Low] and then press the control dial.

   • You can select one from [Normal], [High] or [Low].
   • If an error message is displayed, change the operating frequency. The error indicates that the current frequency is already in use or that there is excessive noise.
     Scan starts.

4. The scan result is shown. Press the control dial.

   • The setting is complete.

Setting manually

1. From the menu screen, turn the control dial, select [SQUELCH] and then press the control dial.
2. Turn the control dial, select [MANUAL] and then press the control dial.
3. Turn the control dial to select the value you wish to set.
   • The meter indicates the RF level.
   • It can be set from levels 1 to 13.
   • While the available range of the transmitter becomes wider as the squelch level is lower, there may be cases when noises occur under the influence of other radio waves. While the available range of the transmitter becomes narrower as the squelch level is made higher, noises are less likely to occur due to the less influence of other radio waves.
4. Press the control dial.
   • The setting is complete.

Setting the system-related functions

Setting the lock
Set this function to prevent the receiver settings from being changed.

The default setting is [Unlock].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [LOCK] and then press the control dial.
3. Turn the control dial to select [Lock] or [Unlock], and then press the control dial.
   • The setting is complete.

Setting the antenna power
Set whether to turn power on or off to the antenna input terminals.

• The default setting is [Off].
• If set to [On], power is supplied to both antennas A and B.

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [ANT PWR] and then press the control dial.
3. Turn the control dial, select [On] or [Off] and then press the control dial.
   • The setting is complete.

Setting group/channel editing

Setting group/channel
Aside from the ten preset groups, there are two additional user-defined scan groups: U1 and U2. Both U1 and U2 can be edited with up to 32 frequencies.

All channels are vacant in the initial state.

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [Gr/Ch EDIT] and then press the control dial.
3. Turn the control dial, select [EDIT] and then press the control dial.
4. Turn the control dial, select a group and then press the control dial.
5. Turn the control dial, select a channel and then press the control dial.
6. Turn the control dial, select [SET] or [RESET] and then press the control dial.
   • By pressing [SET], you can set the frequency of the selected channel.
   • If you press [RESET], the frequency of the selected channel becomes blank.
7. After setting all channels, turn the control dial, select [Sync] or [Save] and then press the control dial.
   • If you press [Save], the setting is completed.
   • If you press [Sync], the screen turns to an IR SYNC standby screen. Refer to “Using IR SYNC” (p. 14) for subsequent steps.

Syncing the Group/Channel
The U1 or U2 Groups/Channels that have been set, as outlined above, can be sent to the transmitter via IR SYNC.

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [Gr/Ch EDIT] and then press the control dial.
3. Turn the control dial, select [Gr/Ch SYNC] and then press the control dial.
4.  Turn the control dial to select group and then press the control dial.
   • The screen turns to an IR SYNC standby screen. Refer to “Using IR SYNC” (p. 14) for subsequent steps.

Setting the backup frequency mode
If you set the backup frequency in advance, you can switch the frequency of the transmitter and receiver with the transmitter. It is convenient to set this function when you want to switch the frequency easily.

The default setting is [Off].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [BACKUP FREQ] and then press the control dial.
3. Turn the control dial, select [On] and then press the control dial.
4. Turn the control dial, select [Manual] or [Gr/Ch] and then press the control dial.
   • If you select [Manual], you can set the frequency.
   • If you select [Gr/Ch], you can set the group/channel.
5. After setting each item, turn the control dial, select [Set] or [Sync] and then press the control dial.
   • If you press [SET], the setting is completed but you must still sync the setting with the transmitter or set the backup frequency manually on the transmitter in order to use the backup frequency.
   • If you press [Sync], the screen turns to an IR SYNC standby screen. Execute IR SYNC.
   • After IR SYNC is complete, the transmitter’s function button switches to “Bkup Freq”. (p. 24).

Setting the layout of the main screen
Select the item to be prominently displayed at the center of the main screen.

The default setting is [Frequency].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [DISPLAY] and then press the control dial.
3. Turn the control dial, select [Frequency] or [Name] or [Gr/Ch] and then press the control dial.
   • The setting is complete.

