ATHENA GTX GTX 471-0011-05 Wireless Patient Monitoring Instructions
- June 13, 2024
- ATHENA GTX
Table of Contents
ATHENA GTX GTX 471-0011-05 Wireless Patient Monitoring
Product Information
- Product Name: Athena-GTX, Inc. Model 471-0011-05
- FCC ID: 2AVRK-BMD301
Configuration : Singular modular use configuration
Addendum: This addendum is created to support changes and replaces FCC publication 996369 related information on uBlox LLC Users Manual BMD-300-DS-V0.9.4 dated 03/23/2016, except where specifically stated.
Reference: uBlox LLC Users Manual BMD-300-DS-V0.9.4 dated 03/23/2016 or greater for additional user guide information.
Product Usage Instructions
- Ensure that the uBlox BLE Module is integrated with the Host Device.
- Refer to FCC approved antennas (2.4 GHz) identified in section 2.7 of the addendum for proper antenna selection.
- The BLE module will communicate (TX/RX) using 2.4 GHz at the default power setting (0dBM).
- Follow the appropriate duty cycle for the device.
Athena-GTX, Inc. addendum
Model 471-0011-05, FCC ID: 2AVRK-BMD301 is configured in a specific singular
modular use configuration, this addendum is created to support changes.
Information in this addendum is designed to replace FCC publication 996369
related information on uBlox LLC Users Manual BMD-300-DS-V0.9.4 dated
03/23/2016, except where specifically stated.
Refence uBlox LLC Users Manual BMD-300-DS-V0.9.4 dated 03/23/2016 or greater
for additional user guide information.
FCC publication 996369 related information
In publication 996369 section D03, the FCC requires information concerning a module to be presented by OEM manufacturers. This section assists in answering or fulfilling these requirements.
General
No requirements are associated with this section.
List of applicable FCC rules
This module conforms to FCC Part 15.249.
Summarize the specific operational use conditions
For the uBlox BLE Module, see FCC approved antennas (2.4 GHz) identified in
section 2.7 of this addendum.
Once integrated with the Host Device, the BLE module will communicate (TX/RX)
using 2.4 GHz at the default power setting (0dBM), duty cycle <100%.
Users are not permitted to modify antenna or alter pre-defined Host or Module
configuration settings, outside of connecting and disconnect other devices.
Limited module procedures
Not applicable.
Trace antenna designs
Not applicable.
RF exposure considerations
No changes to RF exposure.
Antennas
The Taoglas FXP73.07.0100A, 2.5dBi, 1/4 Wave Dipole – Flex 7mm x 47mm x 0.1mm
(or equivalent specification) antenna is approved to be used for this module.
Label and compliance information
A physical label stating “Contains FCC ID: 2AVRK- BMD301”, shall be used on
the outside of the enclosure of the host product.
Information on test modes and additional testing requirements
Devices shall be reviewed under configured max operational settings (standard
use) for SAR, Spurious Radiated Emissions. Unintentional Radiators is also
required for review, however, due to setting requirements (RF modules
disabled), only Athena GTX Inc. is permitted to configure a test unit for this
mode.
When testing for all, except for Unintentional Radiators, BLE must be tested
after a connection with a partnering device is established and information is
transmitting. Additionally, Wi-Fi and BLE shall be co-located, as such, it
needs to be paired with a compatible device to allow RF traffic.
Antenna power, duty cycle, and transmission rate cannot be altered from
approved settings, see RF Exposure report for technical information.
Additional testing, Part 15 Subpart B disclaimer
Not applicable, see this section in original uBlox LLC Users Manual
BMD-300-DS-V0.9.4 dated 03/23/2016 or greater.
5900 NW 86TH Street • Suite 300 • Johnston, IA 50131 • 515.288.3360 • www.athenagtx.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>