Setting the AF level meter on the main screen
Switch the AF level meter on the main screen between [Rx] (Receiver) and [Tx] (Transmitter).

The default setting is [Rx].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [AF METER] and then press the control dial.
3. Turn the control dial, select [Rx] or [Tx] and then press the control dial.
   • The setting is complete.

Setting the display brightness
The default setting is [High].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [BRIGHTNESS] and then press the control dial.
3. Turn the control dial, select [High] or [Low] and then press the control dial.
   • The setting is complete.

Setting the user access level
Set the user access level.

The default setting is [Free Tuning].

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [ACCESS] and then press the control dial.
3. Turn the control dial, select [Free Tuning] or [User Group Only] and then press the control dial.

and U2).

The setting is complete.

Resetting
This returns the receiver settings to their factory defaults.

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [RESET] and then press the control dial.
3. Turn the control dial, select [Yes] and then press the control dial.
4. After the confirmation screen is displayed, turn the control dial again to select [Yes] and then press the control dial.
   • Reset starts.

Checking the receiver information
This function displays the receiver information.

1. From the menu screen, turn the control dial, select [UTILITIES] and then press the control dial.
2. Turn the control dial, select [VERSION].

Setting network
By connecting a receiver to a Windows PC/Mac, you can monitor and control the status of the receivers and the transmitters using a dedicated application, Wireless Manager.

Setting the receiver’s ID No.

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [DEVICE ID] and then press the control dial.
3. Turn the control dial, select the device ID and then press the control dial.
   • The setting is complete.

Setting the IP

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [IP SETTING] and then press the control dial.
3. Select an item you want to set and press the control dial.

IP Mode| Set how to obtain IP addresses.

[Auto]: IP addresses are automatically assigned.

[Static]: Set to use the specified static IP addresses.

---|---
IP Address| Specify static IP addresses.
Subnet Mask| Set the subnet mask.
Gateway*| Set the gateway.

*This item can be set only when [IP Mode] is set to [Static].

• Set each item.

Setting the remote control

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [REMOTE CTRL] and then press the control dial.
3. Select an item you want to set and press the control dial.

from the receiver during remote control.
Multicast Port| Set the port number for multicast.
Multicast IP| Set the address for multicast.

*This item can be set only when [Notification] is set to [ON].

• Set each item.

Setting the log message
Set whether to send the log message to the Syslog server.

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [SYSLOG] and then press the control dial.
3. Turn the control dial, select [On] or [Off] and then press the control dial.
   • The setting is complete.
   • Syslog is a standard for transferring log messages across IP networks. It is used for administration of computer systems and security monitoring.

Setting automatic detection by the application

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [DISCOVERY] and then press the control dial.
3. Turn the control dial, select [On] or [Off] and then press the control dial.
   • The setting is complete.

Setting NTP
Set the NTP (Network Time Protocol).

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [NTP] and then press the control dial.
3. Select an item you want to set and press the control dial.

Time).
DST1| Turn on/off the daylight saving time.
Date2| Set the starting/ending date of daylight saving time.
Time*2| Set the starting/ending time of daylight saving time.

1. This item can be set only when [NTP] is set to [ON].
2. This item can be set only when [DST] is set to [ON].
3. Set each item.

Setting MAC address

1. From the menu screen, turn the control dial, select [NETWORK] and then press the control dial.
2. Turn the control dial, select [MAC ADDRESS].

Setting ATW-T3201/ATW-T3202

Gr/Ch
NAME| Set the channel name.
GAIN| Set the gain.
RF POWER| Set the transmission output.
HPF| Set HPF (High-Pass Filter).
LOCK| Set a lock.
Fn BUTTON| Set the function allocation for function button.
MUTE MODE (ATW-T3201

only)

| Set the mute mode.
UTILITIES| BATTERY| Set the type of batteries used.
LED| Set whether to constantly keep indicator turned on or off.
ACCESS| Set the user access level.
RESET| This returns the transmitter settings to their factory defaults.
VERSION| It shows the version of the transmitter.

Setting the transmission frequency

Setting manually

1. From the menu screen, press the UP/DOWN button to select [FREQUENCY], and then press the SET button.
2. [FREQUENCY], and then press the SET button.
3. Press the UP/DOWN button to set the first 3 digits. After completing the setting, press the SET button.
4. Press the UP/DOWN button to set the last 3 digits. After completing the setting, press the SET button.
   • The setting is complete.

Setting by group/channel

1. From the menu screen, press the UP/DOWN button to select [FREQUENCY], and then press the SET button.
2. After selecting [Gr/Ch], press the SET button.
3. Press the UP/DOWN button to set the group. After completing the setting, press the SET button.
4. Press the UP/DOWN button to set the channel. After completing the setting, press the SET button.
   • The setting is complete.

Setting the channel (transmitter) name
The following characters can be entered:

The maximum number of characters that can be entered is 8.

1. From the menu screen, press the UP/DOWN button to select [NAME], and then press the SET button.
2. Press the UP/DOWN to select a desired character and press the SET button.
   • The character is input and the cursor moves.
3. Repeat the operation in Step 2 to enter all characters.
   • If you don’t enter 8 characters, press the UP/DOWN button and select [End] and then press the SET button.
4. After entering the 8th character, press the SET button.
   • [End] is displayed.
5. Press the SET button.
   • The setting is complete.

Setting the gain

1. From the menu screen, press the UP/DOWN button to select [GAIN], and then press the SET button.
2. Press the UP/DOWN button to select the gain you wish to set.
   • The level changes 2 dB +/- each time you press the UP/DOWN button.
   • It can be set from -10 to +20 dB.
3. Press the SET button.
   • The setting is complete.

Setting the RF transmission output

1. From the menu screen, press the UP/DOWN button to select [RF POWER], and then press the SET button.
2. Press the UP/DOWN button and select [High:30mW],[Low:10mW] or [Off].
3. Press the SET button.
   • The setting is complete.

Setting HPF (High-Pass Filter)

1. From the menu screen, press the UP/DOWN button to select [HPF], and then press the SET button.
2. Press the UP/DOWN button to select [On] or [Off].
3. Press the SET button.
   • The setting is complete.

Setting lock

1. From the menu screen, press the UP/DOWN button to select [LOCK], and then press the SET button.
2. Press the UP/DOWN button to select [Lock] or [Unlock].

1. Press the SET button.
   • The setting is complete.

Setting the function for the function button
Select the function to be performed when the function button is pressed and held.

1. From the menu screen, press the UP/DOWN button to select [Fn BUTTON], and then press the SET button.
2. Press the UP/DOWN button to select the function you wish to set.

Mute

(only for ATW-T3202)

| Mutes the transmitter
MuteOnLock

(only for ATW-T3202)

| Mutes the transmitter (even when transmitter buttons are locked)
Bkup Freq| Switches to backup frequency (When selected, set the frequency, group, and channel.)
RF Off| Turns off RF transmission output

1. Press the SET button.
   • The setting is complete.

Setting the mute mode (only for ATW-T3201)
Set the function of the MUTE switch.

1. From the menu screen, press the UP/DOWN button to select [MUTE MODE], and then press the SET button.
2. Press the UP/DOWN button to select the mode you wish to set.

1. Press the SET button.
   • The setting is complete.

Setting the system-related functions

Setting the battery type
Set the type of batteries used.

The default setting is [Alkaline].

1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button.
2. Press the UP/DOWN button to select [BATTERY] and press the SET button.
3. Press the UP/DOWN button to select the battery you wish to set.

1. Press the SET button.
   • The setting is complete.
   • If the appropriate setting is not made for the batteries used, the battery power indicator will not display the correct information. Always set the type of battery according to the batteries used.

Setting the indicator
The indicator LED can be turned [On] or [Off].

The default setting is [On].

1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button.
2. Press the UP/DOWN button to select [LED] and press the SET button.
3. Press the UP/DOWN button to select [On] or [Off].
4. Press the SET button.
   • The setting is complete.

Setting the user access level
Set the user access level.

The default setting is [Free].

1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button.
2. Press the UP/DOWN button to select [ACCESS] and press the SET button.
3. Press the UP/DOWN button to select [Free] or [UserGroup].

U2).

1. Press the SET button.
   • The setting is complete.

Resetting
This returns the transmitter settings to their factory defaults.

1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button.
2. Press the UP/DOWN button to select [RESET] and press the SET button.
3. Press the UP/DOWN button to select [Yes].
4. When the confirmation screen is shown, press the UP/DOWN button again to select [Yes].
5. Press the SET button.
   • Reset starts.

Checking the transmitter information
This function displays the firmware version for the transmitter.

1. From the menu screen, press the UP/DOWN button to select [UTILITIES], and then press the SET button.
2. Press the UP/DOWN button to select [VERSION] and press the SET button.
   • The version is shown.

How to attach the transmitter (ATW-T3201)
The ATW-T3201 transmitter is equipped with a clip that can be used to attach the transmitter to a belt, etc.

• You can reverse the direction of the input connector by attaching the clip in the opposite direction.
• Pull both sides of the clip firmly to the outside to remove the clip from the product.

Making connections (basic connections)
This is an example of connections made when using one receiver.
When connecting more than one receiver via a distributor (sold separately), refer to the distributor’s user manual.

Achieving stable reception
Low RF signal may result if there are obstructions between receiver antennas and transmitter(s). In such a case, reposition the antennas to get better reception. Use external antennas (sold separately) if the installation space is limited.

Rack-mounting the receiver

• Screws for rack-mounting the receiver are not included.
• Consider ventilation when rack-mounting to avoid heat building up in the rack.

Troubleshooting

ATW-R3210N

Confirm that all connected components, such as a mixer, are correctly connected to the receiver.|

–

Confirm that the audio output isn’t set to the minimum level.| (p. 17)
Confirm that the audio output level of connected components (such as a mixer) is not minimized.|

–

Sound is distorted.| Confirm that the audio output level isn’t too high.| (p. 17)
Confirm that the volume of any connected component isn’t too high.| –

There is unwanted noise.

| Confirm that there is no noise source, such as a fluorescent lamp or electric component, near the receiver.|

–

Confirm that each transmitter is using a different frequency.| –
Confirm that the output terminal of the receiver is correctly connected.| (p. 27)
Confirm that the receiver isn’t taking power from an electrical outlet that is also being used by another noisy component.|

–

Confirm that there isn’t any other nearby wireless system using the same frequency band. Adjust the squelch level.|

(p. 18)

ATW-T3201/ATW-T3202

24. Confirm that the microphone or the guitar cable is not disconnected (only for ATW- T3201).|

–

Confirm that the output volume of the musical instrument, such as a guitar, isn’t set at the minimum level.|

–

Confirm that the microphone capsule is connected properly (only for ATW-T3202).| (p. 9)
Sound is distorted.| Confirm that the gain setting of the transmitter is not too high.| (p. 24)

There is unwanted noise.

| Confirm that there is no noise source, such as a fluorescent lamp, LED lamp, or electric component, near the transmitter.|

–

Confirm that each transmitter is using a different frequency.| –
Confirm that the transmission output setting of the transmitter is not too high.| (p. 24)

Dimensions

ATW-T3201

Specifications

Overall system specifications

1. Please note that some frequency bands might not be available in your territory or could come with a limited tuning bandwidth/transmitting power due to local regulations.
2. Open range environment with no interfering signals.
3. Frequency response depends on attached microphone element.
4. For assistance with multi-band operation or other frequency coordination issues, Contact your local audio-technica dealer.
5. Region and band dependent

Specifications

1. Please note that some frequency bands might not be available in your territory or could come with a limited tuning bandwidth/transmitting power due to local regulations.
2. Open range environment with no interfering signals.
3. Frequency response depends on attached microphone element.
4. For assistance with multi-band operation or other frequency coordination issues, Contact your local audio-technica dealer.
5. Region and band dependent

• Depending on battery type, usage and environmental conditions.

• Depending on battery type, usage and environmental conditions.
• For product improvement, the product is subject to modification without notice.

Audio-Technica Corporation

• 2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan www.audio-technica.com
• ©2019 Audio-Technica Corporation
• Global Support Contact : www.at-globalsupport.com

References

• Global Support｜Audio-Technica Corporation オーディオテクニカ
• Audio-Technica Corporation | Headphones, Microphones & Turntables | Audio-Technica
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>